• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.178.2-178.2
• /
• 2010

The wind turbine gearbox is important rotating part to transmit torque from turbine blade to generator. Generally, gear shaft which rotates causes vibration by influence of stiffness and mass with gear shaft. Root cause of this vibration source is well known to gear transmission error that is decided from gear tooth property. Transmission error excites a gear, and makes excitation force that is vibrated shaft. This vibration of shaft is transmitted to gearbox housing through gearbox bearing. If the resonance about which the natural frequency of the gearbox accords with shaft exciting frequency occurs, a wind turbine can lead to failure. The gearbox for wind turbine should be considered influence of vibration as well as the fatigue life and its performance by such reason. The cause to vibration should be closely examined to reduce influence of such vibration. In this paper, the cause of the vibration which occurs by a gearbox is closely examined and the method which can reduce the vibration which occurred is shown. It is compared with vibration test outcome of a 3MW gearbox for verification of the method shown by this paper.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.111-116
• /
• 2018

This paper introduces the concept of a random universal hash function to amplify security in a quantum key distribution system. It seems to provide security amplification using the relationship between quantum error correction and security. In addition, the approach in terms of security amplification shows that phase error correction offers better security. We explain how the universal hash function enhances security using the BB84 protocol, which is a typical example of QKD(Quantum Key Distribution). Finally, we show that the BB84 protocol using random privacy amplification is safe at higher key rates than Mayers' performance at the same error rate.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.1
• /
• pp.83-91
• /
• 1993

In the digital transmission system, cyclic redundancy check(CRC) code is widely used because it is easy to be implemented and has good performance in error detection. CRC code generator consists of several shift registers and modulo 2 adders. After manipulation of input data stream in the encoder, the remaining value of shift registers becomes CRC code. At the receiving side, error can be detected and corrected by CRC codes immediately transmitted after data stream. But, in the high speed system such as an A TM switch, it is difficult to implement the serial CRC encoder because of speed limitation of available semiconductor devices. In this paper, we propose the efficient parallel CRC encoder and syndrome calculator to solve the speed problem in implementing these functions using the existing semiconductor technology.

• Nuclear Engineering and Technology
• /
• v.41 no.10
• /
• pp.1361-1374
• /
• 2009

Due to the need of data for a Human Reliability Analysis (HRA), a number of data collection efforts have been undertaken in several different organizations. As a part of this effort, a human error analysis that focused on a set of simulator records on a Steam Generator Tube Rupture (SGTR) scenario was performed by using the Human Event Repository and Analysis (HERA) system. This paper summarizes the process and results of the HERA analysis, including discussions about the usability of the HERA system for a human error analysis of simulator data. Five simulated records of an SGTR scenario were analyzed with the HERA analysis process in order to scrutinize the causes and mechanisms of the human related events. From this study, the authors confirmed that the HERA was a serviceable system that can analyze human performance qualitatively from simulator data. It was possible to identify the human related events in the simulator data that affected the system safety not only negatively but also positively. It was also possible to scrutinize the Performance Shaping Factors (PSFs) and the relevant contributory factors with regard to each identified human event.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.668-673
• /
• 2010

Given a periodic reference signal or disturbance, repetitive control is a special control scheme to reduce a tracking error effectively by the periodic signal generator in the repetitive controller. In general, a repetitive controller is added on the existing feedback control system to improve the tracking performance. However, because the information used in the design of the feedback controller is not taken into account, the design problem of the repetitive controller is totally another problem irrespective of that of the feedback controller. In this paper, we present a more general method to design an add-on type repetitive controller using the information on the performance of the existing feedback control system. We first show that a robust stability condition of repetitive control systems is obtained using the well-known robust performance condition of general feedback control systems. It is also shown that we can obtain a steady-state tracking error described in a simple form without time-delay element if the robust stability condition is satisfied for the repetitive control system. From the obtained results, several design criterions for repetitive controller are provided. Through the simulation study, the feasibility of the proposed method is verified.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.746-751
• /
• 2003

A method of measuring the length of defects on the wall of the spent nuclear fuel pool using the image processing and a laser slit beam is proposed. Since the defect monitoring camera is suspended by a crane and hinged to the crane hook, the camera viewing direction can not be adjusted to the orientation that is exactly perpendicular to the wall. Thus, the image taken by the camera, which is horizontally rotated along the axis of the camera supporting beam, is distorted and thus, the precise length can not be measured. In this paper, by using the LASER slit beam generator, the horizontally rotated angle of the camera is estimated. Once the angle is obtained, the distorted image can be easily reconstructed to the image normal to the wall. The estimation algorithm adopts a 3-dimensional coordinate transformation of the image plane where both the laser slit beam and the original image of the defects exist. The estimation equation is obtained by using the information of the beam projected on the wall and the parameters of this equation are experimentally obtained. With this algorithm, the original image of the defect taken at arbitrary rotated angle can be reconstructed to an image normal to the wall. From the result of a series of experiments, the accuracy of the defect is measured within 0.6 and 1.3 % error bound of real defect size in the air and underwater, respectively under 30 degree of the inclined angle of the laser slit beam generator. Also, the error increases as the inclined angle increases upto 60 degree. Over this angle, the defect length can not be measured since the defect image disappears. The proposed algorithm enables the accurate measurement of the defect length only by using a single camera and a laser slit beam.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.504-510
• /
• 2015

Because wind generators (WGs) in a wind power plant (WPP) produce different active powers due to wake effects, the reactive power capability of each WG is different. This paper proposes a hierarchical voltage control scheme for a WPP that uses a WPP controller and WG controller. In the proposed scheme, the WPP controller determines a voltage error signal by using a PI controller and sends it to a doubly-fed induction generator (DFIG). Based on the reactive current-voltage ($I_Q-V$) characteristic of a DFIG, the DFIG injects an appropriate reactive power corresponding to the voltage error signal. To enhance the voltage recovery capability, the gains of the $I_Q-V$ characteristic of a DFIG are modified depending on its reactive current capability so that a DFIG with greater reactive current capability may inject more reactive power. The proposed scheme enables the WPP to recover the voltage at the point of common coupling (PCC) to the nominal value within a short time after a disturbance by using the adaptive $I_Q-V$ characteristics of a DFIG. The performance of the proposed scheme was investigated for a 100 MW WPP consisting of 20 units of 5 MW DFIGs for small and larger disturbances. The results show the proposed scheme successfully recovers the PCC voltage within a short time after a disturbance.

• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.902-908
• /
• 2009

TETRA is the standard of Digital Trunked Radio System developed by the ETSI (European Telecommunications Standards Institute). It is currently adopted as Electric Power IT Wireless Backbone Network in Korea, and a national enterprise is going on for versatile utilization of TETRA. To use TETRA wireless network, TETRA modem is very necessary such that performance measurements are very crucial for each TETRA modem by various manufacturers. In this paper, PED (Protocol Evaluation Data) is suggested for PD performance measurement in D-TRS wireless network environment. The performance measurements for different data lengths and transmission intervals are done using TG (Traffic Generator) on Test Bed. The data size is increased by 10 bytes from 10-byte to 400-byte, and it is measured 1,000 times for each transmission interval of 0.5, 1.0, and 1.5 seconds. Based on the transmission time measured, average transmission speed and MER (Message Error Rate) are derived for TETRA Modem performance measurement. Two TMR880i's of EADS are used for TETRA modem, and SwMI (Switching and Management Infrastructure) of EADS is used for switching system in this paper.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.23-29
• /
• 2011

A dB-linearity improved variable gain amplifier (VGA) for GPS receiver is presented. The Proposed dB-linear current generator has improved dB-linearity error of ${\pm}0.15$dB. The VGA for GPS is designed using proposed dB-linear current generator and composed of 3 stage amplifiers. The IF frequency is assumed as 4MHz and the linearity requirement of the VGA for GPS receiver is defined as 24dBm of IIP3 using cascaded IIP3 equation and the VGA satisfies 24dBm when minimum gain mode. The DC-offset voltage is eliminated using DC-offset cancelation loop. The gain range is from -8dB to 52dB and the dB-linearity error satisfies ${\pm}0.2$dB. The 3-dB frequency has range of 35MHz~106MHz for the gain range. The VGA is designed using 0.18${\mu}m$ CMOS process. The power consumption is 3mW with 1.8V supply voltage.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.