• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.55.2-55.2
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.4
• /
• pp.320-329
• /
• 2007

Electrokinesis and dielectrophoresis are important transport phenomena produced by external electric field applied to a microchannel containing a conductive fluid. We developed a CFD code to predict electrokinetic and dielectrophoretic flows in a microchannel with a uniform circular post array. Using the code, we calculated particle velocities driven by electrokinesis and dielectrophoresis, and conducted Monte Carlo simulations to visualize the particle motions. The code was validated by comparing the results with those from previous studies in literature. At a low electric field, electrokinesis and diffusion is the dominant transport mechanism. At a moderate electric field, dielectrophoresis is balanced with electrokinesis and diffusion, resulting in flowing filaments of particles in the microchannels. However, dielectrophoresis overwhelms the flow at a high electric field and traps particles locally. These results provide useful insight for optimizing design parameters of a microfluidic chip for biochemical analysis, especially for development of on-chip sample pretreatment techniques using electrokinetic and dielectrophoretic effects.

• Korean Journal of Materials Research
• /
• v.17 no.3
• /
• pp.167-172
• /
• 2007

The separation of the small colloidal particles from the mixture of two different sized particles using AC dielectrophoresis phenomenon was studied. The spherical mono-dispersed polystyrene particles dispersed in pure water were put into a perfusion chamber on a substrate, and AC electric fold was applied to the glass substrate with Au electrodes in 4 mm distance. The AC frequency was fixed at 1 kHz and the intensity of the field was varied from 25 V/cm to 160 V/cm. After applying the AC field, the degree of the chain formation that resulted from the particle movements by dielectrophoresis was observed by optical microscope. The mixture of the $1\;{\mu}m\;and\;5\;{\mu}m$ sized polystyrene particles at 0.5 vol% concentrations for each size was set in the dielectrophoresis conditions of 1 kHz and 100 V/cm. At this condition large $5\;{\mu}m$ sized polystyrene particles formed chains, on the contrary the $1\;{\mu}m$ sized polystyrene particles formed no chains. After water flowing for 20 min, it was found that small particles that were floating in the chamber had been removed by the water flowing.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.2
• /
• pp.56-60
• /
• 2012

Graphene oxide, which is exfoliated by oxidant from graphite, is the material for solving the problem of mass production and positioning. We made graphene oxide based devices by dielectrophoresis, studied and controlled factors which can affect the characteristic of graphene oxide channel. Graphene oxide channel assembled by dielectrophoresis can be constructed differently by various frequency options. We confirmed the change of gate characteristics and I-V characteristics in the range from 80K to 300K temperature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.2 s.245
• /
• pp.179-186
• /
• 2006

Dielectrophoresis has received considerable attention for separating nanotubes according to electronic types. Here we examine the effects of surface conductivity of semiconducting single-walled carbon nanotubes (SWNT), induced by ionic surfactants, on the sign of dielectrophoretic force. The crossover frequency of semiconducting SWNT increases rapidly as the conductivity ratio between the particle and medium increases, leading to an incomplete separation of ionic surfactant suspended SWNT at an electric field frequency of 10 MHz. The surface charge of SWNT is neutralized by an equimolar mixture of anionic surfactant sodium dodecyl sulfate (SDS) and cationic surfactant cetyltrimenthylammonium bromide (CTAB), resulting in negative dielectrophoresis of semiconducting species at 10 MHz. A comparative Raman spectroscopy study shows a nearly complete separation of metallic SWNT.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.54.2-54.2
• /
• 2005

• Journal of Sensor Science and Technology
• /
• v.18 no.2
• /
• pp.139-146
• /
• 2009

A Multilayered microelectrode design is presented for large area travelling wave dielectrophoresis (TwDEP) separators. Most of typical TwDEP chip has been arrayed with 1000 electrodes in $20{\times}20\;mm^2$. However, there is a limitation of the device area that is critical in throughput, because when the area of TwDEP becomes larger, the resistance of microelectrodes for bus bar is also increased. In this paper, we successfully developed a novel TwDEP chip with extremely large area ($31{\times}25\;mm^2$) by a unique multilayered bus bar design. According to the resistance simulation of our microelectrodes, it is possible to realize a TwDEP chip with an infinite longitudinal length. We demonstrated the feasibility of our suggestion with latex microbeads and showed the potential of extremely high throughput separation with TwDEP technique.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.1
• /
• pp.105-108
• /
• 2011

Newly-developed fabrication of a p-n heterojunction diode constructed with a p-Si nanowire (NW) and an n-ZnO nanoparticle (NP) thin-film by the dielectrophoresis (DEP) technique is demonstrated in this study. With the bias of 20 Vp-p at the input frequency of 1 MHz, the most efficient assembly of the n-ZnO NPs is shown for the fabrication of the p-n heterojunction diode with a p-Si NW. The p-n heterojunction diode fabricated in this study represents current rectifying characteristics with the turn on voltage of 1.1 V. The diode can be applied to the fabrication of optoelectrical devices such as photodetectors, light-emitting diodes (LEDs), or solar cells based on the high conductivity of the NW and the high surface to volume ratio of the NP thin film.

• Korean Journal of Materials Research
• /
• v.23 no.1
• /
• pp.13-17
• /
• 2013

The alignments of polystyrene particles of $1{\mu}m$ and $5{\mu}m$ sizes in an aqueous colloidal system were observed by varying the electric field strength, the frequency and the water flow. Spherical mono-dispersed polystyrene particles dispersed in pure water were put into a perfusion chamber; an AC electric field was applied to the Au/Cr electrodes with a 4 mm gap on the glass substrate. The mixture of the $1{\mu}m$ and $5{\mu}m$ sized polystyrene particles at 0.5 vol% concentrations for each size was set in the dielectrophoresis conditions of 1 kHz and 150 V/cm. Large particles of $5{\mu}m$ size were aligned to form chains as the result of the dielectrophoresis force interaction. On the contrary, small particles of $1{\mu}m$ size did not form chains because the dielectrophoresis force was not sufficiently large. When the electric field increased to 250 V/cm, small particles were able to form chains. After the chains were formed from both large and small particles, they began to coalescence as time passed. Owing to the electroosmotic flow of water, wave patterns along the perpendicular direction of the applied electric field appeared at the conditions of 200 Hz and 50 V/cm, when the dielectrophoresis force was small. This wave pattern also appeared for small particles at 1 kHz and 150 V/cm conditions due to the flow of solvent when water was forced to circulate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1535-1538
• /
• 2005

We present a mass productive and reproducible assembly technique of a single bundle of single-walled carbon nanotubes (sb-SWNTs) using dielectrophoresis (DEP). Gold electrodes with 10 gaps made via microlithography were used to align the carbon nanotubes (CNTs). The magnitude and type of applied electric field were investigated to verify their effects on CNT assembly. The optimum assembling conditions in which sb-SWNTs could be positioned at a desired site were experimentally identified, and the characteristics of the assembled sb-SWNTs were evaluated from AFM, Raman spectroscopy, and I-V curve. This assembly method has potential for applications such as gas sensors or electronic devices.