• 한국산학기술학회논문지
• /
• 제17권8호
• /
• pp.706-713
• /
• 2016

본 연구에서는 이종소재 A6005-AZ61 접합을 위하여 마찰교반용접의 툴 삽입 위치와 모재의 냉각 유 무에 따라 용접부 특성을 분석하였다. 다른 용접 조건들인 툴 회전속도와 이송속도는 500rpm-30mm/min으로 고정하고 Advancing side에 알루미늄 합금(A6005), Retreating side에 마그네슘 합금(AZ61)을 배치하여 용접을 진행하였다. 용접은 여섯 가지 케이스를 진행하였다. 용접부 특성을 관찰하기 위하여 인장 시험을 진행하고, 광학현미경을 사용하여 용접부의 미세조직을 관찰하였다. 인장시험 결과 마그네슘 합금 방향으로 툴을 1mm 이동시키고 모재에 냉각을 시킨 조건에서 강도가 가장 높게 나타났다. 동일한 용접 조건에서 냉각을 한 경우에 냉각을 하지 않은 것 보다 강도가 약 2배 높게 측정되었다. 툴의 위치는 용접부 중심에서 알루미늄 합금 방향으로 1.7mm, 마그네슘 합금 방향으로 1.7mm 이동시켜 과도한 편심을 적용한 용접 조건에서는 교반이 잘 이루어지지 않아 용접부의 건전성이 가장 좋지 않았다. 과도한 편심을 적용한 용접 조건에서는 교반이 잘 이루어지지 않아 용접부의 건전성이 가장 좋지 않았다. 본 연구를 통해 A6005-AZ61 이종 마찰교반용접시 용접속도와 툴 회전속도만큼 모재의 온도 조절과 툴 삽입위치가 중요한 용접변수임을 확인 하였다.

• Coupled systems mechanics
• /
• 제7권5호
• /
• pp.627-634
• /
• 2018

Laser beam welding is more advantageous compared to conventional methods. Titanium/Aluminium dissimilar alloy thin sheet metals are difficult to weld due to large difference in melting point. The performance of the weldment depends upon interlayer formation and distribution of intermetallics. During welding, aluminium gets lost at the temperature below the melting point of titanium. Therefore, it is needed to improve a new metal joining techniques between these two alloys. The present work is carried for welding TI6AL4V and AA2024 alloy by using Nd:YAG Pulsed laser welding unit. The performance of the butt welded interlayer structures are discussed in detail using hardness test and SEM. Test results reveal that interlayer fracture is caused near aluminium side due to low strength at the weld joint.

• Journal of Welding and Joining
• /
• 제28권5호
• /
• pp.15-19
• /
• 2010

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.98-105
• /
• 2012

The focus of this investigation is to evaluate the effect of joining parameter on the microstructure and mechanical properties of welds produced by friction stir lap welding. The dissimilar Al alloys, KS5J32 and AA6K31, were joined by friction stir lap welding technique under several welding conditions, and KS5J32 alloy was placed on the top of AA6K31 alloy. The tool rotation speeds were 1000, 1250, and 1500rpm, and the welding speeds were 100, 300, 500, 700mm/min, respectively. The results showed that two shapes of nugget, such as onion ring and irregular vortex type, were observed with various revolutionary pitch. In all welding conditions, fracture occurred at the soften region of bottom sheet(AA6K31) and the strengths were 64~78% of those of base metal. Fractured positions were classified into three types : HAZ, triple point, void depending on the revolutionary pitch. The actual thickness of specimen at the fractured location was decreased with decreasing heat input. A linear relationship exists between the effective thickness of fractured position and peak load.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.302-307
• /
• 2013

A5J32-T4 and A5052-H32 dissimilar aluminum alloy plates with thickness of 1.6 and 1.5 mm were welded by friction stir lap welding (FSLW). The FSLW were studied using different probe length tool and various welding conditions which is rotation speed of 1000, 1500 rpm and welding speed of 100 to 600 mm/min and material arrangement, respectively. The effects of plunge depth of tool and welding conditions on tensile properties and weld nugget formation. The results showed that three type nugget shapes such as hooking, void, sound have been observed with revolutionary pitch. This plunge depth and material arrangement were found to effect on the void and hooking formation, which in turn significantly influenced the mechanical properties. The maximum joint efficiency of the FSLWed plates was about 90% compared to base metal, A5052-H32 when the A5052-H32 was positioned upper plate and plunge depth was positioned at near interface between upper and lower plates.

• 열처리공학회지
• /
• 제29권2호
• /
• pp.66-74
• /
• 2016

In this study, characteristics of TiAl alloy and SCM440 (Cr-Mo steel) have been investigated with the various joining condition by servo motor type friction welder. The experimental factors of friction welder used in this study are spindle revolution, friction speed, and distance, upset speed and distance, respectively. Servo motor type friction welder could be controlled by the level of oil pressure, and it could be performed by position control dependence of electrical energy. Mechanical properties and morphology of welded interface were characterized by various joining condition. This aroused due to the bond strength dependence on friction heat and size of the heat affected zone. Therefore, it is necessary to have enough friction heat and decreased heat affected zone for good friction welding between dissimilar metals. An optimum bond was obtained between TiAl alloy and SCM440 by controlling friction speed and distance. At the spindle revolution 4,000 rpm, friction speed 120 mm/min, friction distance 15 mm, the bond strength was found to be 312 MPa.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.28-29
• /
• 2008

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.417-422
• /
• 2021

In the present work, Inconel 718 alloy is additively manufactured on the Ti-6Al-4V alloy, and a functionally graded material is built between Inconel 718 and Ti-6Al-4V alloys. The vanadium interlayer is applied to prevent the formation of detrimental intermetallic compounds between Ti-6Al-4V and Inconel 718 by direct joining. The additive manufacturing of Inconel 718 alloy is performed by changing the laser power and scan speed. The microstructures of the joint interface are characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and micro X-ray diffraction. Additive manufacturing is successfully performed by changing the energy input. The micro Vickers hardness of the additive manufactured Inconel 718 dramatically increased owing to the presence of the Cr-oxide phase, which is formed by the difference in energy input.

• 열처리공학회지
• /
• 제16권1호
• /
• pp.2-9
• /
• 2003

The aluminum alloy which is light and has excellent thermal conductivity and iron base alloy that is remarkable heat-resistece and wear resistence properties were bonded together. The bond was created between a stationary and a rotating member by using the frictional heat generated between them while subjected to high normal forces on the interface of Al alloy and iron base alloy. The microstructure of the bonded interface of friction welding and the strength in the bonded interface formed under various bonding conditions were examined through TEM, SEM with EDX and triple bending test. In interface of bonding materials formed after various heat treatment, bonding strength was substantially different, resulting from formation of intermetallic compound or softening during annealing.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.108-113
• /
• 2010

Decreasing products lifecycles and increasing consumers desires for quality and design make the automotive industries try to reduce time for developing new designs. In order to reduce developing time, I have designed head lamps, which are really important to have an effect on brand identities and images, using layers concept that is one of the international automotive design trends by alias and photoshop, and produced prototype by RP. To assemble the produced prototype to the body and manufacture the frame to exterior modelling efficiently, I have studied on joining dissimilar materials of aluminum alloy that can make the prototype lighter and stainless steel, which is good for corrosion resistance by using laser beam. These materials were welded for finding the optimum joining condition and evaluating the soundness of joining zone. The joining was performed under the condition of laser power 500, 550, 575, 600W and 11~14Hz. In this study, the suitable joining condition between aluminum alloy (Al 2024) and stainless steel (STS 304) can be obtained at the laser power 575W and frequency 12Hz.