• 한국표면공학회지
• /
• 제49권1호
• /
• pp.69-74
• /
• 2016

In order to investigate the effect of NiO on the ethanol gas sensing performance of ${\alpha}-Fe_2O_3$ nanoparticles, NiO and ${\alpha}-Fe_2O_3$ nanoparticles are synthesized by hydrothermal method. The sensor with ${\alpha}-Fe_2O_3$ and NiO nanoparticles mixed at an optimum ratio of 7:3 showed 3.8 times improved sensing performance for 200ppm ethanol gas at $200^{\circ}C$. The enhanced gas sensing performance can be considered to be caused by pn heterojunction at the grain boundaries of ${\alpha}-Fe_2O_3$ and NiO nanopartcles.

• 한국재료학회지
• /
• 제13권3호
• /
• pp.155-159
• /
• 2003

The polypyrrole and polyaniline thin film sensors which were made by chemical polymerization were employed to detect ethanol gas. With a single sensor element we can obtain characteristic patterns of behaviour across a very wide frequency range when measuring either resistance or capacitance. Impedance spectroscopy was employed to study the gas sensing behavior of both capacitance and resistance based sensors with conducting polymer as the active sensing element.

• 한국표면공학회지
• /
• 제50권3호
• /
• pp.225-229
• /
• 2017

ZnO nanotubes were synthesized to investigate the effect of wall thickness on the ethanol gas sensing performance. The wall thickness of the nanotubes was varied from approximately 20 to 60 nm. Transmission electron microscopy, X-ray diffraction and SAED (Selected Area Electron Beam Diffraction) analyses showed that the synthesized nanotubes were polycrystalline structured ZnO with the diameter of approximately 200-300nm. The ZnO nanotubes sensor with an optimum wall thickness of 51.8nm showed approximately 8 times higher response, compared to that with 21.14nm wall thick nanotubes, to the ethanol concentration of 500 ppm at the temperature of $300^{\circ}C$. The wall thickness of 51.8nm was found to be a little larger than 46nm, which was theoretically derived Debye length. Along with the study of the wall thickness effect on the performance of the sensors, the mechanisms of gas sensing of the polycrystalline ZnO nanotubes are also discussed.

• 한국표면공학회지
• /
• 제49권4호
• /
• pp.382-388
• /
• 2016

NiO nanoparticles were synthesized by hydrothermal method for the application to ethanol gas sensor. They were composited with $Co_3O_4$ nanoparticles to improve the sensitivity to ethanol gas. Scanning electron microscopy revealed that the synthesized NiO nanoparticles were plate-shaped with the approximate size and thickness of 60 - 120 nm and 20 nm, respectively. On the other hand, $Co_3O_4$ nanoparticles mixed with NiO was observed to be spherical with the size range of 30 - 50 nm. The sensitivities of NiO sensors composited with $Co_3O_4$ nanoparticles at an optimal ratio of 8 : 2 were enhanced to approximately 1.44 - 1.79 times as high as those of as-synthesized NiO sensors for the ethanol concentration of 10 - 200 ppm at $200^{\circ}C$. The mechanism of the improved ethanol gas sensing of the NiO sensors composited with $Co_3O_4$ nanoparticles was discussed.

• 한국전기전자재료학회논문지
• /
• 제24권7호
• /
• pp.594-598
• /
• 2011

We have investigated the sensing properties of ethanol gas sensor with pure ZnO and Ga-doped ZnO nanowires on Au coated (0001) sapphire substrates grown by hot walled pulsed laser deposition. Randomly aligned ZnO nanowires arrays were grown on a Au-electrode patterned under ambient conditions. ZnO nanowires have various sizes and shapes with a different substrate position inside a furnace. The average of length and diameter of the ZnO nanowires were $8\;{\mu}m$ and 100 nm respectively, and confirmed by field emission scanning electron microscopy. Sensitivity chanege characterization of the gas sensor was found that measured sensitivities of the ethanol gas sensors were 83.3% and 68.3% at $300^{\circ}C$ respectively.

• 한국전기전자재료학회논문지
• /
• 제32권5호
• /
• pp.432-436
• /
• 2019

In this study, we produced a light, flexible, wearable gas sensor by depositing MWCNTs (Multi-walled Carbon Nanotubes) into nylon. MWCNTs are widely used as a gas sensor material due to their excellent mechanical, electrical and physical characteristics. We produced a gas sensor to detect NOx gases by depositing nylon yarn in a MWCNT solution. The MWCNT solution was made by mixing 3 mg MWCNT in 5 ml of ethanol. Nylon yarn was placed in the manufactured solution and ultrasonic waves were applied using an ultrasonicator for 3 h, resulting in MCWNT deposition. The MWCNT-deposited nylon yarn was dried at room temperature for 24 h. The MWCNT-thin-film-coated nylon yarn was masked 1 mm apart, and gold was then deposited on the masked nylon yarn to create the gas sensor. The sensor then was installed in a chamber with a controlled atmospheric environment and exposed to NOx gas. The changing signal from the sensor was amplified to analyze its gas detection characteristics.

• Transactions on Electrical and Electronic Materials
• /
• 제16권6호
• /
• pp.334-337
• /
• 2015

Pure ZnO, ZnO nanowires doped with 3 wt.% Ga (3GZO) and doped with 3 wt.% Ag (3SZO) were grown by a hot-walled pulse laser deposition (HW-PLD) technique. The optical and chemical properties of Ga and Ag doped nanowires was analyzed. Nanowires were determined to be under 200 nm in diameter and several μm in length. Change of significant resistance was observed and the gas detection sensitivities of ZnO, 3GZO and 3SZO nanawires were compared. The sensitivities of ZnO, 3GZO, and 3SZO nanowire sensors were measured at 300℃ for 1 ppm of ethanol gas at 97%, 48%, and 203%, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.483-486
• /
• 2000

In the recognition of the gases using the quartz crystal rnicrobalance (QCM) coated with the film materials, it is important to obtain the recognition ability of gases, and the stability of film coated above the QCM. Especially, the thickness of film coated above the QCM is decreased according with the using circumstance and time of QCM gas sensor. Therefore, the sensing chararcteristics of film is changed with these. In this paper, we coated the lipid GC materials varing with the blended amount of PVC(Po1y Vinyl Chloride) and solution (Tetra Hydrofan:THF) above QCM to obtain the stability of lipid PC film. QCM gas sensors coated with film materials were measured the frequency change in the chamber of stationary gas sensing system injected 1-hexane, ethyl acetate, ethanol and benzene of 20.4 respectively. Also, we measured the degradation characteristics of QCM gas sensor to show the properties of stability.

• 센서학회지
• /
• 제16권1호
• /
• pp.39-43
• /
• 2007

This paper presents characteristics of surface acoustic wave (SAW) gas sensor for detecting volatile gases such as acetone, methanol, and ethanol by measuring phase shift of output signal. A delay-line by combining with a center frequency of 200 MHz was fabricated on S-T Quartz substrates. Using gas chromatography column, the selectivity of the SAW gas sensor were introduced. Experimental results, which show the phase change of output signal under the absorption of volatile gas on sensor surface, were presented. This SAW gas sensor system may be well suited for a high performance electronic nose system.

• 센서학회지
• /
• 제27권4호
• /
• pp.221-226
• /
• 2018

Misfueling accidents significantly damage the engines of both gasoline and diesel vehicles, and should be avoided by rapid and accurate fuel discrimination. Gasoline fuel contains bioethanol. Thus, the detection of ethanol vapor produced by gasoline can be used to distinguish between gasoline and diesel. In the present study, Pt-doped $SnO_2$ hollow nanospheres, Mg-doped $In_2O_3$ hollow microspheres, and Pt-doped ZnO nanostructures have been used as gas sensors to discriminate between gasoline and diesel fuels. All three sensors are able to detect and discriminate between gases evaporating from gasoline and diesel. Among the sensors, the Mg-doped $In_2O_3$ hollow microspheres show a significant gas response (resistance ratio = 4.97) quickly (~3 s) after exposure to gasoline-evaporated gas at $225^{\circ}C$, but did not show any substantial response to diesel-evaporated gas. This demonstrates that gasoline and diesel fuels can be discriminated using small and cost-effective oxide semiconductor gas sensors.