• 열처리공학회지
• /
• 제28권1호
• /
• pp.7-16
• /
• 2015

The fabrication of high quality graphene using chemical vapor deposition (CVD) method for application in semiconductor, display and transparent electrodes is investigated. Temperature and pressure have major impact on the growth of graphene. Graphene doping was obtained by deposition of $MoO_3$ thin films using thermal evaporator. Bilayer graphene and the metal layer graphene were obtained. According to the behavior of graphene growth P-type doping was confirmed. Graphene obtained through experiments was analyzed using optical microscopy, Raman spectroscopy, UV-visible light spectrophotometer, 4-point probe sheet resistance meter and atomic force microscopy.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1640-1647
• /
• 2004

This study was to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in an IDI diesel engine. The fuel injection timing was also controlled to investigate a method for the simultaneous reduction of smoke and NOx when water was injected into the combustion chamber. The formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water played a role as a heat sink during evaporating in the combustion chamber, while the smoke was slightly increased with increased water amount. Also, NOx emission was significantly decreased with increase in water amount. A simultaneous reduction in smoke and NOx emissions was obtained when water was injected into the combustion chamber by retarding more 2$^{\circ}C$A of the fuel injection timing than without water injection.

• 한국염색가공학회지
• /
• 제17권1호
• /
• pp.38-44
• /
• 2005

Oxidation method was used to extract S-keratose from wool. Wool was treated with performic acid and soluble fraction(S-keratose) was collected by evaporating the solvent. S-keratose and Nylon 6 were dissolved in formic acid at the ratio of 100/0, 80/20, 50/50, 20/80, and 0/100, and S-keratose/Nylon 6 web of sub-micron size was made by electro-spinning technique. SEM, EA, FT-IR, XRD, and TGA were used to characterize the properties of S-keratose/Nylon 6 solutions and electrospun fibers. As the Nylon 6 content increased, viscosity, conductivity of the electrospinning solution and the diameter of spun fiber increased. Electrospun nonwoven webs have the same S-keratose/Nylon 6 ratios of the spinning solutions. The crystalline structures of S-keratose and Nylon 6 existed separately in the electrospun webs. Thermal stability of the webs increased due to Nylon 6 content.

• 대한기계학회논문집B
• /
• 제31권9호
• /
• pp.764-771
• /
• 2007

The objective of the present work is to evaluate the evaporation heat flux of deposited droplet on the hot surface by using of inverse heat transfer technique. On the basis of measured temperature, a integral form solution is determined for the transient temperatures beyond the two positions by using Green's function technique. This method first approximates the temperature data with a half polynomial series of time. we compared this result with constant radius model in single phase regime, nucleate boiling regime, film boiling regime respectively. this paper performed the experiments as following conditions: (a)the surface temperature is within the range between $80^{\circ}C\;and\;160^{\circ}C$ in the conduction, (b) droplet diameter are 2.4 and 3.0mm. (c) surface roughness is $0.18{\mu}m$.

• 오토저널
• /
• 제12권5호
• /
• pp.76-84
• /
• 1990

To study diesel fuel spray behavior, an experimental study was undertaken to investigate injection characteristics in vary ing back pressure and atomization mechanism in a non-evaporating diesel spray. Generally, injection characteristics is the curve of fuel flow plotted against time. The area under this curve is equal to the total quantity of fuel discharged for one injection. The method that measures rate of injection is long tube-type fuel rate indicator. Diesel spray injected into a quiescent gaseous environment under high pressure is observed by taking high speed camera by the focused shadow photographs. The results show that, at the start of injection, as the injected fuel rushes into the quiescent atmosphere the spray angle becomes large. Finally the spray stabilizes at a constant cone angle. Spray penetration length increases with the injection pressure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.71-72
• /
• 2006

The stochiometric mixture of evaporating materials for the $ZnIn_2S_4$ single crystal thin film was prepared from horizontal furnace. To obtain the $ZnIn_2S_4$ single crystal thin film. $ZnIn_2S_4$ mixed crystal was deposited on throughly etched semi-insulating GaAs(100). In the Hot Wall Epitaxy(HWE) system. From the photocurrent spectrum by illumination of perpendicular light on the c-axis of the $ZnIn_2S_4$ single crystal thin film, we have found that the values of spin orbit splitting ${\Delta}So$ and the crystal field splitting ${\Delta}Cr$ were 0.0148 eV and 0.1678 eV at $10_{\circ}K$, respectively.

• 한국과학교육학회지
• /
• 제8권1호
• /
• pp.33-42
• /
• 1988

Secondary school students' conceptions about the phenomena of evaporating, condensing, boiling and melting of ice using a modified questionare-about-events method. The specific views at each grade level were also studied. The results of investigation were as following. 1) Students' understanding on the sciencific concepts and terms is superficial and nonscientific. 2) Even though upper grade students have exposed to a considerable science teaching, their views are similar to lower grade students. 3) Certain views on the change of state of water can change with the advanced science teaching. However, some nonscientific views are more popular with the older students than with the younger students.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.143-144
• /
• 2008

Single crystal $ZnIn_2S_4$ layers were grown on a thoroughly etched semi-insulating GaAs(100) substrate at $450^{\circ}C$ with the hot wall epitaxy (HWE) system by evaporating the polycrystal source of $ZnIn_2S_4$ at $610^{\circ}C$ prepared from horizontal electric furnace. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of single crystal $ZnIn_2S_4$ thin films measured with Hall effect by van der Pauw method are $8.51\times10^{17}$ electron/$cm^{-3}$, 291 $cm^2$/v-s at 293 K, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.96-97
• /
• 2008

Single crystal $AgGaSe_2$ layers were grown on thoroughly etched semi-insulating GaAs(100) substrate at 420 $^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating $AgGaSe_2$ source at 630 $^{\circ}C$. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of single crystal $AgGaSe_2$ thin films measured with Hall effect by van def Pauw method are $9.24\times10^{16}cm^{-3}$ and 295 $cm^2/V{\cdot}s$ at 293 K, respectively.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 추계 학술대회논문집
• /
• pp.108-113
• /
• 1998

A numerical investigation for the flow, heat and mass transfer characteristics of the grooved evaporating tube with the films flowing down on both the inside and outside tube walls has been carried out. The condensation occurs along the outside wall while the evaporation takes place at the free surface of the inside film. The 3-D transport equations for momentum and energy are solved by using the FVM(Finite Volume Method). The free surface shape is tracked by the moving grid technique satisfying the SCL(Space Conservation Rule). Due to the secondary motion of the fluid, the film thins at the crest, while thickens at the valley. The velocity and temperature fields as well as the amounts of the condensed and evaporated mass have been successfully predicted for various operating conditions and groove shapes.