• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.1-4
• /
• 1994

In this study. the microwave dielectric properties, such at dielectric constant(${\varepsilon}_{\gamma}$), unloaded quality factor multiplied with resonant frequency($Q_{u}$.f), and temperature coefficient of resonant frequency(${\tau}_{f}$), were investigated for the low-temperature sintered (Pb, Ca)$ZrO_3$ with $V_2O_{5}$ additives as well as structural properties. As a result, (Pb,Ca)ZrO$_3$ with 0.2 wt% $V_2O_{5}$ additive, sintered at $1200^{\circ}C$, showed good properties like ${\varepsilon}_{\gamma}$ 109, $Q_{u}$.f 2736 GHz, and ${\tau}_{f}$ -2.94 ppm/$^{\circ}C$. Especially ${\tau}_{f}$ was much better than ($Pb_{0.63}Ca_{0.37}$)$ZrO_3$ of which ${\tau}_{f}$ was known to be + 13.4 ppm/$^{\circ}C$, so it seems to be applicated in micorowave device components.

• Journal of Sensor Science and Technology
• /
• v.12 no.5
• /
• pp.199-204
• /
• 2003

This paper describes on the fabrication and characteristics of a ceramic thin-film pressure sensor based on Ta-N strain-gauges for harsh environment applications. The Ta-N thin-film strain-gauges are sputter-deposited onto a micromachined Si diaphragms with buried cavity for overpressure protectors. The proposed device takes advantages of the good mechanical properties of single-crystalline Si as diaphragms fabricated by SDB and electrochemical etch-stop technology, and in order to extend the operating temperature range, it incorporates relatively the high resistance, stability and gauge factor of Ta-N thin-films. The fabricated pressure sensor presents a low temperature coefficient of resistance, high-sensitivity, low non-linearity and excellent temperature stability. The sensitivity is $1.097-1.21\;mV/V{\codt}kgf/cm^2$ in the temperature range of $25-200^{\circ}C$ and the maximum non-linearity is 0.43%FS.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.2
• /
• pp.56-67
• /
• 2006

The reliability and failure mode effect analysis are effective means to achieve efficient and cost-reduction design for satellite development. The failure rate of COTS (Commercial-Off-The-Shelf) parts required for reliability analysis is not usually provided from the manufacturer. Space environment factors based on empirical data obtained from MIL-HDBK-217F can be applicable to the reliability calculation. As a radiation environment factor, the occurrence rate of SEL (Single Event Latch-up) is additionally incorporated for the failure rate prediction. In this paper, the statistical reliability analysis method for low-cost small satellite using COTS parts is suggested. This statistical reliability analysis was applied to HAUSAT-2 small satellite whose electronic boxes are consisted of many COTS parts to calculate the system reliability at the end of design mission life.

• Proceedings of the KIEE Conference
• /
• 2007.11a
• /
• pp.148-149
• /
• 2007

We present the design and fabrication prcoess of a two-axis tilting micromirror device driven by the electrostatic vertical comb actuator. A high aspect-ratio comb actuator is fabricated by multiple DRIE process in order to achieve large scan angle. The proposed fabrication process enables a mirror to be fabricated on the wafer-scale. By bonding a double-side polished (DSP) wafer and a silicon-on-insulator (SOI) wafer together, all actuators on the wafer are completely hidden under the reflectors. Nickel lines are embedded on a Pyrex wafer for the electrical access to numerous electrodes of mirrors. An anodic bonding step is implemented to contact electrical lines with ail electrodes on the wafer at a time. The mechanical angle of a fabricated mirror has been measured to be 1.9 degree and 1.6 degree, respectively, in the two orthogonal axes under driving voltages of 100 V. Also, a $8{\times}8$ array of micromirrors with high fill-factor of 70 % is fabricated by the same fabrication process.

• IE interfaces
• /
• v.19 no.4
• /
• pp.306-315
• /
• 2006

In this paper we analyze whether we can use the mobile phone having been highly distributed into young generation as a device for the u-learning in Korean public education. For this purpose we deal with the technical maturity in three axes. Firstly, we examine the authoring nature of mobile internet-based contents such as both text and motion picture for the contents developers in the public education. As a research result the authoring of text has almost no difficulty, but that of the motion picture shows some problems. Secondly, we deal with whether u-learners can easily get and use u-contents on both mobile phone and PC respectively. After analysing this factor, we found that the downloading of motion picture contents into mobile phone is very limited. Therfore we talk about the usability and problem of various PC Sync tools and propose their standardization. Finally, the needs of the introduction of the ubiquitous SCORM which could enable to reuse u-contents among different Korean telco’s mobile phones are discussed. Here we describe some functionality of both ubiquitous SCORM and u-LMS. Our study looks like almost the first work examining the technological maturity for the introduction of u-learning with mobile phone in Korean public education and it could be used as a reference for the study of any other wireless telecommunication-based u-learning other than mobile telecommunication.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.12
• /
• pp.169-175
• /
• 2009

Microbial fuel cell (MFC) is a device to produce a electricity from the oxidation of organic materials using microorganism. Recently many researchers have been studying MFC which is focused as regeneration energy source. Previews studies have focused every each factor that influence the production of electric power. However they didn't study a lot about the correlation among the factors. In order to improve the MFC, we analysed the factors which influencing the generation of electric power of MFC. Also, we made a new compartment to verify the correlations among the factors efficiently. Based on the result obtained from the experiments in the laboratory, we analysed the factors and we suggested a new concept of waste water treatment system to produce electrical energy during the treatment of waste water.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1575-1580
• /
• 2011

A key factor in the study of hybrid vehicle is to enhance the usability of energy. The paper introduces the monitor and controlling technology of hybrid vehicle that can process the relevant information considering the structure of power system and driving strategies simultaneously, and can monitor its results. This technology, so called HEV algorithm analysis, has been applied to PRIUS THS made by Toyota Co. LTD. This model is adapted to parallel hybrid type. It has a somewhat comlex structure, but has several merits. It's energy loss is lower when conversing. and also it is easily applied to the conventional vehicle having a gasoline engine without any overall changing of its structure, and so on. This monitor and controlling technology is very useful to study on the various driving strategies of hybrid vehicle for maximizing the usability between engine and electric motor.

• Journal of the Korean Institute of Gas
• /
• v.21 no.1
• /
• pp.1-5
• /
• 2017

In the event of toxic gas accidents, soil deposition is a main factor which has an effect on extent of the damage. In this study, it presents the influence of soil deposition properties according to the change of soil depth and the organic matter contents in soil. In this experimentation, the soil deposition device developed in Air Force Research Laboratory in USA is recreated. The tested samples of mixing soil have each value of the organic matter contents. After a variety of synthetic soil were exposed to constant Cl2 concentration, the chlorinity is measured using an anion exchange chromatography(ICS-1100) to quantify the mount of deposition. As the results, the increase of soil depth causes an decreased soil deposition and the increase of exposure time causes an increased soil deposition in surface. Also, the increase of soil deposition mainly depended on the organic matter contents in surface.

• Tribology and Lubricants
• /
• v.31 no.2
• /
• pp.35-41
• /
• 2015

A water-pump located in the cooling area of a car circulates cooling water. A particular bearing element, known as a water-pump bearing, installed in the rotating part carries the entire load. The failure of this water-pump bearing has a direct impact on the failure of the automobile engine, and so securing its reliability is crucial. Several researchers have examined the design principles of the water-pump bearing, but there are no reports on the life characteristic of the bearing yet. Herein, we report the construction of test equipment to reproduce the spalling of the roller contact, which is the main failure mode of the chosen water-pump bearing. We chose the radial load as an accelerated stress factor and validated the failure mode by monitoring the surface defects. We conducted the accelerated life test after determining the accelerated stress level through a combination of finite element analysis and a preliminary test. In the life tests, we used an accelerometer to perform failure diagnosis. In the last stage of this study, we present a statistical reliability analysis. Thus, we fully estimated the shape parameter of the water-pump bearing, accelerating level on the load , and the lifetime (MTTF and B₁₀ life) under real use conditions, and finally proposed an interval estimation value considering the uncertainty of the estimated value.

• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.508-512
• /
• 2012

ZnO thin films were grown on a sapphire substrate by RF magnetron sputtering. The characteristics of the thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL), and Hall effect. The substrate temperature and growth time were kept constant at $200^{\circ}C$ at 30 minutes, respectively. The RF power was varied within the range of 200 to 500 W. ZnO thin films on sapphire substrate were grown with a preferred C-axis orientation along the (0002) plan; X-ray diffraction peak shifted to low angles and PL emission peak was red-shifted with increasing RF power. In addition, the electrical characteristics of the carrier density and mobility decreased and the resistivity increased. In the electrical and optical properties of ZnO thin films under variation of RF power, the crystallinity improved and the roughness increased with increasing RF power due to decreased oxygen vacancies and the presence of excess zinc above the optimal range of RF power. Consequently, the crystallinity of the ZnO thin films grown on sapphire substrate was improved with RF sputtering power; however, excess Zn resulted because of the structural, electrical, and optical properties of the ZnO thin films. Thus, excess RF power will act as a factor that degrades the device characteristics.