• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.263-266
• /
• 2003

The high power factor converters are classified step-up, step-up-down and step-down converter, The power conversion system must be increased switching frequency in order to achieve a small size, a light weight and a low noise. And the power system brings on a high efficiency and high power factor. When a switch of the step down converter is operated with a commercial frequency(60Hz), a reactor using the converter is gone with a great number of harmonics waveforms of low grade. As results of this, the converter is decreased input power factor and is increased system size. To improved these, this paper proposes a PSM(Pulse Size Modulation) control strategy operated with high power factor.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.261-264
• /
• 2005

This paper presents the design of a down-conversion mixer with built-in active balun integrated in a $0.25\;{\mu}m$ pHEMT process. The active balun consists of series-connected common-gate FET and common-source FET. The designed balun achieved broadband characteristics by optimizing gate-width and bias condition for the reduction in parasitic effect. From DC to more than 6GHz, the active balun shows the phase error of less than 3 degree and the gain error of less than 0.4 dB. A single-balanced down-conversion mixer with built-in broadband active balun has been designed with optimum width, load resistor and bias for conversion gain and without any matching component for broadband operating. The designed mixer whose size of including on-chip bias circuit is $1\;mm{\times}1\;mm$ shows the conversion gain of better than 7 dB from 2 GHz to 6 GHz and $P_{1dB}$ of -10 dBm at 5.8 GHz

• Journal of the Korean Ceramic Society
• /
• v.54 no.1
• /
• pp.70-74
• /
• 2017

Up-conversion (UC) and down-conversion (DC) luminescence of $LuNbO_4:0.18Yb^{3+}$, $xEr^{3+}$ (x = 0.01-0.07) powders were investigated. Post-annealed powders were composed of a single $LuNbO_4$ phase with a monoclinic fergusonite structure, whereas as-calcined powders contained a small amount of the $Li_3NbO_4$ impurity phase. Under near infrared radiation, the UC spectra of the post-annealed powders exhibited the strong green and weak red emission peaks assigned to the transition of $^2H_{11/2}/^4S_{3/2}$ and $^4F_{9/2}$ to the ground state ($^4I_{15/2}$) of $Er^{3+}$ ions, respectively; the green and red emission intensities were approximately 330 and 270% stronger, respectively, than those of the as-calcined powders. A two-photon UC process was involved in the emission as a result of an energy transfer from $Yb^{3+}$ to $Er^{3+}$. Under ultraviolet radiation, the DC spectra exhibited broad blue and sharp green emission bands. The DC mechanism was explained using self-activated $[NbO_4]^{3-}$ niobates and an energy transfer from $[NbO_4]^{3-}$ to $Er^{3+}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1318-1323
• /
• 2010

A lot of demand for parts of millimeter wave band, as would be expected 57~63 GHz band down conversion mixer was designed and fabricated using IHP 0.25 um SiGe process. Designed and fabricated mixer was double balanced type and located reduced 3D balun at RF port and buffer amplifier at outport for suppression LO signal and conversion gain. Fabricated mixer measured conversion gain of 13.8 dB, $P1dB_{in}$ -17 dBm and 88 mA of current consumption characteristics, respectively.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1998.10a
• /
• pp.487-490
• /
• 1998

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.08a
• /
• pp.196-197
• /
• 2001

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.89-92
• /
• 2004

For improving solar efficiencies, down conversion of high-energy photons to visible lights is discussed. The losses due to thermalization of charge carriers generated by the absorption of high-energy photons, can largely be reduced in a solar cell if more than one electron-hole pair can be generated per incident photon. The solar cell was constructed of dye-sensitized anatase-based TiO$_2$, approximately 30nm particle size, 6$\mu\textrm{m}$thickness, and 6${\times}$6$\textrm{mm}^2$ active area, Pt counter electrode and I$_3$$\^$-/I$_2$$\^$-/ electrolyte. After correction for losses due to light reflection and absorption by the conducting glass, the conversion of photons to electric current is practically quantitative in the plateau region of the curves. The incident photon to current conversion efficiency(IPCE) of N3 used as a dye in this work is about 80% at around 590nm and 610nm which is the emission spectrum of Eu doped LGF. The Eu doped LGF powder was prepared by conventional ceramic process, and used as a down converter for DSC after spin coated on the slide glass and fired.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.43-50
• /
• 2010

DDC(Digital Down Converter) is a conversion technology to decimate to a lower sampling rate and DDC for the future development of communications technology has the necessary skills. So, it has been recognized in the wireless and the SDR(Software Defined Radio) system as essential components. In addition, research is underway on spectrum sensing for efficient communications environment due to the shortage of frequency resources. In this paper, the DDC systems were analyzed for CIC(Cascaded Integrator Comb) Filter, WDF(Wave Digital Filter), SRC(Sample Rate Conversion) each module. Moreover, we proposed a linkage effectively between DDC system and Spectrum Sensing for improve the efficiency of use of frequency by computer simulations. The simulation results of the DDC system was applied to the spectrum sensing capabilities. Also, performance and complexity of the results were derived and proposed system was the result of the check.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.8C
• /
• pp.806-815
• /
• 2006

It is studied to design a low pass filter of the SRC(sample rate converter), which is used to change the sampling rate of digital signals such as in digital modulation and demodulation systems. The larger the conversion ratio of the sample rate becomes, the more signal processing is needed for the filter, which corresponds to the more complexity in circuit realization. Thus it is important to reduce the amount of signal processing for the case of high conversion ratio. In this paper it is presented a design method of a two-stage cascaded FIR filter, which proved to have reduced amount of signal processing in comparison with a conventional single-stage one. The reduction effect of signal processing turned out to be more noticeable for larger value of conversion ratio, for instance, giving down to 72% in complexity for the conversion ratio of 32. It has been shown that the reduction effect is dependent to specific combination of conversion ratios of the cascaded filters. So an exhaustive search has been performed in order to obtain the optimal combination for various values of the total conversion ratio. In this paper every filter is considered to be implemented in the form of a polyphase FIR filter, and its coefficients are determined by use of the Parks-McCllelan algorithm.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.356-363
• /
• 2018

The combination of a buck converter and a forward converter can be considered to accomplish a high step-down non-isolated converter. To decrease the insufficient step-down ratio of a regular buck converter and to distribute switch voltage stress, a forward-integrated buck (FIB) converter is proposed in this paper. The proposed interleaved DC-DC converter provides an additional step-down gain with the help of a forward converter. In addition to its simple structure, the transformer flux reset problem is solved and an additional magnetic core reset winding is not required. The operational principle and an analysis of the proposed FIB converter are presented and verified by experimental results obtained with a 240 W, 150 V/24 V prototype.