• Clean Technology
• /
• v.24 no.4
• /
• pp.371-379
• /
• 2018

The objective of this study is to develop a platinum/hexaaluminate pellet catalyst for the decomposition of eco-friendly liquid propellant. Pellet catalysts using hexaaluminate prepared by ultrasonic spray pyrolysis as a support and platinum as an active metal were prepared by two methods. In the case of the pellet catalyst formed by loading the platinum precursor onto the hexaaluminate powder and then adding the binder (M1 method catalyst), the mesopores were well developed in the catalyst after calcination at $550^{\circ}C$. However, when this catalyst was calcined at $1,200^{\circ}C$, the mesopores almost collapsed and only a few macropores existed. On the other hand, in the case of a catalyst in which platinum was supported on pellets after the pellet was produced by extrusion of hexaaluminate (M2 method catalyst), the surface area and the mesopores were well maintained even after calcination at $1,200^{\circ}C$. Also, the catalyst prepared by the M2 method showed better heat resistance in terms of platinum dispersion. The effects of preparation method and calcination temperature of Pt/hexaaluminate pellet catalysts on the decomposition of liquid propellant composed mainly of ammonium dinitramide (ADN) or hydroxyl ammonium nitrate (HAN) were investigated. It was confirmed that the decomposition onset temperature during the decomposition of ADN- or HAN- based liquid propellant could be reduced significantly by using Pt/hexaaluminate pellet catalysts. Especially, in the case of the catalyst prepared by the M2 method, the decomposition onset temperature did not show a large change even when the calcination temperature was raised at $1,200^{\circ}C$. Therefore, it was confirmed that Pt/ hexaaluminate pellet catalyst prepared by M2 method has heat resistance and potential as a catalyst for the decomposition of the eco-friendly liquid propellants.

• Journal of Powder Materials
• /
• v.20 no.2
• /
• pp.142-147
• /
• 2013

$YBa_2Cu_3O_{7-y}$ (Y123) powders for the fabrication of bulk superconductors were synthesized by the powder reaction method using $Y_2O_3$ (99.9% purity), $BaCO_3$ (99.75%) and CuO (99.9%) powders. The raw powders were weighed to the cation ratio of Y:Ba:Cu=1:2:3, mixed and calcined at $880^{\circ}C-930^{\circ}C$ in air with intermediate repeated crushing steps. It was found that the formation of Y123 powder was more sensitive to reaction temperature than reaction time. The calcined Y123 powder and a mixture of (Y123 + 0.25 mole $Y_2O_3$ + 1 wt.% $CeO_2$, $Y_{1.5}Ba_2Cu_3O_x$ (Y1.5)) were used as raw powders for the fabrication of poly-grain or single grain superconductors. The superconducting transition temperature ($T_{c,onset}$) of the sintered Y123 sample was 91 K and the transition width was as large as 11 K, whereas the $T_{c,onset}$ of the melt-grown Y1.5 sample was 90.5 K and the transition width was 3.5 K. The critical current density ($J_c$) at 77 K and 0 T of the sintered Y123 was 700 $A/cm^2$, whereas the $J_c$ of the top-seeded melt growth (TSMG) processed Y1.5 sample was $3.2{\times}10^4\;A/cm^2$. The magnetic flux density (H) at 77 K of the TSMG-processed Y123 and Y1.5 sample showed the 0.53 kG and 2.45 kG, respectively, which are 15% and 71% of the applied magnetic field of 3.5 kG. The high H value of the TSMG-processed Y1.5 sample is attributed to the formation of the larger superconducting grain with fine Y211 dispersion.

• Composites Research
• /
• v.30 no.2
• /
• pp.138-144
• /
• 2017

Damage sensing of polymer composite films consisting of poly(dicyclopentadiene) p-DCPD and carbon nanotube (CNT) was studied experimentally. Only up to 1st ring-opening polymerization occurred with the addition of CNT, which made the modified film electrically conductive, while interfering with polymerization. The interfacial adhesion of composite films with varying CNT concentration was evaluated by measuring the wettability using the static contact angle method. 0.5 wt% CNT/p-DCPD was determined to be the optimal condition via electrical dispersion method and tensile test. Dynamic fatigue test was conducted to evaluate the durability of the films by measuring the change in electrical resistance. For the initial three cycles, the change in electrical resistance pattern was similar to the tensile stress-strain curve. The CNT/p-DCPD film was attached to an epoxy matrix to demonstrate its utilization as a sensor for fracture behavior. At the onset of epoxy fracture, electrical resistance showed a drastic increase, which indicated adhesive fracture between sensor and matrix. It leads to prediction of crack and fracture of matrix.

• Resources Recycling
• /
• v.20 no.3
• /
• pp.68-76
• /
• 2011

For the separation of aluminum and iron from platinum mixtures, extraction resins were synthesized and separation efficiencies were compared with those by commercial one, $P_{204}$. During synthesis, the suspension polymerization method was adopted with D2EHPA as an extractant. Also, benzoyl peroxide as a starter was divided into 3parts and injected for the uniform size and dispersion of resin particles. Comparison tests resulted in 100% separation of Fe and Pt for both synthetic and $P_{204}$ resins. In case of Al and Pt, synthetic and $P_{204}$ resin gave extraction efficiencies of 99.9% and 98.9%, respectively. Difference in extractant contents of synthetic resin(61.8%) and $P_{204}$(60%) was considered to give differences in separation efficiencies of aluminum and iron elements. For both resins, separation efficiencies of Al and Fe increased up to $55^{\circ}C$. According to FT-IR analyses of both resins, specific peaks of D2EHPA and crosslinked polystyrene were identified at the wavenumber of $1000cm^{-1}$ and $2900cm^{-1}$ respectively.

• Journal of the Korean earth science society
• /
• v.27 no.5
• /
• pp.557-568
• /
• 2006

We present CCD UBVI photometry for more than 10,000 stars in $20'.5{\times}20'.5$ field of the halo globular cluster M30. From a color-magnitude diagram, main sequence turnoff was obtained when $V_{TO},\;(B-V)_{TO},\;and\;(V-I)_{TO}\;are\;8.63{\pm}0.05,\;0.44{\pm}0.05\;and\;0.63{\pm}0.05$, respectively. From a (U-B)-(B-V) diagram, reddening parameter, E(B-V) equals $0.05{\pm}0.01$ and a UV color excess ${\delta}(U-B)\;is\;0.27{\pm}0.01$. The abundance is derived, where [Fe/H] equals $-2.05{\pm}0.09$ according to the photometric method and spectroscopic data. The observed luminosity function of M30 shows an excess in the number of red giants relative to the number of turnoff stars, when comparing with the predictions of canonical models. Using the Hipparcos parallaxes for subdwarfs, we estimate distance modulus, $(m-M)_o\;as\;14.75{\pm}0.12$. Using the R and R' method, we find helium abundances, Y(R) as $0.23{\pm}0.02$, Y(R') as $0.29{\pm}0.02$, respectively. Finally, the cluster' sage dispersion was deduced from 10.71 Gyr to 17 Gyr.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.5
• /
• pp.545-566
• /
• 1999

The use of pure titanium and titanium alloys have been increased recently in fixed, removable prosthodontics and implant fields as a framework. But when they were used for superstructures of implant or metal framework of removable prosthesis, welding is necessary to reconnect the fracture site to control the casting distortions. To overcome the difficulties in soldering the titanium due to high oxidation property, much effort have been devoted. In this study, some of mechanical properties were compared between pure titanium and Ti-6Al-4V alloy by using after welding, electron beam welding technique and tungsten arc welding. Mechanical properties such as tensile strength, yield strength, elongation and microhardness were measured. And, in order to compare the effect of welding site and surrounding metal tissue according to the welding condition, SEM photographs were taken and element distribution was observed by Wave Dispersion Spectroscopy. Through analyses of the data, following results were obtained; 1. In items such as tensile strength, yield strength and elongation according to the welding techniques of pure titanium, only tungsten arc welded group showed significant lower value than other groups(P<0.05). 2. In items such as tensile strength and yield strength according to the welding techniques of Ti-6Al-4V alloy, control group and tungsten arc welded group showed significant difference among all the groups(P<0.05). 3. Ti-6Al-4V alloy exhibited significantly greater elongation than control group when the laser welding method and electron beam welding method were used, and elongation showed increasing tendency. 4. Pure titanium specimens exhibited increasing tendency of microhardness regardless of the weld-ing technique applied, and especially tungsten arc welded group demonstrated a great increase of microhardness than parent metal. 5. There was no hardness change in laser welded group and electron beam welded group of Ti-6Al-4V alloy, but in tungsten arc welded group, hardness changed greatly from parent metal to weld seam. 6. Through the metallographic examination and scanning electron microscopy, laser welding caused central fusion and recristallizations were formed and tungsten arc welding caused localized fusion to 0.3-0.7mm from the surface.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.129-136
• /
• 2011

Simulated Moving Bed(SMB) process consists of multiple chromatographic columns, which are usually partitioned into four zones. Such a process characteristic allows a continuous binary separations those are impracticable in conventional batch chromatographic processes. Compared with batch chromatography, SMB has advantages of continuity, high purity and productivity. Various researches have been reported for the integration of reaction and recovery during process operation on the purpose of economics and effectiveness. Simulated Moving Bed Reactor(SMBR) is introduced to combine SMB as a continuous separation process and reactor. Several cases of SMBR have been reported for diverse reactions with catalytic, enzymatic and chemical reaction on ion exchange resin as main streams. With an early type of fixed bed using catalyst, SMBR has been developed as SMB using fluidized enzyme, SMB with immobilized enzyme and SMB with discrete reaction region. For simple modeling and optimization of SMBR, a method considering convection only is possible. A complex method considering axial dispersion and mass transfer resistance is needed to explain the real behavior of solutes in SMBR. By combining reaction and separation, SMBR has benefits of lower installation cost by minimizing equipment use, higher purity and yield by avoiding the equilibrium restriction in case of reversible reaction.

• Resources Recycling
• /
• v.21 no.3
• /
• pp.15-20
• /
• 2012

In this paper, we carried out separation of membrane and leaching of Pt and Ru using hydrochloric acid from MEA(membrane-electrode assembly) of fuel cell. In this method, these were separated from MEA of fuel cell using the distilled water, 10 vol.% butanol solution and 15 vol.% cationic surfactant(Koremul-LN-7) by dipping method without the dispersion of catalyst particles. And the leaching of Pt and Ru containing in the separated carbon paper catalysts has been studied by hydrochloric acid using $HNO_3$ or $H_2O_2$ as a oxidant. The leaching ratio of Pt and Ru were higher when $H_2O_2$ was used as a oxidant and the optimum conditions were obtained in 8M HCl, the amount of $H_2O_2$ 5M and 6 hours of leaching time at $90^{\circ}C$. In this condition, extraction of Pt and Ru were 98% and 71.5%, respectively.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.2
• /
• pp.181-188
• /
• 2009

Pt catalyst was adsorbed on Carbon nanofiber (CNF) by modified polyol method after acid treatment of the carbon support with $HNO_3$ and $H_{2}SO_{4}$. As the time for acid treatment increases, more oxygen functional groups on carbon surface were produced which improve the loading amount and dispersion of Pt catalyst on carbon supports. In order to inspect the effect of CNF acid treatment time on electrochemical corrosion, constant potential of 1.4 V was applied to a single cell for 30 min and the amount of $CO_2$ emitted was monitored with on-line mass spectrometry. According to the results of our experiment, more $CO_2$ was produced with Pt/ oxidized-CNF catalyst in compared to that with unoxidized-CNF. Increasing acid treatment time also induces the more $CO_2$ emission. Besides, performance degradation after corrosion test expanded with severer carbon corrosion. From the observed results, it can be concluded that the acid treatment of CNF is beneficial to catalyst loading, but it also is a significant factor declining the fuel cell durability by accelerating electrochemical oxidation of carbon support.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.45-55
• /
• 1996

Although the Dongjin Au-Ag-Cu mine had been abandoned since about forty years ago, the results of this study on the dispersion patterns and contamination level of heavy metals in the hydrologic system flowing via the waste rump show that the environmental impacts from the mine wastes are still significant. The stream water in the vicinity of the waste rump is severely acidified (pH 3.8 to 4.4) and highly enriched in various dissolved heavy metals. The heavy metal contents of the stream water and stream sediments are systematically attenuated with increasing distance from the mine area. However, it is worth to note that continuous attenuation of heavy metal contents in both media were reenriched in downstream area more than 800 m apart from the mine because it can be acted as a secondary source of heavy metal pollution. The heavy metals, especially Cd, Cu and Zn of polluted downstream sediments mainly occur in Fe-Mn oxides and organic materials, which indicates that these elements are the main pollutants from the waste rump of the Dongjin mine. The heavy metal contents of crops, such as sesame, perilla, red Pepper and brown rice, collected from the polluted farm land in the downstream area are lower than those of land plants from stream sides, but significantly higher in Cd, Cr, Cu and Zn than those from the unpolluted farm land. Especially, almost all of the crops in polluted farm land have been severly contaminated by Cd (>0.4 ppm). On the other hand, the heavy metal contents of the crops collected from refreshed farm land by means of a soil addition method shows significantly lowered level comparing with those of polluted area, which indicates that a soil addition method was effective for the refreshment of polluted farm land by toxic metallic pollutants. Wormwoods from this area showed very high contents in a11 the heavy metals even in unpolluted area (Cd > 1 ppm, Cr > 1 ppm, Cu > 11 ppm, Pb> 4 ppm, Zn > 55 ppm), indicating that a special caution must be payed when one takes ingest them.