• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.689-692
• /
• 1999

This paper describes a 10-bit 75-MHz CMOS current-mode DAC designed for 0.8${\mu}{\textrm}{m}$ double-poly double-metal CMOS technology. This D/A converter is implemented using a current cell matrix that can drive a resistive load without output buffer. In the DAC. a current source is proposed to reduce the linearity error caused by the threshold-voltage variations over a wafer and the glitch energy caused by the time lagging, The integral and differential linearity error are founded to be within $\pm$0.35 LSB and $\pm$0.31 LSB respectively. The maximum conversion rate is about 80 MS/s. The total power dissipation is 160 ㎽ at 75 MS/s conversion rate.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.194-201
• /
• 2015

A frequency modulated ultra-wideband (FM-UWB) transmitter with a high-robust relaxation oscillator for subcarrier generation and a dual-path Ring VCO for RF FM is proposed, featuring low power and low complexity. A prototype 3.65-4.25 GHz FM-UWB transceiver employing the presented transmitter is fabricated in $0.18{\mu}m$ CMOS for short-range wireless data transmission. Experimental results show a bit error rate (BER) of $10^{-6}$ at a data rate of 12.5 kb/s with a communication distance of 60 cm is achieved and the power dissipation of 4.3 mW for the proposed transmitter is observed from a 1.8 V supply.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.40-46
• /
• 2010

This paper describes a clock and data recovery (CDR) circuit that supports dual data rates of 2.7Gbps and 1.62Gbps for DisplayPort standard. The proposed CDR has a dual mode voltage-controlled oscillator (VCO) that changes the operating frequency with a "Mode" switch control. The chip has been implemented using $0.18{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of 37ps(@2.7Gbps) and 27ps(@1.62Gbps) in the recovered data. The power dissipation is 80mW at 2.7Gbps rate from a 1.8V supply.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.771-776
• /
• 2000

Fine grid calculations are reported for the developing turbulent flow in a straight duct and a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=R_c/H_H=3.357$ and a bend angle of 180 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.139-146
• /
• 1996

An extended $k-\varepsilon$ tuebulence model modified by considering the streamline curvature effect and standard $k-\varepsilon$ turbulence model have been applied for three dimensional analysis of turbulece flow in a $90^{\circ}$ curved duct. By comparision of the results with the experimental data, the modified extended $k-\varepsilon$ model gave closer agreement with experimental data than the results from standard $k-\varepsilon$ model owing to an extra time scale of the production rate and parameter describing effects of streamline curvature included in the dissipation rate equation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.4
• /
• pp.337-342
• /
• 2000

We fabricated resistive superconducting fault current limiters based on YB $a_{2}$/C $u_{3}$/ $O_{7}$ thin films and investigated their quench propagation characteristics. The YB $a_{2}$/C $u_{3}$/ $O_{7}$ films was coated with a gold layer and patterned into 1 mm wide meander lines by photolithography. The quench was concluded to start locally and propagates until completed. The quench propagation characteristics were explained based on the heat transfer within the film as well as between the film and the surrounding liquid nitrogen. The quench completion time depended strongly on potential fault current amplitude and not significantly on fault angle which indicates that the quench propagation speed is affected more by heat dissipation rate than by fault current increase rate. The quench completion time was 1 msec at the fault current of 65 $A_{peak/{\ak}}$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.10
• /
• pp.1025-1033
• /
• 2001

A scaling analysis is provided which predicts the sliding velocity of a liquid drop down an inclined surface. The analysis is based on the balance of the gravitational work rate that drives the drop sliding and the resistances by capillary and viscous forces. The capillary resistance is accounted for via the contact angle hysteresis, which is quantified by measuring the critical inclination causing the drop to start sliding. The sliding of the drop is governed by the rate of the viscous dissipation of the Stokes flow. The analysis result in its limit form for small contact angles is consistent with previous results. In the experiments to verify the analysis results, the measured sliding velocity of various liquid drops are shown to obey the predictions made in this study.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2297-2307
• /
• 1995

An experimental study on the structure of a separated shear layer downstream of the backward-facing step has been performed by examining mean flow and turbulent quantities in terms of free stream turbulence. When free stream turbulence exists, the entrainment rate of the separated shear layer and the flow rate in the recirculation region are enhanced, resulting in shorter reattachment length. The production and diffusion terms in the turbulent kinetic energy balance are shown to increase more than the dissipation term does. Rapid decrease of the pressure-strain term in the shear stress balance implies the enhancement of the three-dimensional motion by free stream turbulence.

• Geomechanics and Engineering
• /
• v.12 no.2
• /
• pp.313-326
• /
• 2017

Based on the reliability theory and limit analysis method, the roof stability of a shallow tunnel is investigated under the condition of surface settlement. Nonlinear Hoek-Brown failure criterion is adopted in the present analysis. With the consideration of surface settlement, the internal energy and external work are calculated. Equating the rate of energy dissipation to the external rate of work, the expression of support pressure is derived. With the help of variational approach, a performance function is proposed to reliability analysis. Improved response surface method is used to calculate the Hasofer-Lind reliability index and the failure probability. In order to assess the validity of the present results, Monte-Carlo simulation is performed to examine the correctness. Sensitivity analysis is used to estimate the influence of different variables on reliability index. Among random variables, the unit weight significantly affects the reliability index. It is found that the greater coefficient of variation of variables lead to the higher failure probability. On the basis of the discussions, the reliability-based design is achieved to calculate the required tunnel support pressure under different situations when the target reliability index is obtained.

• Journal of electromagnetic engineering and science
• /
• v.4 no.2
• /
• pp.56-62
• /
• 2004

We present a multi-Gbit/s digital I/O interface based on RF-modulation and capacitive-coupling over an impedance matched transmission line. The RF-interconnect(RFI) can greatly reduce the digital switching noise and eliminate the dc power dissipation over the channel. It also enables reduced signal amplitude(as low as 200 ㎷) with enhanced data rate and affordable circuit overhead. This paper addresses the system advantages and implementation issues of RFI. A prototype on-chip RFI transceiver is implemented in 0.18-${\mu}{\textrm}{m}$ CMOS. It demonstrates a maximum data rate of 2.2 Gbit/s via 10.5-㎓ RF-modulation. The RFI can be very instrumental for future high-speed inter- and intra-ULSI data links.