• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.147-148
• /
• 1998

In this paper, we developed the process for depth-probe type silicon microelectrode arrays. The process consists of four mask steps only. The steps are for defining sites, windows, and for shaping probe using plasma etch from above, and for shaping using wet etch from below, respectively. The probe thickness is controlled by dry etching, not by impurity diffusion. We used gold electrodes with a triple dielectric system consisting of oxide/nitride/oxide. The shank of the probe taper from 200um to tens of urn tip and has 30 um thickness.

• Journal of Korean Vacuum Science & Technology
• /
• v.3 no.1
• /
• pp.24-29
• /
• 1999

The characteristic behaviors of CH3Br were examined first for the dry etching of polysilicon in a Cl2/CH3Br/O2 plasma. CH3Br is revealed one of the excellent additive gases to control anisotropy of etching profile and to give no undercutting for various typed of polysilicons. CH3Br acts as a passivation precursor on the side wall in etch cavity by forming polymer-like films such as CHxBry(x+y=1,2). The decrease of etch selectivity due to the reaction if the C-containing species from CH3Br with the surface O atoms of SiO2 was overcome by the addition of O2 into plasma, resulting that the selectivity increased by 2~3 times. According to the results of optical emission signals, CH3Br should be dissociated into several fragments to give more hydrogen atoms than bromine atoms in our helical resonator system.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.2
• /
• pp.60-69
• /
• 1998

Polysilicon surface mdoification tecnique is developed to reduce the sticking of microstructures fabricated by micromachining. Modified anti-sticking grain holes are simply formed by two-step dry eth without additional photolithography nor deposition of thin films. Both process-induced sticking and in-use sticking are successfully reduced more than two times by adopting grain holed polysilicon substrate. A sticking model for cantilever beam is derived. This model includes bending moment stems from stress gradient along the thickness directionof structural polysilicon. Because the surface tension of rinse liquid and the surface energy of the solids to be stuk tend to decrease in recently developed anti-sticking techniques, the effect of stress gradient will play an important role to analyze the sticking phenomena. Effect of the temperature during post-release rinse and dry is modelled and verified experimentally. Based on developed anti-sticking polysilicon structure and the sticking model, sticking of microstructure, fabricated by simple wet process including sacrificial layer etch and rinse with deionized water without special equimpment for post-release rinse and dry was alleviated more than 3.5 times.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.77-78
• /
• 2000

We verified the charged static electricity on LCD glass influences upon the etching uniformity of dry etching process by plasma. In the TFT-LCD manufacturing process, we mainly paid attention to eliminate the static electricity for TFT reliability. The static electricity caused the serious ununiformity of etching surface profile and etching rate in the dry etch process. Through our experiment on the made static electricity from -200V to -1000V, it was confirmed that the static electricity on LCD glass caused the etching rate variation of $1.5%{\sim}15%$. We recommend the etching process equipment for LCD manufacturing have to establish the soft X-ray exposure module system for eliminating the static electricity inside the loading and unloading chamber.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.421-426
• /
• 2009

We report on the capacitively coupled O2 plasma etching of PMMA and polycarbonate (PC) with a diffusion pump. Plasma process variables were process pressure and CCP power at 5 sccm $O_2$ gas flow rate. Characterization was done in order to analyze etch rate, etch selectivity, surface roughness, and morphology using stylus surface profilometry and scanning electron microscopy. Self bias decreased with increase of process pressure in the range of 25$\sim$180 mTorr. We found an important result for optimum pressure for the highest etch rate of PMMA and PC, which was 60 mTorr. PMMA and PC had etch rates of 0.46 and 0.28 ${\mu}m$/min under pressure conditions, respectively. More specifically, etch rates of the materials increased when the pressure changed from 25 mTorr to 60 mTorr. However, they reduced when the pressure increased further after 60 mTorr. RMS roughnesses of the etched surfaces were in the range of 2.2$\sim$2.9 nm. Etch selectivity of PMMA to a photoresist was $\sim$1.5:1 and that of PC was $\sim$0.9:1. Etch rate constant was about 0.04 ${\mu}m$/minW and 0.02 ${\mu}m$/minW for PMMA and PC, respectively, with the CCP power change at 5 sccm $O_2$ and 40 mTorr process pressure. PC had more erosion on the etched sidewall than PMMA did. The OES data showed that the intensity of the oxygen atomic peak (777.196 nm) proportionally increased with the CCP power.

• Journal of the Korean Vacuum Society
• /
• v.15 no.6
• /
• pp.630-636
• /
• 2006

Scale down of semiconductor gate pattern will make progress centrally line width into transistor according to the high integration and high density of flash memory semiconductor. Recently, the many researchers are in the process of developing research for using the ONO(oxide-nitride-oxide) technology for the gate pattern give body to line breadth of less 100 nm. Therefore, etch rate and etch profile of the line width detail of less 100 nm affect important factor in a semiconductor process. In case of increasing of the platen power up to 50 W at the ICP etcher, etch rate and PR selectivity showed good result when the platen power of ICP etcher has 100 W. Also, in case of changing of HBr gas flux at the platen power of 100 W, etch rate was decreasing and PR selectivity is increasing. We founded terms that have etch rate 320 nm/min, PR selectivity 3.5:1 and etch slope have vertical in the case of giving the platen power 100 W and HBr gas 35 sccm at the ICP etcher. Also notch was not formed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.4
• /
• pp.164-168
• /
• 2011

Etch selectivities of mask materials to ZnO and $SnO_2$ films were studied in $BCl_3$/Ar and $CF_4$/Ar inductively coupled plasmas for fabrication of nanostructure-based gas sensing layer with high aspect ratios. In $25BCl_3$/10Ar ICP discharges, selectivities of 5.1~6.1 were obtained for ZnO over Ni while no practical selectivity was obtained for ZnO over Al. High selectivities of 7 ~ 17 for ZnO over Ni were produced in $25CF_4$/10Ar mixtures. $SnO_2$ showed much higher etch rates than Ni and a maximum selectivity of 67 was observed for $SnO_2$ over Ni.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.3
• /
• pp.1-5
• /
• 2000

Inductively coupled plasma (ICP) excited by a spiral planar antenna is used to etch elctrodes for PZT capacitors. Pt/RuO$_{2}$ bilayers are tested as bottom electrodes for PZT capacitors in order to utilize better leakage characteristics of Pt and easy etch characteristics of RuO$_{2}$ at the same time. The etch rates and selectivities to SiO$_{2}$ hard mask have been measured for each of Pt and RuO$_{2}$ in terms of various plasma conditions. As Cl$_{2}$ ratio increases in $O_{2}$/Cl$_{2}$ mixture, the etch rate of Pt increases while that of RuO$_{2}$ reaches the highest near 10 ％ of Cl$_{2}$. Optimum gas mixture ratio has been determined for etching Pt and RuO$_{2}$ bilayers sequentially, and sub-half micron patterning is demonstrated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.41-43
• /
• 1999

Among the feffoelectric thin films that have been widely investigated for ferroelectric random access memory (FRAM) applications, SrBi$_2$Ta$_2$$O_{9}$ thin film is appropriate to memory capacitor materials for its excellent fatigue endurance. However, very few studies on etch properties of SBT thin film have been reported although dry etching is an area that demands a great deal of attention in the very large scale integrations. In this study, the a SrBi$_2$Ta$_2$$O_{9}$ thin films were etched by using magnetically enhanced inductively coupled Ar/CHF$_3$ plasma. Etch properties, such as etch rate, selectivity, and etched profile, were measured according to gas mixing ratio of CHF$_3$(Ar$_{7}$+CHF$_3$) and the other process conditions were fixed at RF power of 600 W, dc bias voltage of 150 V, chamber pressure of 10 mTorr. Maximum etch rate of SBT thin films was 1750 A77in, under CHF$_3$(Ar+CHF$_3$) of 0.1. The selectivities of SBT to Pt and PR were 1.35 and 0.94 respectively. The chemical reaction of etched surface were investigated by X-ray photoelectron spectroscopy (XPS) analysis. The Sr and Ta atoms of SBT film react with fluorine and then Sr-F and Ta-F were removed by the physical sputtering of Ar ion. The surface of etched SBT film with CHF$_3$(Ar+CHF$_3$) of 0.1 was analyzed by secondary ion mass spectrometer (SIMS). Scanning electron microscopy (SEM) was used for examination of etched profile of SBT film under CHF$_3$(Ar+CHF$_3$) of 0.1 was about 85˚.85˚.˚.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.14-17
• /
• 2000

Giga bit dynamic random access memory(DRAM) requires the capacitor of high dielectric films. Some metal oxides films have been proposed as the dielectric material . And Pt is one of the most promising electrode materials. However very little has been done in developing the etching technologoy Pt film. Therefore, it is the first priority to develop the technology for plasma etching of Pt film. In this study, the dry etching of Pt film was investigated in Inductively Coupled Plasma(ICP) etching system with Cl$_2$/Ar and HBr/Cl$_2$/Ar gas mixing. X-ray photoelectron spectroscopy (XPS) was used in analysis of sidewall residues for the understanding of etching mechanism. We found the etch residues on the pattern sidewall is mainly Pt-Pt, Pt-Cl and Pt-Br compounds, Etch profile was observed by Scanning Electron Spectroscopy(SEM) . The etch rate of Pt film at 10%, Cl$_2$/90% Ar gas mixing ration was higher than at 100%. Ar. Addition of HBr to Cl$_2$/Ar as an etching gas led to generally higher selectivity to SiO$_2$. And the etch residues were reduced at 5% HBr/5% Cl$_2$/90% Ar gas mixing ration. These pages provide you with an examples of the layout and style which we wish you to adopt during the preparation of your paper, Make the width of abstract to be 14cm.