• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.122-127
• /
• 2008

The source of wayside noise for the train are the aerodynamic noise, wheel/rail noise, and power unit noise. The major source of railway noise is the wheel/rail noise caused by the interaction between the wheels and rails. The Structure borne noise is mainly a low frequency problem. The train noise and vibration nearby the elevated railway make one specific issue. The microphone array method is used to search sound radiation characteristics of elevated structure to predict the noise propagation from an elevated railway. In this paper, the train noise and structure borne noise by train are measured. From the results, we investigated the effect on the sound absorption tunnel for elevated railway.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.344-349
• /
• 2005

Neutron count rate measurements to assay fissile content of uranium powder have been carried out in a neutron counter. The induced fission neutrons by Cf-252 neutron source are counted as the variation of fissile material in fuel material. The measured counts are compared with equivalent results obtained from calculation. It shows that the measured neutron counts versus quantity of $UO_2$ powder enrichment agreed reasonably well with the calculated values.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.5
• /
• pp.479-488
• /
• 1991

A novel three-phase quasi-resonant dc link inverter (QRI)with a switch connected between dc voltage source and resonant inductor is proposed. According to the state of switching and load current, the operating mode of the proposed inverter scheme is classified into free-wheeling, inverting, and rectifying mode. By examining the behavior of the circuit in each operating mode, an equivalent circuit which represents all the modes in a unified manner is derived. The operating principle of QRI at inverting mode is analyzed, and it is shown that the maximum voltage of resonant dc link is confined to twice the dc source voltage and that both the zero voltage switching of inverter and the zero current switching of inserted switch are guaranteed. An appropriate current control algorithm is suggested, and the opeating characteristics of proposed resonant inverter are verified through both simulation and experiment.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.253-258
• /
• 2007

Guss asphalt used in pavement of a steel deck bridge may cause severe stress and displacement on the bridge as it is treated using very high temperatures ranging from $220^{\circ}C$ to $260^{\circ}C$. Therefore, it is critical to estimate the thermal effect of Guss asphalt on the steel deck bridge before the width and pattern of the unit portion are decided to minimize impact. In this study, introduce a new analysis method styled the Heat source of equivalent of the cable stayed bridge were conducted to verify the feasibility of numerical value analysis by comparing the results with the data measured. The thermal effects of Guss asphalt on the steel deck bridge according to temperature changes were also studied.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.3 no.1
• /
• pp.32-36
• /
• 2003

An equivalent schema matching among several different source schemas is very important for information integration or mining on the XML based World Wide Web. Finding most similar source schema corresponding mediated schema is a major bottleneck because of the arbitrary nesting property and hierarchical structures of XML DTD schemas. It is complex and both very labor intensive and error prune job. In this paper, we present the first complex matching of XML schema, i.e. XML DTD. The proposed method captures not only schematic information but also integrity constraints information of DTD to match different structured DTD. We show the integrity constraints based hierarchical schema matching is more semantic than the schema matching only to use schematic information and stored data.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.509-512
• /
• 1995

The relaying algorithm to calculate the fault distance from only transient signal at faults in T/L is presented. In this paper. At faults the oscillation frequency components exist in both voltage and current and these components minimize the input impedance shown in fault point. The equivalent source impedance shown in relaying point is needed to calculate the fault distance using these components. To source impedance, the reflection coefficient between forward wave and backward and the Prony's analysis is also employed to extract the oscillation frequency component from transient signals. The case study show that the new distance relaying algorithm satisfies the high operation speed and high accuracy even if the algorithm uses only transient signals.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1856-1858
• /
• 2000

This paper describes the principles of reignition system which has newly been developed and used as KERI's high power testing facilities. Synthetic short-circuit testing method is generally adopted to perform the short-circuit test of the ultra high-voltage circuit breakers, which consists of two separated sources such as the current source from short-circuit generator and the voltage source from charged energy in capacitor. And, in case of synthetic short-circuit test, it will be necessary to use the reignition system in order to extending the arcing time of the circuit breaker and provide the arc energy equivalent to the direct testing method.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.5C no.3
• /
• pp.124-130
• /
• 2005

In this paper, we designed a cylindrical type light source having an electromagnetic principle of inductively coupled plasma, and measured its electrical-optical properties. Using the transformer principle, an electrically equivalent circuit cylindrical type light source was analyzed. According to the parameters of electromagnetic induction, which were diameter of coil with cpO.3$\~$ 1.2mm, number of turns with 4$\~$ 12 turns, distance with 40$\~$ l20mm and RF power with 10$\~$ 150W, the electrical .md optical properties were measured. When the diameter of the coil was cp0.3mm, number of turns was 8 and distance was 40mm, and the maximum brightness of 29,730 cd/m$^{2}$ was shown with RF power l50W. The relationship between electromagnetic induction and plasma discharges was demonstrated using the mode transition from E-mode to H-mode

• The Transactions of the Korean Institute of Power Electronics
• /
• v.2 no.1
• /
• pp.1-11
• /
• 1997

In this paper, a novel multivariable state feedback control with feedforward control is proposed to improve control performance of power conversion systems. The targets of the application are three-phase voltage-source PWM converter and inverter system, and current-source PWM converter and inverter system, of which equivalent circuits and models are derived and analyzed. Various simulation results are presented to verify the validity of the proposed scheme.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.209-215
• /
• 2004

This paper presents the frequency range and an analysis method to find the dominant source of electro-magnetic wave which originates from a spark ignition in engine room. Applying the distributed constant equivalent circuit theory the radiation of probable electro-magnetic wave around an ignition plug and a high voltage cable is studied analytically. Experimental studies are also conducted by measuring the frequency spectrum to obtain the radiating characteristics of electro-magnetic wave. Results from both analytical and experimental studies confirm that an ignition plug and a high voltage cable are dominant sources of electro-magnetic wave and that the radiating frequency is ranged from 1.3[GHz] to 2[GHz] band.