• 한국염색가공학회지
• /
• 제31권2호
• /
• pp.107-117
• /
• 2019

In case of pure rubber materials, the initial quality of the rubber materials would be excellent, however, the durability against external impact might be poor. In order to overcome the relatively low durability, textile cord could be employed with silicone rubber. We have studied the improvement of heat-resistant adhesion properties of silicone adhesives between silicone rubber and PET fibers by applying various conditions including dip solution recipe. The silicone rubber used was a platinum catalyst curing type and platinum catalyst type silicone adhesive was used as an adhesive to obtain an optimum adhesive force. Furthermore, the bonding mechanism between silicone and PET fiber was established.

• 반도체디스플레이기술학회지
• /
• 제17권1호
• /
• pp.35-39
• /
• 2018

This paper deals with the relaxation of singular stresses developed in an epoxy adhesive at high temperature. The interface stresses are analyzed using BEM. The adhesive employed in this study is an epoxy which can be cured at room temperature. The adhesive is assumed to be linearly viscoelastic. First, the distribution of the interface stresses developed in the adhesive layer under the uniform tensile stress has been calculated. The singular stress has been observed near the interface corner. Such singular stresses near the interface corner may cause epoxy layer separated from adherent. Second, the interfacial thermal stress has been investigated. The uniform temperature rise can relieve the stress level developed in the adhesive layer under the external loading, which can be viewed as an advantage of thermal loading. It is also obvious that temperature rise reduces the bonding strength of the adhesive layer. Experimental evaluation is required to assess a trade-off between the advantageous and deleterious effects of temperature.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권3호
• /
• pp.105-115
• /
• 2007

리모델링의 증가로 보수보강에 대하여 많은 관심을 갖게 되었다. 탄소섬유시트의 사용은 철근콘크리트 구조의 강성을 증가시키기 위하여 많이 쓰이고 있다. 따라서 새로운 보강방법으로 외부 부착에 의한 강성이 증가된 RC구조의 휨거동을 알아보기 위하여 실험과 분석 연구를 수행하였다. 또한 본 연구는 실험에 의한 피로하중을 받도록 한 FRP패널 보강방법에 대하여 살펴보는데 그 목적이 있다.

• 스마트미디어저널
• /
• 제6권1호
• /
• pp.9-15
• /
• 2017

ICT 분야의 메가 트렌드는 IoT, Bigdata, 그리고 Cloud Computing 으로 집약된다. 이러한 메가 트렌드들은 독립적으로 운영되지 않으며, 이를 지원하기 위한 백그라운드에는 대용량 컴퓨팅 기술이 필요하듯 대용량 스토리지 기술이 필수적이다. 오픈소스 Ceph 기반의 대용량 스토리지의 성능 평가를 위하여 교육망인 KOREN 네트워크를 이용한 국내 및 해외 사이트와의 Abyss Storage의 실증 테스트를 수행한다. 또한, 스토리지 자체의 성능 평가를 위하여 스토리지 매체와 네트워크 본딩의 성능 테스트를 수행한다. 스토리지 매체별로 실질적인 속도 차이는 크지만 수행된 스토리지 매체 테스트에서는 크게 성능 차이를 보이지 않았다. 이를 해결하기 위한 방안으로 네트워크 가속화를 통한 성능 향상을 얻을 수 있었다. 또한 KOREN 망을 이용한 국내 및 해외 사이트를 연결하여 Abyss Storage의 내부 및 외부 네트워크의 실질적인 성능 테스트를 수행하였다.

• 대한토목학회논문집
• /
• 제30권3A호
• /
• pp.221-228
• /
• 2010

탄소섬유시트 보강공법은 열화 손상된 콘크리트 구조물의 보강에 가장 많이 사용되는 보강공법 중 하나이다. 탄소섬유시트 보강공법은 에폭시접착제를 사용하여 탄소섬유시트를 콘크리트의 외부에 부착하는 보강공법으로 탄소섬유시트에 의한 휨보강이 에폭시 접착 경계면을 통하여 콘크리트로 전달된다. 따라서 사용기간이 경과함에 따라 에폭시 접착 경계면에 발생하는 크리프 등의 시간의존적 거동은 보강효과를 감소시키는 요인이 된다. 본 연구에서는 경계면에서 발생하는 크리프 영향을 해석하기 위하여 콘크리트의 크리프 거동에 대한 기존의 연구들을 고찰하고, 이를 바탕으로 에폭시 접착 경계면의 크리프 영향을 예측할 수 있는 이론적인 연구를 수행하였다. 제안된 유한요소해석기법은 기존의 콘크리트 크리프 거동 분석을 위해 사용되던 유변모델을 에폭시 접착 경계면에 적용한 것으로 기존 실험결과와 비교를 통하여 타당성을 검증하였다. 또한, 제안된 유한요소해석을 통하여 탄소섬유시트로 보강된 콘크리트 구조물의 시간의존적 거동에 경계면 재료의 크리프 영향을 반드시 고려해야 한다는 것을 입증하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• 방사선산업학회지
• /
• 제6권1호
• /
• pp.31-40
• /
• 2012

There are two methods to fabricate the readout electronic to a large-area CMOS image sensor (LACIS). One is to design and manufacture the sensor part and signal processing electronics in a single chip and the other is to integrate both parts with bump bonding or wire bonding after manufacturing both parts separately. The latter method has an advantage of the high yield because the optimized and specialized fabrication process can be chosen in designing and manufacturing each part. In this paper, LACIS chip, that is optimized design for the latter method of fabrication, is presented. The LACIS chip consists of a 3-TR pixel photodiode array, row driver (or called as a gate driver) circuit, and bonding pads to the external readout ICs. Among 4 types of the photodiode structure available in a standard CMOS process, $N_{photo}/P_{epi}$ type photodiode showed the highest quantum efficiency in the simulation study, though it requires one additional mask to control the doping concentration of $N_{photo}$ layer. The optimized channel widths and lengths of 3 pixel transistors are also determined by simulation. The select transistor is not significantly affected by channel length and width. But source follower transistor is strongly influenced by length and width. In row driver, to reduce signal time delay by high capacitance at output node, three stage inverter drivers are used. And channel width of the inverter driver increases gradually in each step. The sensor has very long metal wire that is about 170 mm. The repeater consisted of inverters is applied proper amount of pixel rows. It can help to reduce the long metal-line delay.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2000년도 추계학술대회 논문집
• /
• pp.91-97
• /
• 2000

The conventional model did not take momentum conservation into consideration when the electron absorbs and emits the photons. II-ray provides momentum conservations on any directions of the entering photons, and also the electrons have radial momentum conservations and fully elastic bouncing between two atoms, in the new atom model. Conventional atom model must be criticized on the following four points. (1) Natural motions between positive and negative entities are not circular motions but linear going and returning ones, for examples sexual motion, tidal motion, day and night etc. Because the radius of hydrogen atom's electron orbit is the order of 10$^{-11}$ m and the radia of the nucleons in the nucleus are the order of 10$^{-l4}$m and then the converging n-gamma rays to the nucleus have so great circular momentum, the electron can not have a circular motion. We can say without doubt that any elementary mass particle can have only linear motion because of the n-rays' hindrances, near the nucleus. (2) Potential energy generation was neglected when electron changes its orbit from outer one to inner one. The h v is the kinetic energy of the photo-electron. The total energy difference between orbits comprises kinetic and potential energies. (3) The structure of the space must be taken into consideration because the properties of the electron do not change during the transition from outer orbit to inner one even though it produces photon. (4) Total energy conservation law applies to the energy flow between mind and matter because we daily experiences a interconnection between mind and body. An understanding of the mechanisms responsible for the control of normal proliferation and differentiation of the various cell types which make up the human body will undoubtedly allow a greater insight into the abnormal growth of cells, A large body of biochemical evidence was eventually used to generate a receptor model with an external ligand binding domain linked through a single trans-membrane domain to the cytoplasmic tyrosine kinase and autophosphory-lation domains. The ligand induced conformational change in the external domain generates either a push-pull or rotational signal which is transduced from the outside to the inside of cell.l.ell.

• Journal of the Korean Wood Science and Technology
• /
• 제48권5호
• /
• pp.581-590
• /
• 2020

Pulp refining is the major way to alter the properties of fibers and formed paper. Different combinations of the bar profile of the rotor and stator during low consistency refining processes directly affect the properties of the paper. In this study, a mixture of softwood and hardwood pulp was refined by varying the bar angle of the stator while that of the rotor is fixed at 0º. The pulp samples were collected at different refining times. Then, the pulp and paper properties, such as beating degree, fiber external fibrillation, and tensile and tear indexes were measured to explore the effects of the combined refining plates at different bar angles on paper properties. The results of the experiment show that the combined refining plate of 0º and 5º recorded the most significant improvement in the pulp beating degree and fiber external fibrillation. This consequently increased the fiber bonding area, which in turn, improved both the tensile and the tear indexes of the paper. Also, the influence of the combined refining plates with a larger bar angle on the paper properties was weaker compared to that of smaller angles. This study not only provides ideas for the bar profile design but also improves the optimal selection of refining plates.

• Journal of the Korean Wood Science and Technology
• /
• 제51권4호
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.