• Transactions of the Society of Information Storage Systems
• /
• v.3 no.3
• /
• pp.118-122
• /
• 2007

Phase-change wet-etching technology using GeSbTe phase-change films is developed. Selective etching between an amorphous and a crystalline phase can be carried out with an alkaline etchant of NaOH. Etching selectivity is dependent not only on the concentration of the alkaline etchant but also on the film structure. Specifically, metal films for heat control cause marked effects on the etching properties of GeSbTe film. Surviving amorphous pits can be obtained with Al metal layer, however etched amorphous pits are seen with Ag metal layer. An opposite selective etching behavior can be observed between samples with two different metal layers.

• Corrosion Science and Technology
• /
• v.10 no.1
• /
• pp.37-42
• /
• 2011

Aluminum was electrochemically etched in acid solution and the surface area was magnified by the formation of etch pits. Etched aluminum was covered with a compact and dense dielectric oxide film by anodization and applied to the aluminum electrolytic capacitor electrode. Capacitance of aluminum electrolytic capacitor is closely related with surface area, which depends on size and number of etch pits. Size of etch pits need to be controlled because inside of the pits can be buried by the formation of dielectric oxide film. In this work, the effect of ultrasound pretreatment on the aluminum etch pit formation and capacitance were investigated. Additionally, the relationship between the second etching effect on pit size and capacitance was studied.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.53-57
• /
• 2014

We describe the preparation of highly-ordered etching pits on the Nb foil through a micromachining. The effects of electrochemical polishing on the formation of uniformly-patterned protective epoxy layer was investigated. Unlike the previous process using $O_2$ plasma, well-ordered etched pits were prepared without any dry processes. As a result, the Nb foil with the well-ordered pits of $10{\mu}m{\times}5{\mu}m$ could be obtained by electrochemical etching in methanolic electrolytes for 10 min.

• Journal of the Korean Ceramic Society
• /
• v.41 no.7
• /
• pp.493-496
• /
• 2004

The chemical etching of sapphire substrates was peformed to produce smooth surfaces on an atomic scale. The sapphire sur-face etched by using a $H_2$S $O_4$ solution showed a pit-free morphology and was yen smooth as much as $\sigma$$_{rms}$=0.13 nm, that etched by using a mixture of $H_2$S $O_4$ and $H_3$P $O_4$ contained large pits with $\sigma$$_{rms}$=0.34 nm. The $\sigma$$_{rms}$’s and the number of the pits increased with increasing etching temperature. The sapphire etched by using $H_2$S $O_4$ at 32$0^{\circ}C$ had the best surface. These results provide important information on the effects of etching treatment on the structural properties of sapphire for the growth of high-quality epilayers.ayers.

• Journal of Korea Foundry Society
• /
• v.25 no.3
• /
• pp.134-141
• /
• 2005

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Al/Fe-17wt%Cr steel(stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemically etched to have optimum pit size and density. The optimum conditions to generate best pit are as follows: Solution: 1 M $Fecl_{3}$+1 M Nacl, Addition: $CuCl_{2}+HCl$, Current density: 80 $mA/cm^{2}$, Total current: 400 $coulomb/cm^{2}$, AC frequency :60 Hz.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.4
• /
• pp.344-349
• /
• 2006

A sublimation epitaxial method, referred to as the Closed Space Technique (CST) was adopted to produce thick SiC epitaxial layers for power device applications. We aimed to systematically investigate the dependence of SiC epilayer quality and growth rate during the sublimation growth using the CST method on various process parameters such as the growth temperature and working pressure. The etched surface of a SiC epitaxial layer grown with low growth rate $(30{\mu}m/h)$ exhibited low etch pit density (EPD) of ${\sim}2000/cm^2$ and a low micropipe density (MPD) of $2/cm^2$. The etched surface of a SiC epitaxial layer grown with high growth rate (above $100{\mu}m/h$) contained a high EPD of ${\sim}3500/cm^2$ and a high MPD of ${\sim}500/cm^2$, which indicates that high growth rate aids the formation of dislocations and micropipes in the epitaxial layer. We also investigated the Schottky barrier diode (SBD) characteristics including a carrier density and depletion layer for Ni/SiC structure and finally proposed a MESFET device fabricated by using selective epilayer process.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.2
• /
• pp.238-244
• /
• 2003

With the purpose of evaluating the effect of ailing amount of pit and assure sealants on the microleakage, 6 groups of specimens with different filling amount, filling materials and surface pretreatment were investigated. Sixty permanent third molars were divided into three groups. The occlusal surface of each tooth was divided into two parts; the filing width of one part was below 1mm (group1, 3, 5), and in the other part more than 2mm (group 2, 4, 6) Group 1 and 2: Helioseal F was applied directly to etched enamel; Group 3 and 4: Helioseal F was applied to etched and scotchbond Multi-purpose plus pre-treated enamel; Group 5 and 6: Tetric Flow was applied. After 500 times thermocycling and dye infiltration, we evaulated the microleakage. The results were as follows; 1. The mean microleakage score at each width were increased in the following order;group 5<3<1, and group 6<4<2. 2. In comparing the groups with same material and surface pretreatment but with different filling width (group 1 versus 2, 3 versus 4, 5 versus 6), the microleakage scores were significantly different. 3 The microleage was affected by filling amount of pit and assure sealants than Oiling materials and dentin bonding agent pretreatment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.338-339
• /
• 2005

The wider surface of the aluminum foil, electrochemically very important and it is necessary to increase the surface area. A study has been made of the fabrication condition for etching cube texture of high purity aluminium foil and of electrochemical etching of the aluminium foil. In the present work, it is shown there exists a relation between the influence of the pre-treatment time in the NaOH & HCI solution and $H_2SO_4$ concentration in the conversion solution. Also effect of temperature during AC etching was also studied. Result of the etched aluminum film is shown in the typical SEM images. Its electrochemical characteristics were investigated by cyclic voltammetry. And effects of current density and frequency is also reported. Cyclic voltammogram showed that the protective oxide film was formedon the inner surfaces of etch pit. the frequency influence resistance of oxide film in AC etching.

• Journal of Korea Foundry Society
• /
• v.19 no.5
• /
• pp.410-418
• /
• 1999

To overcome the undesirable deformation, peeling off and geometrical restrictions which were mainly caused by differences in thermal expansion coefficients during the cladding of aluminum strip and stainless strip, new processing method based on vacuum die casting is designed and implemented in fabricating Fe-17wt%Cr steel (stainless steel). To increase cast-bonding ability, the surface of Fe-17wt%Cr steel is electrochemical etched to have optimum pit size (above 0.2 mm) and pit density (above 30%). The implementation of vacuum die casting by using surface treated stainless steel (Fe-17wt%Cr Steel) produces good trial products having acceptable cast-bonding ability. The enabling conditions for cast-bonding are pouring temperature $690^{\circ}C$, filling speed 30 m/sec and casting pressure $800\;kg/cm^2$. The microscopic observation of cast-bonded Al/Fe-17wt%Cr steel does not show any evidence of intermetallic compounds. The bonding strength of trial products is $150-400\;kg/cm^2$ and this is stronger than conventionally cladded metal having $30-70\;kg/cm^2$.