• 한국전기전자재료학회논문지
• /
• 제35권6호
• /
• pp.594-602
• /
• 2022

Cast-resin transformers are widely installed in various electrical power systems because of their low operating cost and low influence on external environmental factors. However, when they have an internal defect during the manufacturing process or operation, a partial discharge (PD) occurs, and eventually destroys the insulation. In this paper, a Rogowski-type PD sensor was studied to replace commercial PD sensors used for the insulation diagnosis of power apparatus. The proposed PD sensor was manufactured with four different types of PCB-based winding structures, and it was analyzed in terms of the detection characteristics for standard calibration pulses and the changes of the output voltage according to the distance. The output increased linearly in accordance with the applied discharge amount. It was confirmed that the hexagon structure sensor had the highest sensitivity, because the winding cross-sectional area of the sensor was larger than others. In addition, as the distance from the defect increased, the output voltage of the sensors decreased by 7.32% on average. It was also confirmed that the attenuation rate according to the distance decreased as the input discharge amount increased. For the application of this new type sensor, PD electrode system was designed to simulate the void defect. Waveforms and PRPD patterns measured by the proposed PD sensors at DIV and 120% of DIV were the same as the results measured by MPD 600 based on IEC 60270. The proposed PD sensors can be installed on the inner wall of the transformer tank by coating its surfaces with a non-conductive material; therefore, it is possible to detect internal defects more effectively at a closer distance from the defect than the conventional sensors.

• 한국전기전자재료학회논문지
• /
• 제36권5호
• /
• pp.423-432
• /
• 2023

With the increasing demand for mobile devices featuring multi-touch operation, extensive research is being conducted on touch screen panel (TSP) Readout ICs (ROICs) that should possess low power consumption, compact chip size, and immunity to external noise. Therefore, this paper discusses capacitive touch sensors and their readout circuits, and it introduces research trends in various circuit designs that are robust against external noise sources. The recent state-of-the-art TSP ROICs have primarily focused on minimizing the impact of parasitic capacitance (Cp) caused by thin panel thickness. The large Cp can be effectively compensated using an area-efficient current compensator and Current Conveyor (CC), while a display noise reduction scheme utilizing a noise-antenna (NA) electrode significantly improves the signal-to-noise ratio (SNR). Based on these achievements, it is expected that future TSP ROICs will be capable of stable operation with thinner and flexible Touch Screen Panels (TSPs).

• The Korean Journal of Pain
• /
• 제36권4호
• /
• pp.465-472
• /
• 2023

Background: Percutaneous radiofrequency thermocoagulation (RFTC) has been widely utilized in the management of trigeminal neuralgia. Despite using image guidance, accurate needle positioning into the target area still remains a critical element for achieving a successful outcome. This study was performed to precisely clarify the anatomical information required to ensure that the electrode tip is placed on the sensory component of the mandibular nerve (MN) at the foramen ovale (FO) level. Methods: The study used 50 hemi-half heads from 26 South Korean adult cadavers. Results: The cross-sectioned anterior and posterior divisions of the MN at the FO level could be distinguished based on an irregular boundary and color difference. The anterior division was clearly brighter than the posterior one. The anterior division of the MN at the FO level was located at the whole anterior (38.0%), anteromedial (6.0%), anterior center (8.0%), and anterolateral (22.0%) parts. The posterior division was often located at the whole posterior or posterolateral parts of the MN at the FO level. The anterior divisions covered the whole MN except for the medial half of the posterolateral part in the overwrapped images of the cross-sectional areas of the MN at the FO level. The cross-sectional areas of the anterior divisions were similar in males and females, whereas those of the posterior divisions were significantly larger in males (P = 0.004). Conclusions: The obtained anatomical information is expected to help physicians reduce unwanted side effects after percutaneous RFTC within the FO for the MN.

• 한국수소및신에너지학회논문집
• /
• 제33권6호
• /
• pp.723-732
• /
• 2022

Cracking ammonia inside solid oxide fuel cell (SOFC) stack is a compact and simple way. To prevent sharp temperature fluctuation and increase cell efficiency, the decomposition reaction should be spread on whole cell area. This leading to a question that, how does anode thickness affect the conversion rate of ammonia and the cell voltage? Since the 0D model of SOFC is useful for system level simulation, how accurate is it to use equilibrium solver for internal ammonia cracking reaction? The 1D model of ammonia fed SOFC was used to simulate the diffusion and reaction of ammonia inside the anode electrode, then the partial pressure of hydrogen and steam at triple phase boundary was used for cell voltage calculation. The result shows that, the ammonia conversion rate increases and reaches saturated value as anode thickness increase, and the saturated thickness is bigger for lower operating temperature. The similar cell voltage between 1D and 0D models can be reached with NH₃ conversion rate above 90%. The 0D model and 1D model of SOFC showed similar conversion rate at temperature over 750℃.

• 신재생에너지
• /
• 제18권1호
• /
• pp.29-34
• /
• 2022

The most prevalent cause of solar cell efficiency loss is reduced recombination at the metal electrode and silicon junction. To boost efficiency, a a SiO_X/poly-Si passivating interface is being developed. Poly-Si for passivating contact is formed by various deposition methods (sputtering, PECVD, LPCVD, HWCVD) where the ploy-Si characterization depends on the deposition method. The sputtering process forms a dense Si film at a low deposition rate of 2.6 nm/min and develops a low passivation characteristic of 690 mV. The PECVD process offers a deposition rate of 28 nm/min with satisfactory passivation characteristics. The LPCVD process is the slowest with a deposition rate of 1.4 nm/min, and can prevent blistering if deposited at high temperatures. The HWCVD process has the fastest deposition rate at 150 nm/min with excellent passivation characteristics. However, the uniformity of the deposited film decreases as the area increases. Also, the best passivation characteristics are obtained at high doping. Thus, it is necessary to optimize the doping process depending on the deposition method.

• Advances in nano research
• /
• 제15권1호
• /
• pp.1-13
• /
• 2023

Ti₃C₂T_x MXene, a 2D material, is known to exhibit unique characteristics that are strongly dependent on surface termination groups. Here, we developed a novel annealing approach with Ca as a reducing agent to simultaneously remove F and O groups from the surface of multilayered MXene powder. Unlike H₂ annealing that removes F effectively but has difficulty in removing O, annealing with Ca effectively removed both O and F. X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy revealed that the proposed approach effectively removed F and O from the MXene powder. The results of O/N analyses showed that the O concentration decreased by 57.5% (from 2.66 to 1.13 wt%). In addition, XPS fitting showed that the volume fraction of metal oxides (TiO₂ and Al₂O₃) decreased, while surface termination groups (-O and -OH) were enhanced, which could increase the hydrophilic and adsorption properties of the MXene. These findings suggest that when F and O are removed from the MXene powder, the interlayer spacing of its lattice structure increases. The proposed treatment also resulted in an increase in the specific surface area (from 5.17 to 10.98 m²/g), with an increase in oxidation resistance temperature in air from ~436 to ~667 ℃. The benefits of this novel technology were verified by demonstrating the significantly improved cyclic charge-discharge characteristics of a lithium-ion battery with a Ca-treated MXene electrode.

• 한국안전학회지
• /
• 제14권1호
• /
• pp.216-221
• /
• 1999

전력용 케이블은 전선로의 지중화 추세에 따라 사용이 증가하고 있다. 케이블 절연체의 경우 장기간의 전압인가에 의해 열화 및 절연파괴 된다. 전력용 케이블의 절연파괴시 발생하는 사회/경제적 문제는 매우 심각한 것으로 알려져 있다. 절연체의 열화에 영향을 주는 요인은 매우 복잡하지만 그중에서도 전기트리 열화에 의한 파괴는 비교적 두꺼운 고체 유전체인 경우에 절연파괴 사고의 주된 원인이 되고 있다. 전기트리의 개시나 진전시 부분방전이 발생하므로 부분방전의 검출에 의해 전기트리의 발생 및 진전 양상을 관측할 수 있고 부분방전의 해석에 의해 절연재료의 잔여 수명을 예측할 수 있다. 본 논문에서는 고전압 전력용 케이블 절연재로써 광범위하게 사용되고 있는 저밀도 폴리에틸렌 시편에서의 전기트리 진전 양상을 비파괴 진단 기법에 의하여 검출하고자 내부 부분방전을 관측/해석하였다.

• Composites Research
• /
• 제36권6호
• /
• pp.422-428
• /
• 2023

스택 체결압에 의해 접촉되는 분리판(BP)과 탄소펠트전극(CFE) 사이의 전기적 접촉저항은 상대적으로 낮은 바나듐 레독스 흐름전지(VRFB) 스택의 체결압 때문에 스택 효율에 큰 여향을 미친다. 본 연구에서는 이러한 접촉저항을 줄이고 셀 성능을 향상시키기 위해 국부 가열 접합 공정을 통해 폴리에틸렌(PE) 복합재료-CFE 하이브리드 BP 구조를 개발하였다. 탄소섬유 복합재료 BP의 PE 매트릭스를 국부적으로 녹여 CFE의 탄소 섬유와 BP의 탄소 섬유의 직접 접촉 구조를 만들어 전기 접촉 저항을 감소시겼다. PE 복합재료-CFE 하이브리드 BP의 성능을 평가하기 위해 면적비저항(ASR)과 기체투과도를 측정하였다. 또한 스택 신뢰성을 측정하기 위해 내산성 시험을 수행하였다. 최종적으로, 개발된 PE 복합재료-CFE 하이브리드 BP와 기존의 BP의 성능을 비교 분석하기 위하여 VFRB 단위셀 충/방전 시험을 수행하였다.

• Journal of Ceramic Processing Research
• /
• 제22권2호
• /
• pp.192-199
• /
• 2021

Peony flower-like γ-Ga₂O₃ nanosheets (γ-Ga₂O₃ NSs) were synthesized and carbon layers were coated on their surfaces using a simple hydrothermal process with subsequent carbonization. The γ-Ga₂O₃ NSs comprised ultrathin layers, which are tens of nanometers in thickness. The carbon-coated γ-Ga₂O₃ NS (γ-Ga₂O₃@C NS) electrode exhibited a specific capacity of 598 mAh g^-1 at 200 cycles, at a current density of 0.5 A g^-1, higher than that of γ-Ga₂O₃ NSs (60 mAh g^-1). Furthermore, a specific capacity of 100 mAh g^-1 at 5 A g^-1 was achieved owing to the low charge transfer resistance through the carbon layers. This study suggests that two-dimensional γ-Ga₂O₃@C NSs with both large specific area and high charge carrier transport are promising active materials for lithium-ion battery anodes with better electrochemical performance.

• 한국진공학회지
• /
• 제19권1호
• /
• pp.36-44
• /
• 2010

관경이 수 mm인 세관 램프 내부에서 플라즈마의 확산을 조사하기 위하여 이극성(ambipolar) 확산방정식을 해하였다. 반경 방향의 확산에 의한 유리관 벽에서의 플라즈마 소멸 특성시간은 $\tau_r\;=\;(r_0/2.4)^2/D_a$로 주어진다. 반경 $r_0{\sim}1\;mm$이고 이극성 확산계수 $D_a{\sim}0.01\;m^2/s$ 이면, $\tau_r{\sim}17\;{\mu}s$이다. 이는 램프의 교류전원 구동에서 플라즈마를 유지하기 위한 구동 최소 주파수 ~30 kHz에 해당한다. 고전압이 인가되는 전극부에 발생한 고밀도의 플라즈마가 양광주로 확산되는 특성시간은 $\tau_z{\sim}0.1\;s$이다. 고밀도 플라즈마 경계에서의 시간에 대한 확산속도는 $t{\sim}10^{-6}\;s$일 때 $u_D{\sim}10^2\;m/s$이고, $t{\sim}10^{-3}\;s$이면 그 속도는 $u_D{\sim}1\;m/s$로 느려진다. 따라서 램프 길이 ~1 m에 대하여 전극부에서 생성된 고밀도 플라즈마가 양광주 전체로 확산되는 시간은 수 초가 걸린다.