• Resources Recycling
• /
• v.25 no.4
• /
• pp.23-31
• /
• 2016

It was found that there was no problem in recycling by-products (waste rock and tailings) from Yangyang iron mine themselves through matter conversion because they are not hazardous according to results of KSLT method. In case of using tailings as sub-materials of cement, it recommended the use of less than 3% tailings dosage not to exceed 0.6% of total alkali ($R_2O$) content based on standard quality of portland cement (KS L 5201). Non sintered eco-brick corresponding to class 1 quality of recycled clay brick (KS I 3013) can replace 15% of cement with tailings and 100% of general fine aggregate with waste rock from iron mine. As mentioned above, recycling the by-products (waste rock and tailings) as sub-materials of cement and non sintered eco-brick could gain both environmental and economic benefits, that is, reduction of scale and maintenance cost of tailing ponds, decrease of energy use and $CO_2$ emission.

• Tunnel and Underground Space
• /
• v.25 no.5
• /
• pp.435-449
• /
• 2015

Physical and microstructural properties of Pungchon and Maggol limestone were investigated quantitatively during 50 cycles of artificial freezing and thawing test. There were decrease in dry weight and P,S-wave velocity, and increase in absorption rate in both rock types. Porosity, pore volume, equivalent diameter, throat thickness and pore orientation were analyzed using X-ray computed tomography images. Porosity increased, and initiation and expansion of pores were investigated as weathering progresses. Physical and microstructural variation in Maggol limestone was larger than that of Pungchon limestone because Maggol limestone has more pores and microcracks at initial state. As this study analyzes physical and microstructural properties of rock specimens comprehensively, it can be applied to further rock weathering study and can be used as fundamental data of construction and resource development in cold regions.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.1
• /
• pp.61-66
• /
• 2006

In perspective of saving natural resource and energy, today's automobiles are in process of regenerating by smaller and lighter. In order to achieve the sufficiency on the consumption of the fuel, new mechanism and new assembly are required. Therefore the expectations on the new materials are very high. Especially, AI materials are widely used to reduce the weight. AI that is used in automobiles is mostly casting material, and according to the innovation of technique is in rapid development. AI Die casting is an important field as today's trend of lightweight on automobiles. One of the parts in steering system, Valve Housing plays a role of reduce the operating effort of drivers. Unfortunately, the Valve Housing which is widely reliable to the most automobiles are not developed at this moment in our automobile industry. Therefore, they are produced by casting method which cost three times or even more expensive in production. If Valve Housing, which is a part of steering system is produced by Gravity Casting, the space that manufacturing equipment will be increased, and more time and workers would be brought into service. For such reason, Die Casting would replace Gravity Casting in order to minimize cost of time, manpower, and working space.

• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.1
• /
• pp.116-123
• /
• 2003

Forages are the most important feed resource for ruminants worldwide, whether fed as pastures, forage crops or conserved hay, silage or haylage. There is large variability in the quality of forages so measurement and prediction of feeding value and nutritive value are essential for high levels of production. Within a commercial animal production system, methods of prediction must be inexpensive and rapid. At least 50% of the variation in feeding value of forages is due to variation in voluntary feed intake. Identification of the factors that constrain voluntary feed intake allows these differences to be managed and exploited in forage selection. Constraints to intake have been predicted using combinations of metabolic and physical factors within the animal while simple measurements such as the energy required to shear the plant material are related to constraints to intake with some plant material. Animals respond to both pre- and post-ingestive feedback signals from forages. Pre-ingestive signals may play a role in intake with signals including taste, odour and texture together with learned aversions to nutrients or toxins (post-ingestive feedback signals). The challenge to forage evaluation is identification of the factors which are most important contributors to these feedback signals. Empirical models incorporating chemical composition are also widely used. The models tend to be useful within the ranges of the datasets used in their development but none can claim to have universal application. Mechanistic models are becoming increasingly complex and sophisticated and incorporate both feed characteristics and use of biochemical pathways within the animal. Improvement in utilisation through the deliberate selection of pasture plants for high feeding value appears to have potential and has been poorly exploited. Use of Near Infrared Reflectance Spectroscopy is a simple method that offers significant potential for the preliminary screening of plants with genetic differences in feeding value. Near Infrared Reflectance Spectroscopy will only be as reliable as the calibration sets from which the equations are generated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.302-307
• /
• 2017

Draft ice in polar regions is formed due to sea level changes and various environmental factors cause damage due to collision with offshore plants and ships for resource development. Drift ice in polar regions is a potential source of accidents for offshore plants that perform long-term operations in one place, as well as on the ship. To prevent accidents with drift ice, offshore plants and ships in polar regions use satellite image information and detection radar to detect drift ice. However, the inability to use visible satellite images at night significantly lowers the detection probability by radar for small drift ice. In this study, we used a thermal imaging system which can be operated day and night for the detection of drift ice, and carried out an experimental study on the detection characteristics of drift ice. To examine the night operation of the thermal imaging system, the experimental condition was set and the thermal image was measured according to the measurement angle change. Under this condition, the correlation was analyzed by theoretical calculating the radiant energy of the drift ice and the sea water.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.2
• /
• pp.58-66
• /
• 2012

Brewers grain is a byproduct of beer brewing and consists primarily of grain husks, pericarp, and fragments of endosperm. Although this material is consumed by animals and used as fertilizer, a large amount of brewers grain is simply discarded. Therefore, new methods for utilizing this fibrous resource should be pursued. In this study, we examined the potential utilization of brewers grain as an additive in the paperboard industry by determining the chemical composition of brewers grain and the physical properties of brewers grain powders after grinding with two types of grinders. We found that brewers grain had a lower holocellulose content and higher lignin content and intermediate ash content when compared to other biomass materials, and did not contain any contaminants that would interfere with the papermaking process. Particles had a higher fiber length, less fiber width, and narrower shape factor distribution when ground by a blender type grinder than by a pin crusher type grinder. The blender type grinder was concluded to make regular brewers grain particles appropriate for papermaking.

• The Korean Journal of Applied Statistics
• /
• v.32 no.5
• /
• pp.703-720
• /
• 2019

The influence of temperature on electricity demand is increasing due to extreme weather and climate change, and the climate impacts involves nonlinearity, asymmetry and complexity. Considering changes in government energy policy and the development of the fourth industrial revolution, it is important to assess the climate effect more accurately for stable management of electricity supply and demand. This study aims to analyze the effect of temperature change on electricity demand using the partial linear model. The main results obtained using the time-unit high frequency data for meteorological variables and electricity consumption are as follows. Estimation results show that the relationship between temperature change and electricity demand involves complexity, nonlinearity and asymmetry, which reflects the nonlinear effect of extreme weather. The prediction accuracy of in-sample and out-of-sample electricity forecasting using the partial linear model evidences better predictive accuracy than the conventional model based on the heating and cooling degree days. Diebold-Mariano test confirms significance of the predictive accuracy of the partial linear model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.6
• /
• pp.603-611
• /
• 2016

Research and development of mineral-resource-related products has progressed with the increased need to develop mineral resources. The DTH hammer is a resultant product. However, owing to particular work conditions of underground drilling, it is difficult to obtain direct data on the DTH hammer. A DTH drill rig requires a significant amount of money and time for actual testing. This thesis aimed to resolve this problem by using CAE. In a previous paper, the structure of the DTH hammer and its movement were analyzed, and a standard model based on simulation was proposed. Then, experimentation and comparison verification were conducted. In this paper, by using an experimental design method, we derived a control factor of the impact force and efficiency of the DTH hammer and attempted to optimize the design. As a result, the impact energy increased by 14.9%, and the efficiency increased by 3.3%.

• International Journal of Advanced Culture Technology
• /
• v.3 no.2
• /
• pp.100-109
• /
• 2015

Environmental problems from petroleum-based plastic wastes have been rapidly increasing in recent years. The alternative solution is focus on the development of environmental friendly plastic derived from renewable resource. Poly(lactic acid) (PLA) is a biodegradable polymer synthesized from biomass having potential to replace the petroleum-based non-degradable polymers utilizations. PLA can be synthesized by two methods: (1) ring-opening of lactide intermediate and (2) direct polycondensation of lactic acid processes. The latter process has advantages on high yields and high purity of polymer products, materials handling and ease of process treatments. The polymerization process of PLA synthesis has been widely studied in a laboratory scale. However, the mass scale production using direct polycondensation of lactic acid has not been reported. We have investigated the kinetics and scale-up process of direct polycondensation method to produce PLA in a pilot scale. The order of reaction is 2 and activation energy of lactic acid to lactic acid oligomers is 61.58 kJ/mol. The pre-polymer was further polymerized in a solid state polymerization (SSP) process. The synthesized PLA from both the laboratory and pilot scales show the comparable properties such as melting temperature and molecular weight. The appearance of synthesized PLA is yellow-white solid powder.

• Industry Promotion Research
• /
• v.1 no.1
• /
• pp.143-149
• /
• 2016

This study verified the relationship on the perception of water reuse R&D support and water reuse vitalization policy. The study results showed that the perception of water reuse importance and effectiveness positively affected the perception of the necessity of water reuse vitalization policy, necessity of supporting water reuse water-saving product company, necessity of investing water reuse(p<.001). Also, gender, education, occupation, type of residence and monthly water rate significantly affected the between-group differences of the perception of water reuse vitalization policy. This study provided implications for preparing water reuse investment and vitalization policy by the relationship on the perception of water reuse R&D support and water reuse vitalization policy.