• Food Science and Preservation
• /
• v.22 no.4
• /
• pp.498-504
• /
• 2015

The purpose of the present study is to provide preliminary data for turning sweetpotato leaves into dehydrated vegetables. To achieve this goal, we have gone through the process of hot-air drying the leaves of sweetpotato that are usually thrown away and examined the drying speed and rehydration resilience, then made a comparative analysis of the general ingredients, lutein, $\beta$-carotene and chromaticity. The drying speed reached the peak at a temperature of $70^{\circ}C$. As for other general ingredients, there was no significant difference according to temperature. The content of lutein, which is a functional ingredient, was large in Shinmi with $171.59{\mu}g/g$ at a temperature of $40^{\circ}C$; small in Hayanmi with $73.75{\mu}g/g$ at a temperature of $70^{\circ}C$. The content of $\beta$-carotene was large in Shinmi with $379.59{\mu}g/g$ at a temperature of $40^{\circ}C$; small in Hayanmi with $170.78{\mu}g/g$ at a temperature of $70^{\circ}C$. The content of functional materials was the largest at a temperature of $40^{\circ}C$, and decreased in the order of temperatures at $50^{\circ}C$, $60^{\circ}C$, and $70^{\circ}C$. As for rehydration stability, rehydration rate in both Shinmi and Hayanmi was the highest at a temperature of $40^{\circ}C$ with 233.93% and 223.47% respectively. To summarize, the quality of dried sweet potato leaf was more affected by temperature than by drying time, and low temperature drying resulted in better product value.

• Textile Coloration and Finishing
• /
• v.18 no.3 s.88
• /
• pp.42-48
• /
• 2006

The aim of this work is to develop Thick-Thin polyester yarn(T-T yarn) with finer than 1 denier mono filament. The manufacture of T-T yarns were carried out in a draw-winder using 85d/72f PET filament with various spinning speed of 2700, 2900, and 3100 m/min, respectively. The structure and physical properties of T-T yarns with spinning speed and over feed ratio were examined by draw-winder processing the sample in $100^{\circ}C$ water for 20 min and drying in 120, 140, 160, and $180^{\circ}C$ of dry air for 20 min. The crystallinity, the birefringence and the initial elasticity modulus of T-T yarns increased with increased spinning speed of filament and the heat treatment temperature but at the temperatures higher than $140^{\circ}C$ the increased rates show a tendency to decrease. Moreover, the initial modulus and the tenacity of T-T yarns increased with decreasing the over feed ratio of filament and the those of T-T yarns decreases with increasing the heat treatment temperature. The shrinkage of T-T yarns decreased with decreasing spinning speed and increased over feed ratio of filaments. Consequently, the results indicate that the best T-T yarn under 1 denier was optimized from PET filament with spinning speed of 2700 m/min and over feed ratio of 0.67

• Journal of the Korean Society for Railway
• /
• v.17 no.4
• /
• pp.270-280
• /
• 2014

In this study, to examine the causes of cracks in continuously reinforced concrete tracks (CRCTs) and the main factors affecting cracking, a field survey on the status of cracks and crack patterns in the Gyeong-bu high speed line was conducted, and the crack patterns of CRCT due to the temperature difference between the top of the slab (TCL) and the bottom of the subbase (HSB) and the drying shrinkage of concrete were predicted by a nonlinear finite element model considering the structure of CRCT. The results of the numerical analysis show that cracks will be developed at the interface between the sleeper and the TCL, and under the sleeper due to the temperature difference and concrete shrinkage. This corresponds well to the crack locations found in the field. Also, it is found that the most significant factors are the coefficient of thermal expansion with respect to the temperature difference, and the drying shrinkage strain with respect to shrinkage. According to the results, the reinforcement ratio should be carefully determined considering the structures of CRCT because the crack spacing is not always proportional to the reinforcement ratio due to the sleepers embedded in the TCL.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.381-391
• /
• 1999

A new 5th generation adhesive system(ONE-STEP) has been supplied which operators can apply to conditioned tooth surfaces by one simplified step. The purpose of this study was to determine whether different methods of adhesive application and various air drying duration after applying adhesive affect the shear bond strength of composite resin to dentin, and to evaluate the adhesive pattern of composite resin and dentin under SEM. Seventy-seven extracted human molar teeth were cleaned and mounted in palstic test tubes. The occlusal dentin surfaces were exposed with Diamond Wheel Saw and smoothed with Lapping and Polishing Machine (South Bay Technology Co., U.S.A.). Teeth were randomly divided into 7 groups (n=11), In experimental A group, adhesive was applied to dentin with agitation for 20 sec. In experimental N-A group, adhesive were continuously applied to dentin for 20 sec. Also control and experimental 1, 2, 3, 4 groups were dried for 10, 0, 5, 20, 30 seconds after applying adhesive, respectively, Adhesives were light cured for 10 sec. A gelatin capsule 5mm in diameter was filled with Aelitefil$^{TM}$ composite resin, placed on the treated dentin surface and light cured for 40 see, from three sides, All specimens were stored in distilled water at room temperature for 24 hours. The shear bond strengths were measured using a universal testing machine(AGS-1000 4D, Japan) at a crosshead speed of 5mm/min. An one-way ANOVA and LSD test were used for statistical analysis of the data. For SEM evaluation, seven specimens were made and sectioned. Representive postfracture and seven specimens were mounted on brass stubs, sputter-coated with gold and observed under SEM. The results were as follows : 1. The shear bond strength of experimental A group which adhesive were applied to dentin with agitation was higher than that of experimental N-A group (continuous application), and there was significant difference between two groups (p<0.01). 2. The interface between composite and dentin according to different application methods showed close adaptation in experimental A group and showed tinny gap in experimental N-A group. 3. The shear bond strength accoding to various air drying duration was the lowest value(7.57${\pm}$2.60 MPa) in experimental 1 group, so there was significant difference between experimental 1 group and other four groups (p<0.05). But there was no significant difference of shear bond strength between four groups (p>0.05). 4. The interface between composite and dentin according to various air drying duration showed close adaptation in control group and tinny gap in experimental 3 and 4 groups. But experimental 1 and 2 groups showed $30{\mu}$ and 6 - $10{\mu}m$ thick gaps, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.443-450
• /
• 2019

We studied to find the optimal manufacturing conditions of coffee grounds sludge RDF with oil drying method. We expanded the lab scale to pilot scale to compare the efficiency of the oil-drying equipment and The selection of the ratio of coffee grounds and oil, the setting temperature, and the temperature change and water content with time were measured. In order to analyze the characteristics of the research results, characteristics of solid fuels produced(Coffee grounds of oil-dried) by calorimeter, TGA, combustion equipment, and combustion gas measuring instrument were analyzed. As a result, the ratio of oil to coffee grounds was 4: 1, and when the setting temperature was set to $300^{\circ}C$, the water content reached 10wt.% or less within 20 minutes. ln addition, it showed high calorific value of 6,273kcal/kg. However, coffee grounds had a similar composition to wood and showed high luminance and produced a lot of CO in combustion gas. As a result, it is considered to be unsuitable for thermoelectric power plant and camping fuel, but the initial ignition speed is high and the heat generation is high, so it is considered that it can replace the fuels for current use.

• Korean Journal of Food Science and Technology
• /
• v.51 no.1
• /
• pp.29-34
• /
• 2019

In this study, a commercial production stepwise method for restorative rice with high quality and microbial safety was developed. The stepwise treatment method included steaming, refrigerated aging, and low temperature drying. The soaking rice was steamed twice at $90-100^{\circ}C$, and then, the rice was aged at $0-10^{\circ}C$, frozen at $-20^{\circ}C$, and dried at low temperatures with 5 m/s wind speed at $1-20^{\circ}C$ and 85% relative humidity. Applying the three steps improved sensory qualities compared with the conventional hot air drying and made storage at room temperature for 3 months possible. Specifically, the moisture content of the restorative rice was increased to 30%, which was 4.3 times higher than the 7% of the conventional air dried rice, and the rice grain shape was well maintained. The texture and appearance of the three-step rice were significantly improved (p<0.05) in a sensory evaluation.

• Food Science and Preservation
• /
• v.16 no.4
• /
• pp.541-548
• /
• 2009

We developed a surface washing system for ginseng. The washing system was developed using different treatments and conditions and characterized in terms of product hardness, weight loss, and change in temperature and color. Optimal results were obtained using a surface washing system involving a washing conveyor speed of 1.0 L/min, a water pressure of $35\;kg/cm^2$, a washing nozzle angle of $40^{\circ}$, a washing height of 5 cm, a 1-sec reciprocating washing nozzle cycle, a dehydration wind velocity of 30 m/sec, and an internal drying temperature of $30-33^{\circ}C$. A surface washing system using a washing conveyor speed of0.8 L/min, a water pressure of $40\;kg/cm^2$, a washing nozzle angle of $40^{\circ}$, a washing height of 3 cm, a 1-sec reciprocating washing nozzle cycle, a dehydration wind velocity of 30 m/sec, and an internal drying temperature of $30-33^{\circ}C$ resulted in ginseng that was stained yellow.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.911-919
• /
• 1994

As the study for preparation of single-layer anti-reflective coating on glass, the conditions of synthesis of sol for coating and of reproducible coating procedure were investigated. In case of water-based sol, coating was impossible because of poor wettability of sol. The Substitution of solvent with ethanol improved the wettability of sol on the glass surface, and optimum amount of ethanol for substitution was 70 vol%. Maximum specific surface area and total pore volume of water-based sol were 268.7$m^2$/g and 0.315 cc/g, but after substitution, those values increased to 404.1 $m^2$/g and 0.376 cc/g, respectively. The upper limit withdrawl speed of coating in order to get clean coated films without aggregations or stains was 7 cm/min. In case of addition of 0.1 mol HNO3 and substitution with 70 vol% ethanol and heat-treatment at 40$0^{\circ}C$ for 1 hour, thin film with thickness of 94 nm was obtained at withdrawl speed of 4 cm/min. The thickness of thin film was independent of drying time.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.4
• /
• pp.351-356
• /
• 2017

The resistance of printed patterns for electrodes fabricated using printing technology should be minimized. This parameter depends on the pattern width and thickness; however, from the viewpoint of printability, the printed patterns should be printed at the designed width. The resistance of the printed patterns as well as printability is affected by various printing conditions. In this paper, the printing condition is optimized to minimize the resistance of electrodes printed by the roll-to-roll gravure method. This is done by considering the spread ratio of pattern width as a parameter of printability using design experiments. The drying temperature, dryer fan speed, and printing speed are selected as effective factors for the experiment objective. The optimized conditions are obtained and reproducibility test using these demonstrates that the optimized conditions can produce low-resistance electrodes for printability of the pattern width.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.12
• /
• pp.1724-1728
• /
• 2002

The adsorption of proteins on the surface of glass slides is essential for the construction of protein chips. Here, we report that a Histidine (His)-tagged protein protein has been efficiently adsorbed on glass coated with nickel. A variety of nickel chloride-coated plates were prepared by the spin-coating method and adsorbed to the His-tagged protein. When the protein was adsorbed onto the surface of a variety of nickel chloride-coated glass slides, the efficiency of protein adsorption was dependent upon the coating conditions such as nickel chloride concentration, the spin speed and the drying temperature. The slides appropriate for protein adsorption were obtained when the slides were coated with 11%(w/w) of $NiCl_2$ at the spin speed of 4000 rpm for 20 sec and then dried at higher than 40°C. The physical properties of their nickel chloride thin layer were characterized by scanning electron microscopy. x-ray diffraction and atomic force microscopy, finding that the nickel chloride particles were around 10 nm in diameter and uniformly crystallized at 101 faces. These results show that nickel chloride-coated slides prepared by the spin-coating method are utilizable for the construction of Histagged protein chips.