• The Journal of Engineering Geology
• /
• v.16 no.3 s.49
• /
• pp.245-254
• /
• 2006

Using a natural gradient tracer test, the characteristics of hydrodynamic dispersion according to each depth of a fractured rock were studied, and the effective porosity and longitudinal dispersivity of the fractured rock were estimated. The difference of vertical hydrodynamic dispersion was identified by concentration breakthrough curves linear regression analyses of bromide concentrations according to depths versus time, and hydraulic fracture characteristics at two intervals of the monitoring well. Higher concentration and faster arrival time at GL- 18 m depth (RQD 13%, average joint spacing 2 cm, TCR 100%) than at GL- 25 m depth (RQD 41%, average joint spacing 7 cm, TCR 100%) resulted from shorter distance and more fractures. Tracer was transported through the 1 st fractures until the arrival of its peak concentration and through the 2nd fractures or matrix diffusion after the arrival of its peak concentration. The increase/decrease slopes of bromide concentration versus time were 3.46/-1.57 at GL-18 m depth and 3.l9/-0.47 at GL- 25 m depth of the monitoring well. So the faster bromide transport was confirmed at GL- 18 m depth with more fractures. The concentration increment of bromide was fitted by a Gaussian function and the concentration decrement of bromide was fitted by an exponential function. Effective porosity and longitudinal dispersivity estimated by CATTI code were 10.50% and 0.85 m, respectively.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.184-191
• /
• 2023

With increasing corrosion in RC (Reinforced Concrete) structures, cracks occurred due to corrosion products and bearing load resistance decreased. In this study, corrosion was induced through an accelerated corrosion test (ICM: Impressed Current Method) with 140 hours of duration, and changes in USV (Ultra-Sonic Velocity), flexural failure load, and corrosion weight were evaluated before and after corrosion test. Three levels of cover depth (20 mm, 30 mm, and 40 mm) were considered, and the initial cracking period increased and the rust around steel decreased with increasing cover depth. In addition, the USV linearly decreased with decreasing cover depth and increasing amount of corrosion. In the flexural loading test, the bending capacity decreased by more than 10% due to corrosion, but a clear correlation could not be obtained since the corrosion ratio was small, so that the effect of slip was greater than that of reduced cross-sectional area of steel due to corrosion. As cover depth increased, the produced corrosion amount and USV changed with a clear linear relationship, and the cracking period due to corrosion could be estimated by the gradient of the measured corrosion current.

• Corrosion Science and Technology
• /
• v.6 no.4
• /
• pp.186-192
• /
• 2007

Carbonation is one of the most important factors causing the corrosion of reinforcement concrete. Nevertheless, experimental studies on the concrete carbonation have not been carried out sufficiently because of the slow process of carbonation process. Therefore, this study adopts an experimental system exploiting a vacuum instrument that has been recently developed to accelerate carbonation instead of existing experimental system to conduct rapid carbonation tests on Portland cement and fly-ash cement concretes. Test results revealed that, compared to water-cement ratio of 40%, the carbonation depth increases from 103% to 138% for an increase of water-cement ratio from 45% to 60%. These results are larger than the carbonation depths obtained by mathematical model, and such difference is increasing with larger water-cement ratios. The results also indicated that larger fly-ash contents lead to sharp increase of the carbonation depth, which is in agreement with previous experimental researches. The adoption of the new accelerated carbonation test system enabled to shorten effectively the time required to produce experimental data compared to the existing carbonation test method. The experimental data obtained in this study together with ongoing acquisition of data using the new carbonation test method are expected to contribute in the understanding of the carbonation process of concrete structures in Korea.

• International Journal of Highway Engineering
• /
• v.16 no.2
• /
• pp.35-41
• /
• 2014

PURPOSES : Surface treatment is a favorable method in the pavement preventive maintenance. This study (Part I) aimed to develop the low viscosity filling material for waterproof characteristics and high penetrable and weather resistance, and a series of companion study (Part II) presents the coating characteristics and performance analysis using field and lab tests. METHODS : Hydrophobic characteristics of the advanced surface treatment material are observed and measured the filling depth and the permeability for sand and asphalt pavement specimen using the water absorption test and permeability test, X-RAY CT test. Color difference for the weather resistance using ultraviolet ray accelerated weathering test is compared with asphalt pavement specimens. RESULTS : The developed material shows the decreased water absorption and increased impermeable effect because of the hydrophobic characteristics. It is found that the filling depth is about 6mm and weather resistance is better than asphalt pavement specimen. CONCLUSIONS : The advanced hydrophobic - low viscosity filling treatment material is developed in this study (Part I) to improve the waterproof characteristics and high filling capacity and weather resistance for the pavement preventive maintenance.

• Journal of Periodontal and Implant Science
• /
• v.29 no.1
• /
• pp.95-102
• /
• 1999

The purpose of this study was to observe histopathologically the influence of advanced periodontitis on pulp tissue, and to conclude the correlation between the results with clinical manifestations. The samples were teeth with over 7mm pocket depth and over 50% radiographic bone loss. These were diagnosed to have very poor prognosis and thus planned to be extracted. Those with any of following conditions were excluded from the samples, loss of vitality, periapical pathology, restoration or prosthesis, dental caries, and attrition or abrasion. It was because these conditions could affect pulp without any correlation with periodontal disease. For the experiment, 17 teeth from 11 patients were selected. Average age of patient was 47. Each tooth was examined for following categoris; pocket depth, gingival recession, electric pulp test, mobility, percussion test, sensitivity test. The extracted teeth were fixed buffered neutral formalin solution. It was decalcified using 4% nitric acid. Sliced histological samples observed using light microscope, for pulp status, and severeity of inflammation. 4 samples were excluded due to histologic sample discrepency. Thus 13 samples were subject to observation. 4 showed normal conditions. Focal reversable pulpitis was shown in 5 samples. Chronic pulpitis was observed 1 sample. Pulpal abscess was observed in 3 samples.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.10a
• /
• pp.97-102
• /
• 2001

This paper describes an investigation how to carry out model tests of deepwater moorings exceeding the basin depth range. A hybrid mooring model, a combination of mooring lines scaled model and a couple of linear springs, is taken into account as an equivalent substitute of a full depth mooring system. Such an idea is applied to the model test of an OTEC mooring system to be installed in 1000m deep ocean. A 1/25 scaled model test of surface vessel and the upper part of mooring system is performed at ocean engineering basin. Possibility and limitation of the hybrid mooring modeling is discussed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.4
• /
• pp.322-328
• /
• 2000

In this paper, we were investigated the detectability on various specimen in self-designed test field using the GPR system with three antenna elements. The GPR system was constantly radiated 730MHz frequency. To examine the detectability on various condition, the test were experimented using different materials, size and buried depth. As an adjusted wave-propagation velocity, the location of hyperbolic curve pattern were displayed B-scan CRT. And the pattern was exactly positioned when it was compared to the real buried-depth. Therefore, we can confirm similarity between the wave-propagation velocity and previous results.

• Journal of Korea Game Society
• /
• v.7 no.3
• /
• pp.31-38
• /
• 2007

In this paper, we proposed an effective visibility test architecture with improving the mid-texturing architecture. The proposed architecture uses the property of fragments that the visibility of adjacent fragments is identical, and performs only a single visibility test per fragment. To compare with the mid-texturing architecture, simulation results show that the bandwidth requirements and the cell area of the depth cache in the proposed architecture are reduce by 25% and 34%, respectively, in exchange for less than 5% performance decline.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.2
• /
• pp.1-10
• /
• 2017

This study carried out several laboratory tests such as water tank settlement test and two-dimensional water flow test to investigate settlement and scour characteristics of a square-shaped hybrid reef which was reinforced with geogrid. In addition, numerical analysis was also performed to find out scour characteristics of the square-shaped hybrid reef with different placement types (type A; straight placement type, type B; zigzag placement type). Laboratory test results indicated that settlement and scouring depth significantly reduced in hybrid reefs reinforced with geogrid, compared with those without reinforcement. Two-dimentional water flow tests and numerical test results also showed that scouring depth and flow velocity of placement type A more decreased than those of type B.

• Corrosion Science and Technology
• /
• v.20 no.6
• /
• pp.435-450
• /
• 2021

The interest in eco-friendly energy is increasing, and polymer electrolyte membrane fuel cell (PEMFC) is attracting attention as alternative power sources. Research on metallic bipolar plates, a fuel cell component, is being actively conducted. However, since the operating conditions of PEMFC, in which sulfuric acid (H₂SO₄) and hydrofluoric acid (HF) are mixed, are strong acidity, the durability of the metallic bipolar plate is very important. In this research, the electrochemical characteristics and corrosion damage behavior of 316L stainless steel, a material for metallic bipolar plates, were analyzed through potentiostatic corrosion tests with test times and chloride concentrations. As the test times and chloride concentrations increased, the current density and corrosion damage increased. As a result of observation with scanning electron microscope(SEM) and 3D microscope, both the depth and width of pitting corrosion increased with increases in test times and chloride concentrations. In particular, the pitting corrosion damage depth at test conditions of 6 hours and 1000 ppm chloride increased the most. The growth of the pitting corrosion damage was not directly proportional to time and increased significantly after a certain period.