• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.200-207
• /
• 2001

Burrs farmed in drilling are classified into three types, no burr, burrs with cap, teared burr. To control burr size in drilling, the second type burrs with cap are to be formed because it is small and uniform. It is necessary to understand the mechanism of cap formation to derive the burr formation into second type burr with cap. In several materials. second type burrs are formed in drilling by changing cutting conditions. It is observed that cap is formed as a result of the plastic deformation along the outside of exit hope. According to the tension behavior of the material in concentrated region between hole and drill outside edge, the geometry of burr with cap is determined. Simplified 2D FEM analysis shows good prediction for burr formation.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.209-212
• /
• 2002

The wear process of end mill is a so complicated process that a more reliable technique is required for the monitoring and controling the tool life and its performance. This research presents a new tool wear monitoring method based on the sound signal generated on the machining. The experiment carried out continuous-side-milling for 4 cases using the high-speed steel slot drill under wet condition. The sound pressure was measured at 0.5m from the cutting zone by a dynamic microphone, and was analyzed at frequency domain. The tooth passing frequency appears as a harmonics form, and end mill wear is related with the first harmonic. It can be concluded from the result that the tool wear is correlate with the intensity of the measured sound at tooth passing frequency estimation of end mill wear using sound is possible through frequency analysis at tooth passing frequency under the given circumstances.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.1
• /
• pp.45-51
• /
• 2012

Sea ice properties have been considered a key indicator in the structural design criteria of icebreaking vessels and arctic offshore platforms to estimate design ice load and resistance for their safety management in Arctic Ocean. A measurement study of sea ice properties was conducted during July to August of 2011 with the Korean icebreaking research vessel "Araon" around Chukchi Borderland. The sea ice concentration appears to be rapidly decreasing during this cruise. Ice condition seems to be thick second-year ice and multi-year ice and then, a lot of melt ponds were observed in the surface of ice floe. Calculated flexural strength of sea ice was about 250~550kPa, ice thickness was roughly 1.3~3.0m. In this research we performed field experiment to measure ice temperature along the depth, thickness, density, salinity, brine volume ratio and crystal structure. Apparent conductivities derived with the electromagnetic induction instrument were compared to drill hole measurement results and accuracy of sea ice thickness estimation formula was discussed.

• Journal of Industrial Technology
• /
• v.29 no.B
• /
• pp.57-64
• /
• 2009

This study has analysed actual overbreak, shotcrete rebound and the ratio between the actual quantity of shotcrete to designed shotcrete measured during a NATM tunnel construction. The measured shotcrete rebound was about 7.2% in average which was about half the allowable rebound (15%), showing shotcrete spraying was performed well. Based on the measurement of excavated tunnel shape, average overbreak was about 28.5cm after tunnel excavation by drill and blasting method. This was about 260% of allowable overbreak. In addition, due to the rebound and overbreak actual amount of shotcrete used in the tunnelling work was about 116.5 % of the designed value. According to the field measurement the ratio of actual shotcrete to designed value showed some relation with standard support pattern, but the size of overbreak did not show the correlation with standard support pattern. Hence current design specifications stating the size of overbreak based entirely on standard support pattern should perhaps be reestablished. The insight into the design guideline regarding overbreak and shotcrete.

• Journal of The Korean Association of Information Education
• /
• v.7 no.2
• /
• pp.141-151
• /
• 2003

The purpose of this study was to design and develop a multimedia program for elementary school students' emergent literacy teaching. The program aims at helping students improve their reading ability and enhance their letter decoding ability through drill-and-practice as well as tutorial instructional strategies. To that end, the instructional materials were reorganized so as to provide a basic syllable table and writing examples with standard pronunciation. The multimedia program is composed of three sections: basic literacy teaching, advanced literacy teaching, and evaluation sections. The implications of the study were discussed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.12
• /
• pp.1210-1215
• /
• 2010

Unit cabin means room, which is installed in the high value-added vessel such as drill ship, offshore platform and FPSO, after pre-assembled. In order to develop the noise control design for a unit cabin, a variety of acoustic tests such as sound absorption, transmission and radiation measurements were carried out by using the deckhouse mock-up. From the tests, it was found out that the sound transmission loss between cabin and corridor was 13 dB below than FPSO standard and the combined noise level of the unit cabin was dominated by the radiated noise from wall panel in low frequency range. Based on the test results, design guidelines for the noise control of the unit cabin were fully established, such as the improvement of sound transmission loss between the cabin and corridor, and radiated cabin noise reduction.

• Tunnel and Underground Space
• /
• v.6 no.3
• /
• pp.197-208
• /
• 1996

Due to the constraints in pre site-investigation for tunnel, it is essential to redesign the support structures suitable for rock mass conditions such as rock strength, ground water and discontinuity conditions for safe tunnel construction. For the selection of optimum support, it is very important to carry out the rock mass classification and in-situ measurement in tunnelling. In this paper, in a mountain tunnel designed by NATM in hard rock, the selectable system for optimum support has been studied. The tunnel is situated at Chun-an in Kyungbu highspeed railway line with 2 lanes over a length of 4, 020 m and a diameter of 15 m. The tunnel was constructed by drill & blasting method and long bench cut method, designed five types of standard support patterns according to rock mass conditions. In this tunnel, face mapping based on image processing of tunnel face and rock mass classification by RMR carried out for the quantitative evaluation of the characteristics of rock mass and compared with rock mass classes in design. Also, in-situ measurement of convergence and crown settlement conducted about 30 m interval, assessed the stability of tunnel from the analysis of monitoring data. Through the results of rock mass classification and in-situ measurement in several sections, the design of supports were modified for the safe and economic tunnelling.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.31 no.3
• /
• pp.178-185
• /
• 2015

Purpose: The purpose of this study was to conduct a comparative assessment on the satisfaction level for the two interfaces of surgical guide system (SimPlant and R2GATE), the design and convenience of manufactured surgical guides and the importance of using the surgical guides thereof by means of survey. Materials and Methods: Hereupon, they simulated the implant surgical process by mounting the two manufactured systems of surgical guide on a dental mold, respectively. The study subjects were instructed to complete the questionnaire as to the satisfaction level upon completion of the simulated surgery. This study summarized the data of each question after collecting the completed questionnaires. Then, this study analyzed the summarized data by utilizing statistical program SPSS 20.0 (IBM). Results: R2GATE had a higher value of the satisfaction level on the design and convenience of manufactures surgical guides. R2GATE group ($7.33{\pm}1.26$) was found to have a higher value in terms of the overall satisfaction level compared to SimPlant group ($6.67{\pm}1.26$) (${\alpha}$ = 0.05). Conclusion: The user satisfaction level on the surgical guide manufactured for R2GATE system was to such an extent as it can be widely used in clinical environment. Moreover, the surgical guide manufactured as R2GATE system can guide both the length and direction of a drill simultaneously. As a result, it is highly recommended for those beginners who do not have a lot of experience in implant placement.

• The Journal of the Korea Contents Association
• /
• v.17 no.3
• /
• pp.222-230
• /
• 2017

The Ministry of Public Safety and Security plans to expand fire safety education infrastructure to provide customized fire safety education, spread fire safety culture and develop a tailored fire safety education system as a part of the 2016 Citizens' Safety Improvement Policy. This study has also been designed to improve safety problems in the Republic of Korea. Even though safety education has been given, citizens aren't still able to experience a close-to-real situation. In addition, their understanding and satisfaction with the curriculum are very low. Therefore, this study offers VR fire-extinguishing experience education contents as an effective alternative. With a goal of having the participants experience fire extinguishing and evacuation drill in a virtual space, this program has the following advantages: i) safe fire-extinguishing experience; ii) UI to create fun ; iii) useful in fire-extinguishing education; iv) budget saving. we configure the VR fire experience system structure and hardware by applying UX design methodology. We also develop for VR-specific motion recognition plug-in and controller that can be feeling in HMD environment.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.1 s.160
• /
• pp.1-10
• /
• 2007

This research was designed to compare the subjective evaluation of Hand between on- and off-line by structure and sensible characteristics of fabric. 113 subjects who have a fashion design major evaluated the subjective evaluation of Hand of various 16 kinds of specimens on- and off-line. T-test and pearson correlation coefficient were used for statistical analysis by SPSS WIN 11.0. The results of this study were as follows: The results of correlation analysis of the evaluation score indicated that Crash and Satin show high correlation between two kinds of evaluation score. But, fabrics which have distinct characteristics such as Plush, Dobby, Seersucker represented low correlation coefficient. The results of t-test fer the difference of the evaluation score showed that thin fabrics like Organdy represent a large difference between on- and off-line evaluation. On the other hand, twill weaved fabrics like Drill, Tweed, Saxony did not show many differences. Analysing each item in terms of correlation of evaluation of hand between on- and off-line gave results that the shininess was most deliverable through on-line and density and the dryness was not so deliverable through on-line. Comparison of evaluation score between on- and off-line items showed that the estimation to real fabric is more negative than that of on-line. The results of most preferable hand between on-and off-line showed exact opposite preference between shinny, smooth and soft Satin and rough, woolen Tweed. Organdy showed the most different subjective evaluation of hand in real ones compared with that of on-line.