• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2856-2861
• /
• 2008

A catalytic burner has been developed to utilize thermal energy from the fossil fuel without nitrogen oxides (NOx) emission. The burner is shaped into a mat to maximize the heating surface. Premixed combustion has been developed to be used in a closed chamber, such as a radiation type industrial dryer. The burner yields the thermal energy in the form of thermal radiation in the infrared regime, which is proved to be effective to dry organic substances for low moisture condition. Thermal efficiency including the sensible heat is better correlated to the moisture compared to the dry rate.

• 한국식생활문화학회지
• /
• 제32권2호
• /
• pp.135-143
• /
• 2017

This study evaluated the quality characteristics of semi-dried noodles prepared with different water contents (wet noodles; 32, 24, 22, 20%, dry noodles; 12%). The drying process was carried out in a drying chamber at $13{\sim}18^{\circ}C$ temperature and 75~95% humidity. The proximate composition of Korean wheat flour was as follows: water $22.1{\pm}3.64%$, protein $8.6{\pm}0.13%$, fat $1.3{\pm}0.10%$, ash $0.7{\pm}0.02%$, carbohydrates $67.3{\pm}0.10%$. As water contents decreased, both L and b values significantly decreased before cooking of noodles, whereas L, a, and b values were not significantly different after cooking of noodles. Weight, water absorption, and volume of cooked noodles significantly increased as water content decreased, whereas turbidity of soup was not significantly different. Cutting hardness before cooking of noodles significantly increased as water content decreased. Sections of noodles after cooking by SEM (scanning electron microscopy) showed roughness and fewer round starch particles as water content decreased. For overall preferences according to the sensory evaluation, noodles prepared with different water contents were not significantly different. According to the results, semidried noodles have development potential to complement the disadvantages of both wet noodles and dry noodles.

• 한국농공학회지
• /
• 제16권4호
• /
• pp.3545-3554
• /
• 1974

The objective of this study was to investigate the characteristics of the evaporation rate, the plastic shrinkage and the compressive strength of concrete exposed to a rapid evaporation environment immediately after casting. Drying of concrete were conducted under a controlled chamber in which the temperature was mainfoimed at 30 ${\pm}$1$^{\circ}C$, the relative humidity 22 ${\pm}$1 percent, and the wind velocity 7 ${\pm}$1 m/sec. The compressive strength of concrete was tested after 28 days of standard curing. The results obtained are as follows: 1. The evaporation rate was the highest at the very beginning, was decreased as the drying progresses, and was kept almost constant after 6 hours. 2. The shrinkage of concrete was changed in three different rates for the concrete mixture having its slump vallue between 3.0cm and 7.5cm. 3. The plastic shrinkage was ended within 5 or 6 hours after casting, regardless of the water cement ratio. 4. The shrinkage was increased within the limit of slump values between 3.0cm and 7.5cm as the water-cement ratio was increased. 5. The evaporation was kept on even after the plastic shrinkage was ended. 6. Within the limit of good workability (slump value between 4.5cm and 7.5cm), the compressive strength of concrete was increased when the shrinkage rate was slow but it was decreased when the rate was rapid 7. From the result of this study it is recommended that (1) the water-cement ratio should be less as long as the workability of concrete is allowable; (2) the evaporation should be prevented at least for 4 hours after casting concrete.

• 한국응용과학기술학회지
• /
• 제31권2호
• /
• pp.183-189
• /
• 2014

내화성 및 내화학성이 우수한 현무암사의 표면에 회분식 방법에 의한 테프론 코팅 연구의 결과를 토대로 연속식 코팅 공정 인자를 도출하기 위한 연구를 수행하였다. 현무암사를 7,5 wt% 트리에톡시트리플루오로실란(TMTFPS)으로 연속적으로 전처리 한 후, 침투제로 0.25 wt% bis(2-ethylhexyl)sulfo succinate (DOS-Na)가 함유된 20 wt% 테프론 수분산액으로 딥 코팅한 후 2 m의 $120^{\circ}C$ 건조 챔버에서 12 m/mim의 속도로 건조한 후 2 m의 $380^{\circ}C$ 소성 챔버에서 40초간 소성하여 최종 $3.4g_f/D$의 인장 강도와 $2.3g_f/D$의 루프강도를 가지는 테프론이 코팅된 고내열 재봉사용 현무암사를 제조하였다.

• 보존과학회지
• /
• 제12권1호
• /
• pp.71-82
• /
• 2003

사적 259호 선원사지(禪源寺地) 4차 발굴에서 출토된 지류(紙類) 유물들을 분석을 하고 이를 통해 보존상황에 맞는 보존처리방법을 연구하였다. 지류(紙類) 유물이 펼쳐볼 수 없는 상황에서 가장 중요한 보존처리 과정은 유물의 분리이고, 분리는 지류(紙類) 유물의 상태에 따라 분리방법을 달리하여 연구하였다. 건조한 상태의 유물 중에서 경화정도가 약한 것은 Gore-Tex chamber를 제작하여 분리하고, 경화정도가 강한 것은 여과수를 사용하여 분리하였다. 젖은 상태의 유물은 진공동결건조방법을 통해서 분리하였다. 지류유물의 분석은 재료의 특징을 알기 위한 종이의 조사, 전자현미경과 SEM을 통한 섬유의 분석, X선 형광분석법(XRF)에 의한 글씨 재료를 분석하였다. 유물의 제작 연대를 추정하기 위하여 가속기 질량 분석기에 의한 탄소연대측정을 하였다. 분석과 보존 처리 과정을 통하여 출토 유물의 분류가 되었고, 유물의 분류는 원형을 상실한 유물들의 원형보존을 가능하게 하였다. 본 논문에서는 가장 열악한 상태의 지류유물의 보존처리 방법의 적용을 제시해 보았고, 탄소연대측정을 통하여 자료도 제시할 수 있었다.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.589-598
• /
• 2000

A pilot-scale Spray Drying Sorber (SDS) system was set up to evaluate the effect of spray characteristics on the desulfurization yield. The size distribution and the Sauter Mean Diameters of slurry droplets were measured in advance using the optical size measurement system, Malvern 2600. The desulfurization yield of the drying chamber by size was measured for the conditions of inlet gas and spray injection. As a reagent, 10% limestone slurry of $Ca(OH)_2$ was treated with flue gas containing $SO_2$, and the combustion gas analyzer and gas detectors were attached to measure the $SO_2$ concentration. With a flow rate of 144 Nm3/h and a temperature range of $200{\sim}300^{\circ}C$, the experiments were performed for the Stoichiometric Ratio (SR) of 1.0 to 3.0 and droplet mean diameter of 6.5 to $34.3{\mu}m$. In case of smaller spray droplets, the desulfurization efficiency improved due to the increase of total droplet surface area, while the reduction in evaporation time reduced the contact time between the droplets and $SO_2$ gas. In some typical region of droplet diameter, this negative effect, reduction of contact time, became dominant and the desulfurization yield decreases the desulfurization yield in spite of the expansion in absorption area. These results revealed that there exists the optimal size of spray droplets for a given state, which is determined by the compromise between the total surface area of slurry droplets and the evaporation time of droplets. The measurements also indicated that the inlet temperature of flue gas changes the optimal injection condition by varying the driving force for evaporation. The results confirm that the effect of the evaporation time of slurry droplets should be considered in analyzing the desulfurization yield as well as the total surface area, for it is a significant aspect of the correlation with the capabilities of $SO_2$ absorption in wet droplets. In conclusion, the optimal condition of spray can be determined based on these results, which might be applied to design or scale-up of SDS system.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.476-482
• /
• 2009

This paper describes the development of capacitive sensor for the diagnosis of liquid dielectrics, which is widely used as the electrical insulating oil of transformer, circuit breaker, cable and etc. To survey the dielectric properties of the virgin and aged electrical insulating oils, we utilized the highly precise measuring system, using the principle of cross capacitance. The measured properties were used to determine the design factors of the sensor. Then the factors were optimized with the help of computational analysis. To evaluate diagnosis by the sensor, we performed accelerated thermal aging test about electrical insulating oils. The condition of aged specimens were investigated by measurements of relative permittivity i.e. capacitance change by capacitive sensor. And to evaluate the hysteresis characteristics with the change of temperature, we constructed a testing system, which was composed with vacuum drying oven, oil chamber and measuring instruments, such as LCR meter, MUX and so forth. Through the results of this investigation, we confirmed the superior characteristics of the newly developed sensor.

• 한국연초학회지
• /
• 제21권1호
• /
• pp.5-9
• /
• 1999

In recent years, the line of increase in policy on tobacco production triggered a rise in the loading volume per bulk curing barn, and manufacturers boosted the output of their blowers in order to prevent dirty leaves in the process of curing. for this reason, we studied the effect of the reducing air flow in bulk curing chamber from the color fixing stage to the stem drying stage of flue curing process on physical properties of cured leaves. The control of air flow was composed of the reducing air velocity of blower by means of a voltage regulator (slidac), and condition before color fixing stage was all the same with the conventional curing method. As a result, an effectiveness of improvement in the physical properties of cured leaves were observed. The leaves cured by this method were somewhat orange in color of upper stalk position, better bodied, and less brittle compared with the leaves produced by conventional curing. However, the leaves cured by this method had a little sharpness and harshness. As to the physical properties, there was decreased in occurrence of flat leaves than that of conventional ones. On the other hand, in case of reducing air flow during the curing process, increase of price per kg reached to about 5 % compared with those of conventional curing method.

• 한국지역사회생활과학회지
• /
• 제21권4호
• /
• pp.551-558
• /
• 2010

It is a normal circumstance to have high temperature and high humidity in Greenhouses even though these climates are changed by the area, season, climates, the size of the greenhouse, and the crops being raised. Workers in the greenhouses have complained about their uncomfortable work environment and discomfort from the hot conditions, including sunburn. The farmers' ailments are not significantly different between those working in the in greenhouses and those working in the fields. The Farmers' syndrome was almost two times higher for women than those of men for greenhouse workers. This study was developed for functional fatigue clothes for plastic greenhouses which are known for high temperatures and humidity. The ergonomic function and thermal comforts of fatigue clothes were evaluated in the climatic chamber($30.0^{\circ}C$, 70.0%R.H.). The current fatigue clothes which are made of cotton or nylon were purchased at the market. The developed clothes are made of highly absorbent and high speed drying polyester. And these fabrics have excellent elasticity. In this study, the functional fatigue clothes were designed with longsleeved sport shirts and Full length pants. Tre, Tsk, Hcl, HR and the personal subjective sensations such as heat, humidity, and comfortableness were significantly lower when subjects wore the developed clothes made with polyester than the previous attire.

• Journal of Biosystems Engineering
• /
• 제32권2호
• /
• pp.102-108
• /
• 2007

Heat pump systems are recognized to be heating and cooing systems. In this study, to check the practical application possibility of heat pump systems as low temperature storage systems and get basic data, apples of a long term storage items were stored and performance of low temperature storage and quality changes of apples were evaluated. Cooling coefficient of performance of the system was from 1.1 to 1.3. Although ambient air temperature varied widely from $-13^{\circ}C$ to $29.6^{\circ}C$ during low temperature storage period from January to June, the average temperature of low temperature storage chamber was $1.1^{\circ}C$ at setting temperature of $1.5^{\circ}C$. Sucrose of apples stored by the heat pump decreased from initial sucrose of 15.4% (Brix number) to final sucrose of 14.3%. Weight loss ratio of apples was 9.7% and internal and external view of apples after low temperature storage were very satisfactory with the naked eye.