• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.6
• /
• pp.1-7
• /
• 2002

The use of an asymmetric Mach-Zehnder interferometric amplitude modulator to measure a relatively low frequency electric field strength is described. The sensitivity of an electric field sensor using a Ti:LiNbO$_3$ optical modulator is strongly affected by the shape of a electrode(probe antenna). To measure the low frequency electric field, a probe antenna of wide effective area is more useful than the usual dipole antenna. As a proof of this, the optical modulator was fabricated with a plate-type probe antenna and the usefulness of this antenna tested for measuring low frequency electric field strength. Measurements were performed in the range 0.1V/cm to 60V/cm at 60Hz through 100KHz. Using a probe antenna of 10mm$\times$10mm, the output voltage of 10㎷ was measured with respect to the electric field strength of 0.1V/cm at 60Hz. By increasing the effective area of the probe antenna, better sensitivity is obtainable over the measured range.

• Journal of Practical Engineering Education
• /
• v.9 no.1
• /
• pp.31-39
• /
• 2017

Due to quantitative growth focused on short-term field placement and excessive competition between universities, the need for long-term field placement model is increasing and participation of government and universities is increasing for effective on-the-job training. In order to solve the problems of shortage of R&D manpower in small and medium sized companies, Kumoh Institute of Technology and three participating universities have been conducting industrial internship as R&D long-term field placement program from 2015. Students undertake long-term on-the-job training in the R & D department for six months to improve their R & D skills and strengthen their work capacity. In this paper, we propose effective ways of stimulating cooperative employment through long-term field placement in R&D departments from pre-preparation stage to ending stage through comparative analysis of cases of industrial internship in 2015 and 2016.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.1
• /
• pp.9-15
• /
• 2020

The 'field-effect' underlies the operation of most conventional electronic devices. However, effective control and implementation of the field-effect in semiconductor devices are limited due to screening of the electric-field by conducting electrodes. Thus far, the electronic devices have necessarily been designed to avoid or minimize the electric-field screening effect. As an alternative approach to this, a new type of conducting electrodes which would be transparent to both visible light and electric-field while being electrically conductive have been developed. Here, we define these electrodes as 'electric-field transparent electrodes' and provide a review on related work. Particular attention is paid to the material selection and design strategies to enhance the electric-field transparency of the electrodes while maintaining good electrical conductivity and optical transparency. We then introduce potential applications of the electric-field transparent electrodes in electronic and optoelectronic devices.

• Journal of radiological science and technology
• /
• v.8 no.2
• /
• pp.71-72
• /
• 1985

This study was performed on the dose distribution of various field size and the effect of penumbra shield in the telecobalt unit. The results obtained are as follows. 1. Errors of the light and ${\gamma}-ray$ field size was below the regulation as 0.52 percentage. 2. The coefficient of field area was increased with the larger field area, and this coefficient was showed the more difference in larger SSD. 3. The rectangular field areas, which were described by level of the same percentage depth does, were decreased with the more elongation factor. At the same elongation factor, the compensating factor was decreased with the larger field size. 4. The lead block or extension collimator was able to shield r-ray exposure of outside field size from 50 to 80 percentage. 5. On the matching adjacent fields, while the gap between beam edges are contacted, that overlapped beam edges indicated up to 140 percentage, and while the gap was 1 cm, it could be reduced to 90 Percentage. The lead-libocking on the overlapped area was more effective to lower dose, as 80 percentage in this case. 6. Percentage depth dose of various trimming field sizes were increased linearlly according to area 1 perimeter size, but the center split field size did not maintain linearlly.

• Weed & Turfgrass Science
• /
• v.2 no.4
• /
• pp.358-361
• /
• 2013

This study was conducted to determine the weed control effect of false seedbed in organic rice paddy field. False seedbed is one of the preventative weed control method, especially effective in upland vegetable field. False seedbed frequency and methods were examined by varying the processing time in greenhouse and field condition in 2012 and 2013. In greenhouse experiment, shallow recultivation and harrow surface soil was effective to control weed up to 70%. Optimal processing time of false seedbed was when the weed was two or three leaf stages. Under field condition, one-time treatment of false seedbed was 61% of weed suppression rate and two-times of false seedbed treatment was 79% of weed suppression rate. Monochoria vaginalis was still troublesome weed after false seedbed treatment, but the occurrence of Echinochloa oryzoides was decreased after false seedbed treament. Results indicated that false seedbed treatment was very effective to lower early weed occurrence in rice paddy field especially Echinochloa spp. Weed control efficiency of shallow recultivation by weeder hollow and rotary tillage by tractor were 68%, 13% respectively.

• Radiation Oncology Journal
• /
• v.7 no.2
• /
• pp.279-285
• /
• 1989

Central axis depth dose data for 6 MV X-rays, including tissue maximum ratios, were measured for wedge fields according to Tatcher's equation. In wedge fields, the differences in magnitude which increased with depth, field size, and wedge thickness increased when compared with the corresponding open field data. However, phantom scatter correction factors for wedge fields differed less than $1\%$ from the corresponding open field factors. The differences in central axis percent depth dose between two types of fields indicated beam hardening by the wedge filter The deviation of percent depth doses and scatter correction factors between the effective wedge field and the nominal wedge field at same angle was negligible. The differences were less than $3.20\%$ between the nominal or effective wedge fields and the open fields for percent depth doses to the depth 7cm in $6cm{\times}6cm$ field. For larger $(10cm{\times}10cm)$ field size, however, the deviation of percnet depth doses between the nominal or effective wedge fields and the open fields were greater-dosimetric errors were $3.56\%$ at depth 7cm and nearly $5.30\%$ at 12cm. We suggest that the percent depth doses of individual wedge and wedge transmission factors should be considered for the dose calculation or monitor setting in the treatment of deep seated tumor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.5
• /
• pp.599-606
• /
• 2022

Strain gauges and the bridge weigh-in-motion (BWIM) method are the representative field measurement methods used for fatigue evaluationsof a steel bridge-in-service. For a fatigue reliability evaluation to assess fatigue damage accumulation, the effective stress range and the number of stress cycles applied as the fatigue details can be estimated based on the AASHTO Manual for Bridge Evaluations with the field measurement data of the target bridge. However, the procedure for estimating the effective stress range and the stress cycles from field measurement data has not been explicitly presented. Furthermore, studies that quantitatively compare differences in fatigue evaluation results according to the field measurement data type or processing method used are still insufficient. Here, a fatigue reliability evaluation is conducted using strain and BWIM data that are measured simultaneously. A frame model and a shell-solid model were generated to examine the effect of the accuracy of the structural analysis model when using BWIM data. Also, two methods of handling BWIM data when estimating the effective stress range and average daily cycles are defined. As a result, differences in evaluation results according to the type of field measurement data used, the accuracy of the structural analysis model, and the data handling method could be quantitatively confirmed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.148-160
• /
• 2012

This study proposed more reasonable prediction models on compressive strength and carbonation of concrete structure and developed a more effective tunnel safety diagnosis and maintenance method through field application of the proposed prediction models. For this study, the Seoul Metro's Line 1 through Line 4 were selected as target structures because they were built more than 30 years ago and have accumulated numerous diagnosis and maintenance data for about 15 years. As a result of the analysis of compressive strength and carbonation, we were able to draw prediction models with accuracy of more than 80% and confirmed the prediction model's reliability by comparing it with the existing models. We've also confirmed field suitability of the prediction models by applying field, the average error of an estimate on compressive strength and carbonation depth was about 20%, which showed an accuracy of more than 80%. We developed a more effective maintenance method using durability prediction Map before field inspection. With the durability prediction Map, diagnostic engineers and structure managers can easily detect the vulnerable points, which might have failed to reach the standard of designed strength or have a high probability of corrosion due to carbonation, therefore, it is expected to make it possible for them to diagnose and maintain tunnels more effectively and efficiently.

• Journal of Radiation Protection and Research
• /
• v.33 no.4
• /
• pp.151-160
• /
• 2008

In Korean nuclear power plants (NPPs), two thermoluminescent dosimeters (TLD) were provided to workers who work in an inhomogeneous radiation field; one on the chest and the other on the head. In this way, the effective dose for radiation workers at NPPs was determined by the high deep dose between two radiation dose from these TLDs. This represented a conservative method of evaluating the degree of exposure to radiation. In this study, to prevent the overestimation of the effective dose, field application experiments were implemented using two-dosimeter algorithms developed by several international institutes for the selection of an optimal algorithm. The algorithms used by the Canadian Ontario Power Generation (OPG) and American ANSI HPS N13.41, NCRP (55/50), NCRP (70/30), EPRI (NRC), Lakslumanan, and Kim (Texas A&M University) were extensively analyzed as two-dosimeter algorithms. In particular, three additional TLDs were provided to radiation workers who wore them on the head, chest, and back during maintenance periods, and the measured value were analyzed. The results found no significant differences among the calculated effective doses, apart from Lakshmanan's algorithm. Thus, this paper recommends the NCRP(55/50) algorithm as an optimal two-dosimeter algorithm in consideration of the solid technical background of NCRP and the convenience of radiation works. In addition, it was determined that a two-dosimeter is provided to a single task which is expected to produce a dose rate of more than 1 mSv/hr, a difference of dose rates depending on specific parts of the body of more than 30%, and an exposure dose of more than 2 mSv.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.406-412
• /
• 2009

In this work, a new method to obtain the effective ground conductivity value in the middle frequency band where the informations of soil characteristics are insufficient was proposed. The proposed method obtained the effective ground conductivity values with the measured field strength from sea reference stations and general attenuation model in the middle frequency band. In addition, the proposed method used statistical method to minimize the error between the measurements and the predictions. Then, the effective ground conductivity in Korea peninsular was obtained by using the proposed method. Finally, it was verified that the effective ground conductivity using the proposed method is useful to predict electric field strength in the middle frequency band.