• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.3
• /
• pp.292-301
• /
• 2014

This paper describes development of distributed type independent electro-hydraulic ballast valve remote control system with diagnostic function based on fuzzy inference using redundant Modbus communication and ethernet Modbus TCP/IP. Diagnostic function estimate degradation of system components and diagnose system faults, which results in shortage of fault maintenance time and improvement of system safety. Slave devices which control each valve and master device which command, monitor and diagnose slave system are developed. Slave devices are connected to master device with redundant Modbus networks and master device is connected to ship's integrated control system with Modbus TCP/IP. Also this paper describes development of simulator to test and confirm whether developed system can be integrated with ship's integrated control and monitoring system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.61-63
• /
• 2005

Pentacene based OTFT on PC and PES plastic substrates have been fabricated in a scale of 5 inches. We could get a small OTFT device enough to be applicable for AMOLED by acquiring the at least misalignment margin through a contact aligner. And also we could find out the degradation of device parameter through the integration processes and improve the properties by using a buffer layer as an etch stopper in an active patterning. Through these, the mobility of device is more than about $0.2cm^2/Vs$ and $I_{on}/I_{off}$ is higher than $10^5$.

• Journal of Information Display
• /
• v.8 no.2
• /
• pp.10-14
• /
• 2007

A blazed $GxL^{TM}$ device is described as having high optical efficiency (> 70% for RGB lasers), and high contrast ratio (> 10,000:1), and that is highly reliable when used in a large-area laser projection system. It has a robust design and precise stress control technology to maintain a uniform shape (bow and tilt) of more than 6,000 ribbons, a $0.25-{\mu}m$ CMOS compatible fabrication processing and planarization techniques to reduce fluctuation of the ribbons, and a reliable Al-Cu reflective film that provided protection against a high-power laser. No degradation in characteristics of the GxL device is observed after operating a 5,000- lumen projector for 2,000 hours and conducting 2,000 temperature cycling tests at $-20^{\circ}C$ and $+80^{\circ}C$. At the 2005 World Exposition in Aichi, Japan the world's largest laser projection screen with a size of 2005 inches (10 m ${\times}$ 50 m) and 6 million pixels (1,080 ${\times}$ 5,760) was demonstrated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.1029-1032
• /
• 2008

Nowadays, the necessity of the NDT technique for concrete structure has been increased due to maintenance of infra-structure. With this reason, NDT detecting technique has been considered as a effective maintenance method to prevent the rapid degradation of the infra-structure. In this study, to investigate the internal defect of concrete structure, ultrasonic detection device and radar equipment was applied then tested in laboratory and field. In the result of the experimental test, the internal cavity and steel arrangement can be detected and it was possible to adopt the ultrasonic detection method to the maintenance of concrete structure. And an algorithm for performing the maintenance procedure of concrete structure applying ultrasonic detection device and radar equipment was developed and suggested in this study.

• Journal of IKEEE
• /
• v.16 no.4
• /
• pp.283-289
• /
• 2012

In this paper, We proposed Separate Gate Technique(SGT) to improve the switching characteristics of Trench power MOSFET. Low gate-to-drain 전하 (Miller 전하 : Qgd) has to be achieved to improve the switching characteristics of Trench power MOSFET. A thin poly-silicon deposition is processed to form side wall which is used as gate and thus, it has thinner gate compared to the gate of conventional Trench MOSFET. The reduction of the overlapped area between the gate and the drain decreases the overlapped charge, and the performance of the proposed device is compared to the conventional Trench MOSFET using Silvaco T-CAD. Ciss(input capacitance : Cgs+Cgd), Coss(output capacitance : Cgd+Cds) and Crss(reverse recovery capacitance : Cgd) are reduced to 14.3%, 23% and 30% respectively. To confirm the reduction effect of capacitance, the characteristics of inverter circuit is comprised. Consequently, the reverse recovery time is reduced by 28%. The proposed device can be fabricated with convetional processes without any electrical property degradation compare to conventional device.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.3
• /
• pp.577-584
• /
• 2017

Long Term Evolution device-to-device (LTE D2D) is a key technology to mitigate data traffic load in a cellular system. It facilitates direct data exchange between neighboring users, which is preceded by D2D discovery. Each device advertises its presence to neighboring devices by broadcasting its discovery message. In this paper, we develop a mathematical analysis to assess the probability that discovery messages are successfully transmitted at the D2D discovery stage. We make use of stochastic geometry for modeling spatial statistics of nodes in a two dimensional space. It reflects signal to noise plus interference ratio (SINR) degradation due to resource collision and in-band emission, which leads to the discovery message reception probability being modeled as a function of the distance between the transmitter and the receiver. Numerical results verify that the newly developed analysis accurately estimates discovery message reception probabilities of nodes at the D2D discovery stage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.156-162
• /
• 2015

This paper has analyzed how conduction path and electron concentration for the device parameters such as oxide thickness, channel doping, and top and bottom gate voltage influence on subthreshold swing of asymmetric double gate MOSFET. Compared with symmetric and asymmetric double gate MOSFET, asymmetric double gate MOSFET has the advantage that the factors to be able to control the short channel effects increase since top and bottom gate oxide thickness and voltages can be set differently. Therefore the conduction path and electron concentration for top and bottom gate oxide thickness and voltages are investigated, and it is found the optimum conditions that the degradation of subthreshold swing, severe short channel effects, can reduce. To obtain the analytical subthreshold swing, the analytical potential distribution is derived from Possion's equation. As a result, conduction path and electron concentration are greatly changed for device parameters, and subthreshold swing is influenced by conduction path and electron concentration of top and bottom.

• Journal of the Optical Society of Korea
• /
• v.16 no.4
• /
• pp.349-353
• /
• 2012

Uniform spreading of injection current in light-emitting diodes (LEDs) is one of the crucial requirements for better device performances. It is reported that non-uniform current spreading leads to low output power, high current crowding, heating, and reliability degradation of the LED device. This paper reports on the effects of different surface and electrode geometries in the LEDs. To increase the output power of LEDs and reduce the series resistance, a rectangular-type LED (RT-LED) with a centered island cathode has been fabricated and investigated by comparison with a conventional LED (CV-LED). The performances of RT-LEDs were prominently enhanced via uniform current spreading and low current crowding. Performances in terms of increased output power and lower forward voltage of simulated RT-LEDs are much superior to those of CV-LEDs. Based on these results, we investigated the correlation between device geometries and optical characteristics through the fabricated CV and RT-LEDs. The measured output power and forward voltage of the RT-LEDs at 100 mA are 64.7% higher and 8% smaller compared with those of the CV-LEDs.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.83-87
• /
• 2023

In the field of electronics and semiconductor technology, innovative semiconductor material research to replace Si is actively ongoing. However, while research on alternative materials is underway, there is a significant lack of studies regarding the relationship between 2D materials used as channels in transistors, especially parasitic resistance, and RF (radio frequency) applications. This study systematically analyzes the impact on electrical performance with a focus on various transistor structures to address this gap. The research results confirm that access resistance and contact resistance act as major factors contributing to the degradation of semiconductor device performance, particularly when highly scaled down. As the demand for high-frequency RF components continues to grow, establishing guidelines for optimizing component structures and elements to achieve desired RF performance is crucial. This study aims to contribute to this goal by providing structural guidelines that can aid in the design and development of next-generation RF transistors using 2D materials as channels.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.6
• /
• pp.424-432
• /
• 2023

This study deals with the design of a safety device around a leisure boat propeller. The safety device is to be designed to minimize performance degradation attached to propulsors in coastal waters. These devices, important for preventing propeller accidents, negatively gives influence boat performance, especially at higher speeds. In order to minimize the negative effect, the accelerating ducts, normally used in ESDs (Energy Saving Devices) have been chosen as a safety device. The present study aims to design an optimal duct (minimizing negative effect) through the parametric study. Based on the Marine 19A nozzle, the nozzle's thickness and angle were varied to obtain the optimum parameter in the preliminary design by the computational fluid dynamics program Star-CCM+ Ver. 15.02. In the detailed design, a NACA 4-digit Airfoil shape resembling the Marine 19A by modification at the trailing edge was chosen and the optimum shape was chosen according to variation of camber, thickness, and incidence angle for optimization. The optimally designed duct shows a speed decrease of about 10% in the sea trial result, which is much smaller than the normal speed decrease of at least 30%. The present designing method can give wide applications to the leisure boat because the wake is almost the same due to using the outboard propulsor.