• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.2
• /
• pp.71-79
• /
• 2019

Geolocation accuracy is one of the important factors in utilizing all weather available SAR satellite imagery. In this study, an error budget analysis was performed on key variables affecting on geolocation accuracy by generating KOMPSAT-5 simulation data. To perform the analysis, a Range-Doppler model was applied as a geometric model of the SAR imagery. The results show that the geolocation errors in satellite position and velocity are linearly related to the biases in the azimuth and range direction. With 0.03cm/s satellite velocity biases, the simulated errors were up to 0.054 pixels and 0.0047 pixels in the azimuth and range direction, and it implies that the geolocation accuracy is sensitive in the azimuth direction. Moreover, while the clock drift causes a geolocation error in the azimuth direction, a signal delay causes in the range direction. Monte-Carlo simulation analysis was performed to analyze the influence of multiple geometric error sources, and the simulated error was up to 3.02 pixels in the azimuth direction.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.350-361
• /
• 1995

For the Purpose of the measurement of drifting condition of the anchovy drift gill net, some experiments were carried out in M. S Seong-Yang at the near sea of Kampo harbor in Korean east sea from August to October 1994, by using three set of GPS equipped with her net. The main results obtained are as follows : 1) In fixed position by GPS at Taebyon, the radius of 95% probability and shifted distance from standard position were respectively 79.8m, 21.0m. 2) The mean values of PDOP and HDOP of GPS at Taebyon were respectively 3.5, 1.9 and the stability of the position by GPS at Taebyon was found to be very high. 3) In the fishing ground of the position from Lat. $35^{\circ}$ 41.5'N to $Lat^{\circ}$. 43.5', from Long. $129^{\circ}$ 32.0'E to Long. $129^{\circ}$ 32.5'E, the direction of the whole stretched drift gill net was $190^{\circ}$ and the direction of the whole casted net was $200^{\circ}$ when casting the net was finished. When whole net was found to be drifting into the direction of $170^{\circ}\;to\;180^{\circ}$, and the mean drifting speed of that was 0.82kt. 4) In the fishing ground of the position from Lat. $35^{\circ}$ 44.0'N to Lat. $35^{\circ}$ 45.2'N, from Long. $129^{\circ}$ 30.1'E to Long. $129^{\circ}$ 31.2'E, the direction of the whole stretched net was 20$^{\circ}$ and the direction of the whole stretched net was $20^{\circ}$ when casting the net was finished. When hauling the net, the direction of the spreaded net appeared from the North into the South and the whole net was found to be drifting into the direction of $210^{\circ}\;to\;220^{\circ}$, and the mean drifting speed of that was 0.75kt. 5) In the fishing ground of the positioning from Lat. $35^{\circ}$ 44.9'N to Lat. $35^{\circ}$ 46.0'N, Long. $129^{\circ}$ 33.0'E to Long. $129^{\circ}$ 34.0'E, the direction to the whole stretched net was $35^{\circ}$ and the direction of the whole casted net was $50^{\circ}$ when casting the net was finished. When hauling the net, the direction of the spreaded net appeared into the South from the East and the whole net was found to be drifting into the direction of $330^{\circ}\;to\;40^{\circ}$, and the mean drifting speed of the was 0.63kt.

• Journal of Navigation and Port Research
• /
• v.26 no.2
• /
• pp.221-226
• /
• 2002

To provide reliable data for drift prediction models, field experiments were carried out in the coastal region off Busan port. Four different size of vessels(10, 30, 50, 90G/T ton) were deployed for the experiment. Among them G/T 50ton class vessel was equipped with instruments measuring the currents, winds, headings and trajectory data. In the rest of vessels only the position data were recorded for the purpose of target divergence study. The trajectories of each vessel were measured by DGPS(Differential Global Positioning System) and collected by APRS(Automatic Position Reporting System). The experiment was done in wind of 2~10m/s and current of 0.5~1.5m/s. The leeway was derived by subtracting surface current velocity from target drifting velocity. The leeway rate of G/T 50ton vessel was found to be about 3.6% and the computed leeway speed equation was $U_L$=0.042 W - 0.034. The processed leeway angle data were deflected by $-30^{\circ}$~$40^{\circ}$ from the direction of ship drift.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.4
• /
• pp.373-381
• /
• 1997

In order to investigate the drift of pesticides sprayed on Chinese cabbage, 7 pesticides chlorpyrifos, EPN, pirimiphos-methyl, phenthoate, tetradifon, dicofol and bifenthrin were applied in two sets of field tests. The pesticide residues were quantified bar multiple-residue analysis, in which the recovery rate was 78${\sim}$92% and standard deviation was ${\pm}0.683{\sim}52%$. It was found that most of the tested pesticides were spread by drift to neighbouring area and brought about the contamination of the unsprayed crops. The extent of drift varied depending upon the pesticide, distance and wind direction. The mean residue levels on unsprayed crops were 0.66% at 3 meter distance, 0.10% at 6 m distance and 0.05% at 9 m distance from the applied area and the maximum level was 1.83% of the residue on sprayed crops.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.93-101
• /
• 2008

Bearing strength test was investigated to determine the bearing properties of domestic larix glulam according to the load direction (in parallel to grain and in perpendicular to grain), the fastener (bolt and drift-pin), and the direction of laminae. The specimen was 5 ply glulam. The diameters of fastener are 12, 16 and 20 mm. The results were as follows. 1) In according to the diameter of bolt and drift-pin, the average of maximum bearing strength in parallel to grain loading was similar to that in perpendicular to grain loading. The average of maximum bearing strength was 1.50~2.31 times higher in parallel to grain loading than in perpendicular to grain loading. The average of maximum bearing strength in parallel to grain loading was lowered by 20% with increasing the diameter from 16 mm to 20 mm, but that in perpendicular to grain loading didn't show a clear tendency. 2) The average of bearing stiffness in parallel to grain loading was the highest at 16 mm in diameter. The average of bearing stiffness is similar to the shearing stiffness in drift-pin connection with increasing diameter. 3) In parallel to grain loading, the failure mode of specimens was the splitting along the grain in decreasing diameter. The failure mode in perpendicular to grain loading was the splitting along the grain. In this case, split occured more in specimens using bolt than in those using drift-pin. 4) The 5% offset yield strength in parallel to grain loading was similar to the predicted bearing strength of KBCS, NDS. In perpendicular to grain loading, the NDS's equation can be applied to predict the bearing strength.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.69-78
• /
• 2008

Shearing strength test in tension type was investigated to determine the shear resistance of bolt and drift-pin connection of domestic larix glulam. The specimen was connected with bolt and drift-pin in the inserted plate type, and only bolt in the side plate type. The diameter of bolt and drift-pin used in the experiment are 12, 16 and 20 mm. The hole of bolt was drilled at the end-distance 5 d and 7 d. Tension load was loaded in the direction parallel to grain. The shear resistance was evaluated according to end-distance through this, the yield load was compared with the experimental yield load, using Larsen's formula. The prototype design strength is based on the yield load of end-distance 7 d and the reduction factor of end-distance 5 d was calculated. The results were as follows. 1. The average of maximum load of drift-pin connection was higher by 3~30% at the inserted type than at bolt connection with increasing diameter. In bolt connection, the average of maximum load of the side type was 1.54~2.07 times higher than that of the inserted type. In the same diameter, the average of maximum load of end-distance 7 d was higher by 8~44% than that of 5 d. 2. The bearing stress was 1.16~1.41 times higher at the inserted connection than at drift-pin connection, and 1.37~1.86 times higher at 7 d than at 5 d. Also, when the slenderness ratio was below 7.5 at drift-pin connection and below 6.0 at inserted connection, the lateral capacity was good. 3. The ratio of the experimental yield load and the predicted yield load calculated by Larsen's formula proposed by Larsen was 0.80~1.10 at inserted connection, and 0.75~1.46 at side connection. 4. When the inserted bolt connection was based on the yield load of end-distance 7 d, the reduction factor was 0.89 at 12 mm connection, 0.93 at 16 mm and 0.85 at 20 mm. The reduction factor was 0.89 at 12 mm the inserted drift-pin connection, 0.93 at 16 mm, 0.93 at 20 mm. The reduction factor was 0.79 at the side connection of the 12 mm bolt connection and 0.80 at 16 mm.

• Journal of Advanced Research in Ocean Engineering
• /
• v.4 no.2
• /
• pp.53-65
• /
• 2018

The load condition significantly influences ship maneuverability in calm water. In this research, the effect of the load condition on turning performance of a very large crude oil carrier (VLCC) sailing in adverse weather conditions is investigated by an MMG-based maneuvering simulation method. The relative drift direction of the ship in turning to the wave direction is $20^{\circ}-30^{\circ}$ in ballast load condition (NB) and full load condition (DF) with a rudder angle $35^{\circ}$ and almost constant for any wind (wave) directions. The drifting displacement in turning under NB becomes larger than that under DF at the same environmental condition. Advance $A_d$ and tactical diameter $D_t$ become significantly small with an increasing Beaufort scale in head wind and waves when approaching, although $A_d$ and $D_t$ are almost constant in following wind and waves. In beam wind and waves, the tendency depends on the plus and minus of the rudder angle.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.1
• /
• pp.95-105
• /
• 1997

This paper presents a Inertial Measuring Unit(IMU) for motion measurement of an AUV. The IMU is composed of three parts: inertial sensors with three servo accelerometers and three rate gyros, an analog/digital interface board, and a signal processing board with TMS320C31 DSP processor. The IMU is a class of strap-down inwetial navigation system does not applicable directly to the navigation system in consequence of the AUV and integrated sensors for an integrated navigation system of the AUV. Fast calculstion of direction cosine matrix for the coordinate transformation body to reference is obtained through the DSP processor. A switching algotrithm is used to lessen the low frequency drift effect of the gyros in the vertical plane with use of low pass filtering of the signal of the accelerometers.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.29
• /
• pp.3-37
• /
• 2006

This writing is for the purpose of investigating the specific character and problem point of China arbitration system which has near 90 years history and overviewing the drift of system improvement which happens recently. The arbitration system of China which traditionally does not acknowledge ad hoc arbitration, unlike most of the other nations that employ The UNCITRAL model law and make it their own legislation, is restrictive to the parties concerned principle of private autonomy considerably. Also the independence of arbitration is delicate, because of a civil characteristic weakness of the arbitral institutions and the intervention of the courts on the arbitration procedure and award. The dual system of domestic and international arbitration which maintains after enforcement of 1994 arbitration law is often to be a primary factor interrupting the development of Chinese arbitration system and making it vulnerable to challenges. The system improvement demand of the recent time reflects this point and makes the arbitration system of China to a international standard rather than now, so it is a desirable direction for China to be as the member of the world economy to be globalization.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.209-216
• /
• 2003

The purpose of this study is to investigate the response characteristics of pushover analysis of upper wall-lower frame system with X and Y-directions' lateral load Pushover analysis estimates initial elastic stiffness, post-yielding stiffness, and plastic hinges on each story of structures through three-dimensional nonlinear analysis program. The conclusions of this study are as follows; (1) As a result of pushover analysis, the magnitude of nonlinear response and distribution of yield hinge in lower structure are similar with both X and Y directions, but not in upper structure because of different relative stiffness. (2) The maximum drift ratio of roof is larger for X-direction than for Y-direction with respect to magnitude of shear wall areas in upper structure.