• 자원ㆍ환경경제연구
• /
• 제15권3호
• /
• pp.505-530
• /
• 2006

열병합발전은 에너지사용의 효율적인 기술로서 고유가의 지속 및 이산화탄소 배출저감에 대한 국제적인 압력의 강화, 분산열원 또는 분산전원의 개발 필요성의 증대 등으로 인하여 정부와 사업자들로부터 관심이 높다. 따라서 지역냉난방사업을 추진할 경우, CHP가 경제적인 관점에서 도입될 수 있는지, 도입된다면 적정 규모는 어느 정도인지가 연구대상이 된다. 본 연구는 실제 지역냉난방사업에 활용할 수 있는 설비선택에 관한 수리계획 모형을 설정하고 이를 실증적으로 분석하였다. 분석모형은 열원의 종류와 규모, 이들의 가동수준 그리고 투입연료의 양 등을 주요 결정변수로 하고 있다. 모형은 모든 종류의 설비(열병합발전기, 열전용보일러, 냉열생산 설비, 축열조 등)를 모형에 포함시켜 선택 가능하도록 구성하였다. 모형의 주요 특징은 변동 열전비 열병합발전의 운전모드도 하나의 기술로 간주하여 모형에서 이를 선택하게 할 수 있으며, 특정지역에 대한 CHP와 열전용 보일러의 용량에 대한 적정 구성비도 도출할 수 있다. 본 연구는 기업측면에서는 설비최적화 모델로 활용할 수 있으며, 규제자의 측면에서는 설비규모 인허가에 참고자료로 활용 가능할 것이다.

• 한국전산유체공학회지
• /
• 제13권4호
• /
• pp.1-7
• /
• 2008

In the process of continuous hot-dip galvanizing, it is well known that the gas wiping through an air knife system is most effective because of its uniformity in coating thickness, possibility of thin coating, workability in high speed, and simplicity of control. However, gas wiping used in the galvanizing process brings about a problem of splashing at the strip edge above a certain high speed of process. It is also known that the problem of edge splashing is more harmful than that at the mid strip surface. For a given liquid(of a certain viscosity and surface tension), the onset of splashing mainly depends upon the strip velocity, the gas-jet pressure, and the nozzle's stand-off distance. In these connections in the present study, we proposed three kinds of air knife system having nozzles of constant expansion rate, and compared the jet structures issuing from newly proposed nozzle systems with the result by a conventional one. In numerical analysis, the governing equations are consisted of two-dimensional time dependent Navier-Stokes equations, and the standard k-${\varepsilon}$ turbulence model is employed to solve turbulence stress and so on. As the result, it is found that we had better use the constant expansion-rate nozzle which can be interpreted from the point view of the energy saving for the same coating thickness. Also, we better reduce the size of separation bubble and enhance the cutting ability at the strip surface, by using an air-knife having constant expansion-rate nozzle.

• ETRI Journal
• /
• 제42권4호
• /
• pp.596-607
• /
• 2020

Scaling is an important operation because of the iterative nature of arithmetic processes in digital signal processors (DSPs). In residue number system (RNS)-based DSPs, scaling represents a performance bottleneck based on the complexity of intermodulo operations. To design an efficient RNS scaler for special moduli sets, a body of literature has been dedicated to the study of the well-known moduli sets {2ⁿ - 1, 2ⁿ, 2ⁿ + 1} and {2ⁿ, 2ⁿ - 1, 2ⁿ⁺¹ - 1}, and their extension in vertical or horizontal forms. In this study, we propose an efficient programmable RNS scaler for the arithmetic-friendly moduli set {2^n+p, 2ⁿ - 1, 2ⁿ⁺¹ - 1}. The proposed algorithm yields high speed and energy-efficient realization of an RNS programmable scaler based on the effective exploitation of the mixed-radix representation, parallelism, and a hardware sharing technique. Experimental results obtained for a 130 nm CMOS ASIC technology demonstrate the superiority of the proposed programmable scaler compared to the only available and highly effective hybrid programmable scaler for an identical moduli set. The proposed scaler provides 43.28% less power consumption, 33.27% faster execution, and 28.55% more area saving on average compared to the hybrid programmable scaler.

• KIEAE Journal
• /
• 제1권2호
• /
• pp.5-12
• /
• 2001

Through the harmony of natural and artificial systems a city is composed of, the ecology-oriented urban planning seeks for qualitative improvements of a city on which our life is based. To enhance the ecology-oriented urban planning, the followings are suggested by a comparative analysis of Korea with Germany regarding the development process, the instruments, and the establishment of indicators for the planning. Firstly, though our national land development plan is closely connected with B-plan, it has little to do with the natural environment. Moreover, the natural environment plan of the Ministry of Environment is almost impossible to carry out in terms of urban construction work. For this reason, the instrument for dealing with the development and environment plan systems together as well as the completion of the current plan system is needed for the ecologically acceptable urban development in the long term. Secondly, in order to realize what is mentioned above in the concrete it seems to be desirable for the system and the instrument to be devised at the extent of B-plan. The regulations of the plan should have strong legal binding force and practicality as well. The element of ecology-oriented urban planning are (1) degree of independence and appropriate density, (2) conservation of natural elements such as soil, water, animals and plants etc., (3) energy saving in land use, (4) activation of B-plan and inducement of active participation of residents. Thirdly, it will be useful to develop various kinds of indicators for the environment plan provided in advance so that the ecology-oriented urban developments may be under control. It also should be taken into consideration that the indicators are supposed to be comprehensive, representative, and practical enough to make the most of at the early stage of drawing up a plan. The kinds of indicators which can be used in the ecology-oriented urban development include (1) soil, (2) water, (3) vegetation and plants, (4) animals, (5) climate, and (6) transportation.

• 한국정보전자통신기술학회논문지
• /
• 제10권1호
• /
• pp.23-30
• /
• 2017

현재는 도로조명의 경우 기존 메탈할라이드 램프 400W이하로 설치되어 있어 에너지절약형 조명으로 대체가 이루어지고 있으며, 무전극 램프는 터널조명과 고천정조명 적용분야를 타겟으로 더욱 활발한 교체가 이루어질 것으로 예상된다. 따라서 추가적으로 고효율, 고출력 무전극 램프 시스템 개발이 필요한 상황이다. 본 연구에서는 고출력 무전극 램프의 설계 및 제작을 진행하여 가스종류 및 가스압에 따른 비교 분석, 아말감 종류에 따른 특성 분석 등을 통한 무전극 램프 최적화를 진행하였다. 현재 고출력 무전극 램프 방전관 및 페라이트코어에 맞는 가스압 300~350[mmHg] 사이로 최적화 하였다. 인듐(In) 아말감을 적용한 무전극 램프로 점등회로 매칭을 완료하여 250W(정격${\pm}10%$)로 정격소비전력으로 최적화를 완료하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권5호
• /
• pp.12-23
• /
• 1994

The two-phase flow is observed in power plants, chemical process plants, and refrigeration systems etc., and it is very important to solve the heat transfer mechanism of a boiler, an automic reactor, a condenser and various types of evaporators. Recently, the problem of two phase heat transfer is braught up in many regions with development of energy saving technique. In flow boiling system it is necessary to store data in each condition because the heat transfer characteristics of flow boiling region vary by the change of flow pattern and the magnetude of heat flux to tube length, and be subtly affected by the flow and heating condition. So basic study for knowing flow pattern in heat transfer region and the relation between heat transfer characteristic and flow condition is desired to accumulate data in wide variety of liquid and flow system in the study of heat transfer of two phase flow. In this study R-113 was selected as working fluid whose properties were programmed by least square method, and experiment was conducted in the region of mass flow $1.628{\times}10^6$~$4.884{\times}10^6$/kg/$m^2$hr with inlet subcooling 10~3$0^{\circ}C$, sustaining test section inlet pressure to 1.5kg$_f$/$cm^2$abs.

• 한국산업융합학회 논문집
• /
• 제9권1호
• /
• pp.61-66
• /
• 2006

In perspective of saving natural resource and energy, today's automobiles are in process of regenerating by smaller and lighter. In order to achieve the sufficiency on the consumption of the fuel, new mechanism and new assembly are required. Therefore the expectations on the new materials are very high. Especially, AI materials are widely used to reduce the weight. AI that is used in automobiles is mostly casting material, and according to the innovation of technique is in rapid development. AI Die casting is an important field as today's trend of lightweight on automobiles. One of the parts in steering system, Valve Housing plays a role of reduce the operating effort of drivers. Unfortunately, the Valve Housing which is widely reliable to the most automobiles are not developed at this moment in our automobile industry. Therefore, they are produced by casting method which cost three times or even more expensive in production. If Valve Housing, which is a part of steering system is produced by Gravity Casting, the space that manufacturing equipment will be increased, and more time and workers would be brought into service. For such reason, Die Casting would replace Gravity Casting in order to minimize cost of time, manpower, and working space.

• 한국인터넷방송통신학회논문지
• /
• 제18권1호
• /
• pp.29-35
• /
• 2018

최근 어린이집에서 안전사고가 빈번하게 발생하고 있다. 유형별로는 부딪힘, 넘어짐, 끼임, 화상, 떨어짐, 통학버스 교통사고, 이물질 삽입... 등이 있으며, 이러한 안전사고 즉, 재난으로 인해 사망까지 이르는 영유아들이 매년 꾸준히 증가하는 추세이다. 이에 따라 안전사고, 즉 재난에 대한 예방이 시급한 실정이다. IoT(Internet of Things)는 위험을 예방하기 위해서 다양한 센서와 관련제품들이 생활공간에서 인터넷으로 연결해 관리되고 있다. 특허 IoT 제품은 언제 어디서든 스마트폰이나 센서 등으로 자동 제어하기 때문에 에너지와 시간을 아끼고, 편리하고 신속 정확하게 지킬 수 있다. 이 논문은 학습현장 즉, 학교나 유치원 및 어린이집과 같은 곳에서 건물재난관리를 위한 사물인터넷 전용망인 SK LoRa 통신망과 아두이노를 이용하여 재난에 대응하고 예방할 수 있는 연구 모델을 제안하고자 한다. 그리고 건물재난관리에 필요한 다양한 센서로 건물 내 다양한 안전 상태를 표현하고 데이터는 스마트폰으로 송수신하여 주거환경을 제어할 수 있는 시스템 모델을 제안한다.

• 대한기계학회논문집A
• /
• 제25권5호
• /
• pp.805-815
• /
• 2001

Glaucoma is an eye disease which is caused by abnormal high IOP (Intra Ocular Pressure). High IOP is caused by the aqueous humor which is produced consistently but not drained due to malfunction of the trabecular system which has a role of draining the aqueous humor into the venous system. Currently, there are three methods to treat glaucoma-using medicines, surgical operation, and using implant device. The first and second methods are not long acting, so the use of implants is increasing in these days in order to drain out the aqueous humor compulsory. However, though conventional implants have a capability of pressure regulation, they cannot maintain IOPs desired for different patients, and too much aqueous humor are usually drained, to cause hypotony. To solve these problems, it is needed to develop a new implant which is capable of controling the IOP actively and copes with personal difference of patients. An active glaucoma implant consists of the valve actuator, pressure sensor, controller, and power supply. In this paper, firstly, we make an analysis of the operation of a conventional implant using a bond graph and show defects and limitations of the conventional valve analytically. Secondly, we design and analyze a valve actuator considering actuation principles, resistance elements, control methods, and energy sources focused on power saving problem. Finally, using simulations the possibility of the proposed valve actuator is investigated.

• 한국염색가공학회지
• /
• 제8권5호
• /
• pp.7-16
• /
• 1996

The air-flow dyeing machine is a new type of dyeing machine. Which is an energy saving type to be able to dye the fabrics with the lowest liquor ratio and in shorter time. This machine is operated with an aerodynamic system rather than a hyd raulic system for traditional jet or overflow dyeing. An air-flow dyeing machine(Green-flow) by the use of aerodynamic technology was developed and compared with the Luft-roto machine made by Thies Company, Germany, in this study. Three samples were dyed with both machines under the same dyeing conditions and color fastness, dyeing levelness, drapability, and mechanical properties of these samples were compared. The results were as follows; Both machines have almost the same dyeability. The dyeability was good at liquor ratio of 1: 3.5 and the speed of 450yds/min. The order for drapability was Crepe de Chine > Cool Peach > Charmeuse. Except for the color fastness of sublimation being below class 4, most color fastness of samples dyed with Green-flow m/c were above class 4. The maximum speed was 510yds/min. for Crepe de Chine and the standard deviation of K/S value was lower for Charmeuse and Cool Peach when employed on the "Green-flow" machine and lower for Crepe de Chine when employed on the Luft-roto machine. Comparing with dyeing of the Green-flow machine and that of the Luft-roto machine, the RT of the Charmeuse was found to be higher with the Green-flow machine and thus the sample had an improved wrinkle recovery. LT and WT of Cool Peach were higher, and shear properties(G, 2HG, 2HGS) of Crepe de Chine were higher, both turning out as suitable for clothing. clothing.