• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.312-315
• /
• 2002

This paper summarizes the results of a numerical study conducted to analyze the effect of selected process parameters on material flow and thread profile in thread rolling of large diameter blanks. Based on the previous work where a plane strain mode was found to provide a reasonable approximation of the thread rolling process, the effect of varying thread form, friction factor, flow stress, and blank diameter on effective strain and thread height was analyzed using the finite element code DEFORM. This study show that effective strain for flank angle, that blank diameter had important effect on the as-rolled thread while flow stress, friction factor, and crest round of dies had significant impact on effective strain at the thread root and crest and load of thread rolling. While the rate of strain harding was found to have an effect on the crest profile, the results indicate that it is the primary factor responsible for seam formation in rolled threads.

• 한국정밀공학회지
• /
• 제14권7호
• /
• pp.82-90
• /
• 1997

When a structure is made by the process of forging, it has the different mechanical properties from those it has before the process. This study is based on the crack closure phenomenon of the crack growth behavior of forged AI7050-T7452. The specimens were prepared in three kinds of forging ratio in order to find out the effects of crack closure on the forged material and compare the crack growth behavior with not-forged aluminum. COD method and strain gage method were used in measuring the crack closure stress and the results from those methods were compared each other. FEM analysis was applied to verify the effective stress intensity factor range by the superposition of the crack closure load to the crack tip. In the result of this study, the crack closure stress decreased with increasing the forging ratio due to the finer grain size and the brittle manner.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.243-252
• /
• 1987

본 논문에서는 작은 인공결함을 가진 표면균열의 진전거동을 밝히기 위하여 용접성이 좋고 강도도 적당하며 내식성이 좋아 해양구호무재 및 용접구호물재로서 널 리 사용되는 5083-H113 알루미늄합금을 준비하고 이재료의 피로표면균열 진전거동에 미치는 응력비의 영향을 균열닫힘과 함께 검토하였다.

• Animal Bioscience
• /
• 제34권6호
• /
• pp.1006-1013
• /
• 2021

Objective: Cells have increased susceptibility to activation of apoptosis when suffering heat stress (HS). An effective supplementation strategy to mimic heat-induced apoptosis of bovine mammary epithelial cells (MECs) is necessary to maintain optimal milk production. This study aimed to investigate possible protective effects of the anti-apoptotic activity of 5-aminolevulinic acid (5-ALA) against HS-induced damage of bovine MECs. Methods: Bovine MECs were pretreated with or without 5-ALA at concentrations of 10, 100, and 500 µM for 24 h followed by HS (42.5℃ for 24 h and 48 h). Cell viability was measured with 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assays. Real-time quantitative polymerase chain reaction and Western blotting were used to explore the regulation of genes associated with apoptosis, oxidative stress, and endoplasmic reticulum (ER) stress genes. Results: We found that 5-ALA induces cytoprotection via inhibition of apoptosis markers after HS-induced damage. Pretreatment of bovine MECs with 5-ALA resulted in dramatic upregulation of mRNA for nuclear factor erythroid-derived 2-like factor 2, heme oxygenase-1, and NAD(P)H quinone oxidoreductase 1, all of which are antioxidant stress genes. Moreover, 5-ALA pretreatment significantly suppressed HS-induced ER stress-associated markers, glucose-regulated protein 78, and C/EBP homologous protein expression levels. Conclusion: 5-ALA can ameliorate the ER stress in heat stressed bovine MEC via enhancing the expression of antioxidant gene.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.155-162
• /
• 1995

Redistribution of residual stress and its effects during fatigue crack propagates from tensile residual stress region in weldment are investigated. Tests are performed by using welded CCT specimens of structual rolling steel (SS400) and it makes fatigue crack propagate from tensile residual stress region. For this study tension-tension loading type is selected by external loading condition and magnetizing stress indicator is used correctly to measure redistribution of residual stress according to fatigue crack growth and number of loading cycles. From this result, it is proved that redistribution of residual stress is mainly consist of residual stress released by fatigue crack growth. When fatigue crack propagates from tensile residual stress region residual stress are redistributed and it makes fatigue crack growth rate largely increase. Fatigue crack growth rate is low in case of redistributed residual stress compare with initial distributed residual stress.

• 임상간호연구
• /
• 제22권1호
• /
• pp.38-45
• /
• 2016

Purpose: The purpose of this study was to understand the effects of verbal violence experience, social support, and coping patterns on job stress among operating room(OR) nurses. Methods: The participants were 214 operating room nurses in general hospitals. Data were collected from April 1st to May 1st in 2013 and were analyzed using a multiple regression. Results: The most influencing factor on job stress for OR nurses was verbal violence experience from doctor(${\beta}=.35$), and verbal violence experience from nurse (${\beta}=.27$) followed. Social support from co-workers was a significant factor in decreasing job stress (${\beta}=-.22$). Those three factors explained 43.0% (F=54.76, p<.001) of OR nurses' job stress. Conclusion: The findings of this study revealed that doctors' and nurses' verbal violence increased job stress of OR nurses and social support from co-workers was found decreasing OR nurses' job stress. The results of the study provides an necessity for developing an effective program for minimizing job stress of OR nurses caused by work place verbal violence.

• 한국안전학회지
• /
• 제22권3호
• /
• pp.1-6
• /
• 2007

In order to evaluate fatigue endurance for the rocker arm of a diesel engine, stress measurements were performed using the strain gages attached near the neck, where is one of the most critical region in the rocker arm, in variation of the engine speed. The fatigue life experiments were carried out on miniature specimens from the rocker arms. For evaluating the fatigue endurance of the rocker arm, the S-N data were compared with the stress analysis results through FEM analysis of the rocker arm. The effective stress of the neck region was determined 17.7MPa through FEM analysis of the rocker arm. Conclusively, on the basis of fatigue limit, the rocker arm has a safety factor of 2.8 or 3.4 from the stress measurement or FEM results, respectively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.208-213
• /
• 2004

Methods for estimation of the effective stress intensity factor range (${\Delta}K_{eff}$) are evaluated for narrow and wide band random loading crack growth test data of 2024-T351 aluminum alloy. Three methods of determining $K_{op}$, visual measurement, ASTM offset compliance method, and the neural network method proposed by Kang and Song, and three methods of estimating ${\Delta}K_{eff}$, conventional, the 2/PI0 and 2/PI methods proposed by Donald and Paris, are compared in a quantitative manner by using the results of fatigue crack growth life prediction under random loading. For all $K_{op}$ determination methods discussed, the 2/PI0 and 2/PI methods of estimating ${\Delta}K_{eff}$ provide better results than conventional method for narrow and wide band random loading data.

• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.125-134
• /
• 1989

본 연구에서는, 이러한 상황을 감안하여 피로시험을 위한 유사랜덤 (pseudorandom)하중 파형을 퍼스널컴퓨터 시뮬레이션에 의해 작성하는 소프트웨어를 개발함과 동시에 이를 이용하여 표면피로균열진전시험도 약간 수행하여, 변동하중하의 표면균열 진전거동에 관하여 대체적인 특성을 검토하여 보기로 하였다.

• Tribology and Lubricants
• /
• 제32권1호
• /
• pp.18-23
• /
• 2016

The effective case depth for case-hardened rolling bearing has been discussed. For this purpose, rolling contact fatigue tests for ball bearings built with inner race of various hardness values were conducted until L₁₀ calculating rating life using a bearing life test machine under radial loading. Then, the distribution of residual stress below the inner raceway, which depended on the hardness value, was measured by X-ray diffraction. As a result, the linear relationship was established between the hardness value of the inner race and the theoretical shear stress evaluated at the depth where the residual stress disappeared below the inner raceway. Based on the relationship, it could be found that the factor of safety in bearing manufacturer’s rules for the effective case depth of case hardened rolling bearings was set higher. However, it could be also found that the hardness values at the depth where the maximum shearing stress acted below the raceway surface in a tapered roller bearing hardened by the carburizing process, were not sufficient for preventing plastic deformation under the basic dynamic load rating. Consequently, further efforts were still required to reduce or to disperse the contact load on the material design of a rolling bearing in order to prolong its life.