• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.8
• /
• pp.1068-1076
• /
• 1997

Emission control of acid exhaust gases from coal-fired power plants and waste incinerators has become an increasing concern of both industries and regulators. Among those gaseous emissions, SO$_{2}$ has been eliminated by a Spray Drying Absorber (SDA) system, where the exhaust gas is mixed with atomized limestone-water slurry droplets and then the chemical reaction of SO$_{2}$ with alkaline components of the liquid feed forms sulfates. Liquid atomization is necessary because it maximizes the reaction efficiency by increasing the total surface area of the alkaline components. An experimental study was performed with a laboratory scale SDA to investigate whether the scrubbing efficiency for SO$_{2}$ reduction increased or not with the application of a DC electric field to the limestone-water slurry. For a selected experimental condition SO$_{2}$ concentrations exited from the reactor were measured with various applied voltages and liquid flow rates. The applied voltage varied from -10 to 10 kV by 1 kV, and the volume flow rate of slurry was set to 15, 25, 35 ml/min which were within the range of emission mode. Consequently, the SO$_{2}$ scrubbing efficiency increased with increasing the applied voltage but was independent of the polarity of the applied voltage. For the electrical and flow conditions considered a theoretical study of estimating average size and charge of the atomized droplets was carried out based on the measured current-voltage characteristics. The droplet charge to mass ratio increased and the droplet diameter decreased as the strength of the applied voltage increased.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.5
• /
• pp.687-690
• /
• 1999

Bacillus stearothermophilus No. 236 isolated from the soil is a strong xylan degrader producing all the xylanolytic enzymes. However, the strain was discovered to be highly intractable to its transformation. In the present study, we have developed a reliable method for transformation of B. stearothermophilus No. 236 by a systematic examination of several factors which might have an influence on the efficiency of electrotransformation. Notably, we found that the most critical factor influencing the transformation efficiency (TE) was the incubation temperature after pulsing, with its optimum incubation of $37^{\circ}C.\; At\; 50^{\circ}C$, the optimum growth temperature of the B. stearothermophilus strain, the transformants could not be obtained at a recognizable level. The combination of field strength of 7.5 kV/cm along with pulse duration of 10 msec (resistance of $400{\Omega}\; and\; capacitance\; of\; 25{\mu}F$) was shown to be the best electrical parameters at the incubation temperature of $37^{\circ}$. A higher TE was obtained when the cells were harvested at an early-exponential phase. Twenty percent of PEG-8000 in a suspension buffer and an addition of 0.1% glycine in the growth medium resulted in about 4-fold and 3-fold increases in TE, respectively. We also found that the plasmid DNA which had been cycled through the host B. stearothermophilus cells enhanced TE by one order of magnitude higher. Under the presently described conditions, $2.5{\times}10^{5} transformants per ${\mu}g$ DNA was attained.

• Journal of Acupuncture Research
• /
• v.34 no.2
• /
• pp.49-59
• /
• 2017

Objectives : This study evaluated the efficacy of electroacupuncture therapy using an insulated needle in adults with abdominal obesity. Methods : This study was a randomized, double-blind, parallel-designed pilot trial. Sixteen participants eligible according to the inclusion and exclusion criteria were randomly divided into an insulated needle group and a control group. Insulated or common needles were inserted at acupoints located on the abdomen (CV12, CV6, ST25, ST27, SP15) and were electrically stimulated for 30 minutes (16 Hz, within tolerable strength). A total of 10 sessions of treatment were performed twice per week for 5 weeks. All participants were requested to maintain their usual diet and lifestyle. The outcome measures were waist circumference (WC), waist-to-hip ratio (WHR), and abdominal computed tomography (CT) of the total fat area (TFA), subcutaneous fat area (SFA), and visceral fat area (VFA). Results : A total of 12 participants divided into the insulated needle group (n = 5) and the control group (n = 7; common needle) were treated for 10 sessions and analyzed per-protocol (PP). WC decreased significantly after 10 sessions in both groups. The WC, TFA, SFA, and VFA of abdominal CT in the insulated needle group decreased more than in the control group; however, there were no significant differences in any parameter between the insulated needle group and the control group. Patients in the insulated needle group were more strongly stimulated with electrical stimulation than patients in the control group. Conclusion : Electroacupuncture using insulated needles in adults with abdominal obesity might be a more effective treatment than common needles. Additional studies are required to compensate for the limitations of this pilot study and to verify the results and efficacy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.458.2-458.2
• /
• 2014

We have demonstrated that simple brush-painted Ti-doped $In_2O_3$(TIO) films can be used as a cost effective transparent anodes for organic solar cells (OSCs). We examined the RTA effects on the electrical, optical, and structural properties of the brush painted TIO electrodes. By the direct brushing of TIO nanoparticle ink and rapid thermal annealing (RTA), we can simply obtain TIO electrodes with a low sheet resistance of 28.25 Ohm/square and a high optical transmittance of 85.48% under atmospheric ambient conditions. Furthermore, improvements in the connectivity of the TIO nano-particles in the top region during the RTA process play an important role in reducing the resistivity of the brush-painted TIO anode. In particular, the brush painted TIO films showed a much higher mobility ($33.4cm^2/V-s$) than that of previously reported solution-process transparent oxide films ($1{\sim}5cm^2/V-s$) due to the effects of the Ti dopant with higher Lewis acid strength (3.06) and the reduced contact resistance of TIO nanoparticles. The OSCs fabricated on the brush-painted TIO films exhibited cell-performance with an open circuit voltage (Voc) of 0.61 V, shot circuit current (Jsc) of $7.90mA/cm^2$, fill factor (FF) of 61%, and power conversion efficiency (PCE) of 2.94%. This indicates that brush-painted TIO film is a promising cost-effective transparent electrode for printing-based OSCs with its simple process and high performance.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.250-256
• /
• 2014

Polypropylene (PP) composites containing conductive multi-walled carbon nanotube (MWNT) and stainless steel short fiber (SSF) were manufactured using a twin screw extruder and characterized their surface resistivity and mechanical properties in this work. Surface resistivity measurements showed that the percolation threshold appeared at a lower MWNT loading when a small amount of SSF was added to PP/MWNT composites. Tensile modulus and strength of the composites increased but elongation-at-break decreased greatly compared to pure PP. Also, the effects of MWNT and SSF on storage modulus and tan ${\delta}$ from dynamic mechanical analysis for the composites were examined, and the morphologies of fractured surface and the fillers were observed using a scanning electron microscope.

• Journal of Biomedical Engineering Research
• /
• v.41 no.5
• /
• pp.210-218
• /
• 2020

Vessel sealing is a medical device that converts electrical or ultrasonic energy into thermal energy and leads to seal, coagulate, and cut the vessel by protein modification within the walls or surrounding connective tissues. As most of surgeries have recently been conducted with minimally invasive surgery, the demand and market for vessel sealing are expected to get bigger. However, there is a problem that electrosurgical or ultrasonic surgical is applied and we have a high risk to evaluate the strength of seal, because the collateral and particular standards currently in force follows have not been establish. Therefore, in this study, we investigated some papers studied on the efficacy and safety of the device, the guidance of FDA and test papers previously conducted from 3 individual subject device made in Korea. We found there is a relationship between burst pressure and the performance of the device, therefore, we propose the vascular bursting pressure test for evaluating the safety and performance of the vessel sealing.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.3
• /
• pp.13-20
• /
• 1991

The present work was aimed to examine the variation of precipitations and mechanical properties by thermomechanical treatments (TMT) in Al-2.19 wt%Li and Al-2.0 wt%Li-0.11 wt%Zr alloys. This study was performed by TEM, SEM observation, DSC, electrical resistance measurement, hardness and tensile strength measurement. First peak of resistivity aged at $90^{\circ}C$ was caused by precipitation of ${\delta}^{\prime}$-precursor phase, and second peak was caused by precipitation of ${\delta}^{\prime}$ phase. According to this result, the precipitation process of Al-2.19 wt%Li alloy was as follow : $SSSS{\rightarrow}{\delta}^{\prime}$-precursor phase ${\rightarrow}{\delta}^{\prime}$ (Coherent ${\rightarrow}$ Semi-coherent) ${\rightarrow}{\delta}$. In a Al-2.0 wt%Li-0.11 wt%Zr ternary alloy, the first peak of resistivity was appeared at initial aging heat-treatment. It is result from exsistant of ${\delta}^{\prime}$-precursor phase. The effect acceleration in a binary alloy was not appeared and the over-aging ternary alloy was accelerated with increase of the reduction rate. It is caused by combination effect of ${\delta}^{\prime}$ and composite phase.

• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.120-125
• /
• 2018

Boron nitride nanotubes (BNNTs) are receiving great attention because of their unusual material properties, such as high thermal conductivity, mechanical strength, and electrical resistance. However, high-throughput and high-efficiency synthesis of BNNTs has been hindered due to the high boiling point of boron (${\sim}4000^{\circ}C$) and weak interaction between boron and nitrogen. Although, hydrogen-catalyzed plasma synthesis has shown potential for scalable synthesis of BNNTs, the direct use of $H_2$ gas as a precursor material is not strongly recommended, as it is extremely flammable. In the present study, BNNTs have been synthesized using radio-frequency inductively coupled thermal plasma (RF-ITP) catalyzed by solid-state ammonium chloride ($NH_4Cl$), a safe catalyst materials for BNNT synthesis. Similar to BNNTs synthesized from h-BN (hexagonal boron nitride) + $H_2$, successful fabrication of BNNTs synthesized from $h-BN+NH_4Cl$ is confirmed by their sheet-like properties, FE-SEM images, and XRD analysis. In addition, improved dispersion properties in aqueous solution are found in BNNTs synthesized from $h-BN+NH_4Cl$.

• Textile Coloration and Finishing
• /
• v.29 no.3
• /
• pp.105-114
• /
• 2017

High tenacity polyethylene(HTPE) fiber is one of the most important synthetic fibers which possesses outstanding properties such as low density, excellent surface hardness and scratch resistance, superior electrical insulation and low cost. In this study, we dyed high tenacity polyethylene filaments using three different solvent dyes based on log P calculations. We evaluated the dyeing characteristics of dyed high tenacity polyethylene filaments based on dyeing temperature, dyeing time and concentration of solvent dyes. We also analyzed the tensile strength and elongation properties of dyed high tenacity polyethylene filaments with various dyeing temperature and dyeing times. The optimized dyeing condition can be found at $120^{\circ}C$ for dyeing time of 1 hour with 4%(o.w.f.) of solvent dyes.

• Korean Journal of Materials Research
• /
• v.30 no.9
• /
• pp.489-494
• /
• 2020

SiC is a material with excellent strength, heat resistance, and corrosion resistance. It is generally used as a material for SiC invertors, semiconductor susceptors, edge rings, MOCVD susceptors, and mechanical bearings. Recently, SiC single crystals for LED are expected to be a new market application. In addition, SiC is also used as a heating element applied directly to electrical energy. Research in this study has focused on the manufacture of heating elements that can raise the temperature in a short time by irradiating SiC-I₂ with microwaves with polarization difference, instead of applying electric energy directly to increase the convenience and efficiency. In this experiment, Polydimethylsilane (PDMS) with 1,2 wt% of iodine is synthesized under high temperature and pressure using an autoclave. The synthesized Polycarbosilane (PCS) is heat treated in an argon gas atmosphere after curing process. The experimental results obtain resonance peaks using FT-IR and UV-Visible, and the crystal structure is measured by XRD. Also, the heat-generating characteristics are determined in the frequency band of 2.45 GHz after heat treatment in an air atmosphere furnace.