• Journal of the Korean Wood Science and Technology
• /
• 제40권5호
• /
• pp.327-334
• /
• 2012

Wood and concrete show significantly different physical properties, and it need to be firstly understood for using wood-concrete composite. This study is performed for compensating this and effective hybridization of wood and concrete. This research in planned for wood-concrete composite after previous research which deals the shear performance with different anchorage length of steel rebar in wood. Yield mode and reference design value (Z) were derived using EYM (European Yield Model). And the yield mode changed before and after anchorage length of 10~15 mm - $I_s$ mode to IV mode. There was not increasing tendency of shear performance with increased anchorage length for over 20 mm of anchorage in concrete. And wood composite shows 65% and 93% on initial stiffness and yield load respectively compared with the wood-concrete composite. Wood-concrete composite showed brittle failure after yield point while wood-to-wood composite showed ductile failure.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.579-584
• /
• 1998

The purpose of this study is to evaluate the flexural strengthening effects of RC beams reinforced with carbon fiber sheets (CFS) in variable of strengthening amount and anchorage length of CFS. This study can be summarized as follows. The CFS shares the tensile stress such as rebar during loading test. Also, as the strengthening amount of CFS is increased, the maximum flexural strength of RC beams reinforced with CFS is increased. Therefore, it is confirmed that the CFS's strengthening method is very effective to improve the flexural strength of RC beams. The maximum flexural strength of RC beams with CFS is determined by bond failure between CFS and concrete surface. So, the evaluation of CFS's strengthening effect can be calculated using the tensile stress of CFS which is peeling. When the anchorage length of CFS. But, in case of same anchorage length of CFS, when the strengthening amount of CFA is increased, the ductility is decreased. Therefore, it is considered that the anchorage of CFS in the end zone is necessary.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권2호
• /
• pp.195-201
• /
• 1998

The purpose of this study is to evaluate the flexural strengthening effects of RC beams reinforced with carbon fiber sheets (CFS) in variable of strengthening amount and anchorage length of CFS. This study can be summarized as follows ; The CFS shares the tensile stress such as rebar during loading test. Also, as the strengthening amount of CFS is increased, the maximum flexural strength of RC beams reinforced with CFS is increased. Therefore, it is confirmed that the CFS's strengthening method is very effective to improve the flexural strength of RC beams. The maximum flexural strength of RC beams with CFS is determined by bond failure between CFS and concrete surface. So, the evaluation of CFS's strengthening effect can be calculated using the tensile stress of CFS which is peeling. When the anchorage length of CFS is increased, the ductility of RC beams is increased because of delaying the peeling of CFS. But, in case of same anchorage length of CFS, when the strengthening amount of CFS is increased, the ductility is decreased. Therefore, it is considered that the anchorage of CFS in the end zone is necessary.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.185-188
• /
• 2008

플랫 플레이트 시스템은 펀칭전단과 같은 구조적 취약점이 있다. 펀칭전단의 저항력은 기둥단면의 증가, 슬래브 유효춤의 증가, 콘크리트 강도의 증가, 휨철근의 증가로 증가시킬 수 있다. 그러나 전단보강체를 설치하는 방법이 경제적, 시공적, 안정적으로 가장 좋은 방법이다. 하지만 슬래브 두께가 250mm보다 작은 슬래브에서는 전단보강체의 충분한 정착길이를 확보할수 없기 때문에 충분한 정착효과를 발휘하기 힘들다. 이전 연구에서 제안된 전단보강체의 경우 상부철근과 하부철근의 사이에 설치되었기 때문에 전단철근의 항복강도에 도달하기 전에 미끄러짐 파괴가 발생하였다. 정착강도의 영향을 주는 요인으로는 유효정착길이, 콘크리트강도, 전단철근의 직경, 정착상세이다. 본 연구에서는 슬래브 두께와 콘크리트 강도를 고려하여 제안된 보강체의 강도산정시 K factor를 제안하였다. 정착길이와 콘크리트강도를 고려함으로써 두께가 얇은 플랫플레이트 슬래브내에서 전단철근에 의한 전단강도를 정확히 산정할수 있을 것으포 판단된다..

• Geomechanics and Engineering
• /
• 제31권6호
• /
• pp.573-582
• /
• 2022

The geometry of the gravity-type anchorage changes depends on various factors such as the installation location, ground type, and relationship with the upper structure. In particular, the anchorage geometry embedded in the ground is an important design factor because it affects the pull-out resistance of the anchorage. This study examined the effect of four parameters, related to anchorage geometry and embedded ground conditions, on the pull-out resistance in the gravity-type anchorage through two-dimensional finite element analysis, and presented a guide for major design variables. The four parameters include the 1) flight length of the stepped anchorage (m), 2) flight height of the stepped anchorage (n), 3) the anchorage heel height (b), and 4) the thickness of the soil (e). It was found that as the values of m increased and the values of n decreased, the pull-out resistance of the gravity-type anchorage increased. This trend is related to the size of the contact surface between the anchorage and the rock, and it was confirmed that the value of n, which has the largest change rate of the contact surface between the anchorage and the rock, has the greatest effect on the pull-out resistance of the anchorage. Additionally, the most effective design was achieved when the ratio of the step to the bottom of the anchorage (m) was greater than 0.7, and m was found to be an important factor in the pull-out resistance behavior of the anchorage.

• 보존과학회지
• /
• 제28권2호
• /
• pp.141-151
• /
• 2012

석조문화재의 훼손된 부재를 재사용하기 위한 보존관리는 1900년대부터 시작되었다고 볼 수 있는데 일제강점기 시대에 무기물인 시멘트를 원료로 사용하면서 부터이다. 1990년대에 접어들면서 건축 재료인 유기질의 에폭시수지가 도입되었고 현재에 이르기까지 석조문화재 전반에 활용되고 있다. 특히 절단된 부재의 구조적 보강에도 충전제를 혼합하여 사용하는 등의 적극적인 보존처리 작업이 진행되었다. 그러나 구조적 보강을 위해 넣은 금속봉의 길이는 보존과학자의 인지적 경험을 바탕으로 설계하였기 때문에 다양한 매입길이와 함께 원부재의 2차적 훼손을 유발할 수 있다. 따라서 본 실험을 통해 원부재의 훼손율을 최소화하면서 최대의 구조적 보강을 하기 위해 유효정착길이를 표준화한 결과 ø8mm 는 60.88mm, ø12mm는 91.32mm, ø16mm는 121.76mm가 적정하였다. 이 외의 구경은 ${\ell}_d=a_tf_y/u{\Sigma}_0$을 이용하여 정착길이를 구한다. 이 때 사용된 금속보강재는 전산형 환봉을 사용하여야 휨, 전단, 압축 등의 재하하중에 대항할 수 있었다.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.67-73
• /
• 2014

Construction equipment such as tower crane should be installed in a field without appropriate anchorage to cause a collapse of crane. The anchorage capacity can be varied with Anchor length, concrete strength, anchor diameter, hooked or non hooked these variables will be made and tested in the study. It is shown what anchorage capacity will be more effective case by case. Hooked and non-hooked rebar anchor concrete weight with dia 22mm rebar are shown with initial displacement at 170~220KN of hooked case and 200~210KN of non-hooked one which are linearly increased, without any ductility behavior with almost brittleness. Three(3) same test pieces are almost similarly behaviored without relation to hooked or non-hooked cases. It is found out that the bigger diameter of rebar becomes, the more resistant capacity could be made, but conversely ductility against sudden collapse similar to brittleness becomes the more insufficient. It is also found out that dia 16mm rebar could be more effectively applied to heavy support weight at construction sites.

• 대한치과교정학회지
• /
• 제45권2호
• /
• pp.95-101
• /
• 2015

The aim of this case report is to describe the treatment of a patient with skeletal Class III malocclusion with maxillary retrognathia using skeletal anchorage devices and intermaxillary elastics. Miniplates were inserted between the mandibular lateral incisor and canine teeth on both sides in a male patient aged 14 years 5 months. Self-drilling mini-implants (1.6 mm diameter, 10 mm length) were installed between the maxillary second premolar and molar teeth, and Class III elastics were used between the miniplates and miniscrews. On treatment completion, an increase in the projection of the maxilla relative to the cranial base (2.7 mm) and significant improvement of the facial profile were observed. Slight maxillary counterclockwise ($1^{\circ}$) and mandibular clockwise ($3.3^{\circ}$) rotations were also observed. Maxillary protraction with skeletal anchorage and intermaxillary elastics was effective in correcting a case of Skeletal Class III malocclusion without dentoalveolar side effects.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.393-398
• /
• 1999

The main objective of this project is to define the ultimate bond performance of domestic prestressing strands in the precast prestensioned concrete beams. Eight specimens from four different companies were fabricated and tested in this study. Four-point loading tests were performed on the beams of domestic strands with an arbitrary anchorage length. The research has shown, that all seven specimens except one failed in bond are capable of developing their full flexural capacity and the strands within them are fully anchored even with the sudden transfer of frame cutting. Following results are summarized from the tests conducted. 1) All of the specimens are tested at an embedment lengths much shorter than those required by the ACI code, failed in flexure except one failed in bond. 2) It seems that the beam depth can not be an effective variable to estimate the bond length within these sections and length of specimens on this tests. 3) The development length with the stirrup space which are considered for correction factors in the equations of Russel and Paulsgrove, is fully accurate to determine the required length for the beam tested in this research.

• 한국지반공학회지:지반
• /
• 제10권4호
• /
• pp.133-152
• /
• 1994

In the present study, an economic design of Anchored Geosynthetic(AG) System applied mainly to reinforce unstable soil slopes is investigated. For this purpose methods of stability analysis are developed to determine the optimum installation angle, required minimum length and maximum spacing of nails. Anchorage of nails within the soil mass is achieved by frictional resistance to pull out along the effective length of the nails. Cases of infinite slope and finite slope are dealt with individually. Silce methods of stability analysis developed in the present study are limit-equilibrium-based. For the case of finite slope Spencer method which considers interslice force is modified to evalyate the overall stability. In addition, the effects of various design parameters on requried length and spacing of nails corresponding to the optimum orientation of nails are analyzed. Based on the analysis, a simplified equation is given for the optimum nail orientation. Also the importance of optimum nail orientation is illustrated throughout design example, and the appropriateness of judgment criterion are examined.