• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.73-76
• /
• 2001

We deposited epitaxial $Ba_{0.6}$S $r_{0.4}$Ti $O_3$(BST) films having thickness of 400 nm on MgO(001) substrates, where a 10 nm thick $Ba_{1-x}$S $r_{x}$Ti $O_3$(x=0.1-0.7) interlayer was inserted between BST and MgO to manipulate the stress of the BST films. Since the main difference of those epitaxial BST films was the lattice constant of the interlayers, we were very successful in controlling the stress of the BST films. BST films under small tensile stress showed larger dielectric constant than that without stress as well as those under compressive stress. Stress relaxation was investigated using epitaxial BST films with various thicknesses grown on different interlayers. For BST films grown on $Ba_{0.7}$S $r_{0.3}$Ti $O_3$ interlayers, the critical thickness was about 600 nm. On the other hand, the critical thickness of single-layer BST film was less than 100 nm.00 nm.m.m.m.

• 한국표면공학회지
• /
• 제36권1호
• /
• pp.9-13
• /
• 2003

Plasma polymerized organic thin films were deposited on Si(100), glass and metal substrates at $25∼100 ^{\circ}C$ using thiophene and toluene precursors by PECVD method. In order to compare physical and electrochemical properties of the as-grown thin films, the effects of the RF plasma power in the range of 30∼100 W and deposition temperature on both corrosion protection efficiency and physical properties were studied. We found that the corrosion protection efficiency ($P_{k}$), which is one of the important factors for corrosion protection in the interlayer dielectrics of microelectronic devices application, was increased with increasing RF power. The highest $P_{k}$ value of plasma polymerized toluene film (85.27% at 70 W) was higher than that of the plasma polymerized thiophene film (65.17% at 100 W), indicating inhibition of oxygen reduction. The densely packed and tightly interconnected toluene film could act as an efficient barrier layer to the diffusion of molecular oxygen. The result of contact angle measurement showed that the plasma polymerized toluene films have more hydrophobic surface than those of the plasma polymerized thiophene films.

• 한국표면공학회지
• /
• 제43권3호
• /
• pp.127-131
• /
• 2010

Adhesion of DLC film is very significant property that exhibits wear resistance, chemical inertness and high hardness when being deposited to metal substrate. This study was considered that change adhesion of DLC film produced by Plasma Enhanced Chemical Vapor Deposition can be presented through inserting interlayer (Cr, Si-C:H). The thickness of interlayer was result of changing adhesion and residual stress. It was showed that the maximum 12 N of adhesion is on DLC film of Cr interlayer, and that a tendency is to be increased residual stress depend on the thickness. DLC film of Si-C:H interlayer represented 16 N of adhesion at $1{\mu}m$, whereas adhesion is decreased when the thickness is increased. For the interlayer at multi-layer, it was the best that adhesion of Cr/Si-C:H/DLC film was 33 N. Si-C:H interlayer at DLC film controled adhesion of the whole film. It was relaxed the internal stress of DLC film produced by inserting Cr, Si-C:H interlayer.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1971-1973
• /
• 2005

We fabricated an alumina membrane with nano-sized pore array by anodic oxidation using the thin film aluminum deposited on silicon wafer. It is important that the sample prepared by metal deposition method has a flat aluminum surface and a good adhesion between the silicon wafer and the thin film aluminum. The oxidation time was controlled by observation of current variation. The nano-sized pores with diameter of $60{\sim}120nm$ was obtained by $40{\sim}80$ voltage. The pore widening process was employed for obtaining the flat surface because the pores of the alumina membrane prepared by the fixed voltage method shows the structure of rough surface. Finally, the sample was immersed to the phosphoric acid with 0.1M concentration to etching the barrier layer. The sample will be applied to electronic sensors, field emission display, and template for nano- structure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1884-1886
• /
• 2005

KrF 펄스 레이저 증착법(pulsed laser deposition: PLD)으로 ZnO 박막을 증착하여 평판 디스플레이 소자 구동용 박막 트랜지스터(thin film transistor) 소자를 제작하였다. 전도성이 높은 실리콘웨이퍼(c-Si, 하부전극) 기판 위에 LPCVD 법으로 silicon nitride 박막을 절연막으로 형성하고, 다양한 공정 조건에서 펄스 레이저 증착법으로 제작한 ZnO 박막을 증착하여 채널층으로 하였으며, Al 박막을 증착하고 패터닝하여 소스 및 드레인 전극으로 하였다. ZnO 박막의 증착 시에 기판 온도를 다양하게 조절하고 산소 분압을 변화시켜 ZnO 박막의 특성을 조절하였다. 제작된 박막의 표면특성은 AFM(atomic force microscopy)로 분석하고, 결정특성은 XRD(X-ray diffraction)로 조사하였다. ZnO 박막의 전기적 특성은 Hall-van der Pauw 법으로 측정하였고, 광학 투과도(optical transparency)를 UV-visible photometer로 조사하였다. ZnO-TFT 소자는 $10^6$ 수준의 on-off ratio와 $2.4{\sim}6.1cm^2/V{\cdot}s$의 전계효과이동도(field effect mobility)를 보였다.

• 한국전기전자재료학회논문지
• /
• 제24권8호
• /
• pp.616-621
• /
• 2011

In this paper, CdS thin films, which were widely used window layer of the CdTe and the Cu(In,Ga)$Se_2$ thin film solar cell, were grown by chemical bath deposition, and effects of pH of reaction solution on the structural and optical properties were investigated. For pH<10.5, as the pH of reaction solution was higher, the deposition rate of CdS films was increased by improving ion-by-ion reaction in the substrate surface and the crystallinity of the films was improved. However, when the pH was higher than 10.5, the deposition rate was decreased because of smaller $Cd^{2+}$ ion concentration in the reaction solution. Also, the crystallinity of the films were deteriorated. The CdS films deposited at lower pH showed poor optical transmittance due to adsorbed colloidal particles, while the transmittance was improved for higher pH.

• 한국전기전자재료학회논문지
• /
• 제24권9호
• /
• pp.739-743
• /
• 2011

Ga doped ZnO (GZO)/Cu bi-layer films were deposited with RF and DC magnetron sputtering on glass substrate and then the effect of post deposition annealing temperature on the structural, optical and electrical properties of the films was investigated. The post deposition annealing process was conducted for 30 minutes in gas pressure of $1{\times}10^{-3}$ Torr and the annealing temperatures were 150 and $300^{\circ}C$. With increasing annealing temperature, GZO/Cu films showed an increment in the prefer orientation of ZnO (002) diffraction peak in the XRD pattern and the optical transmittance in a visible wave region was also increased, while the electrical sheet resistance was decreased. The GZO/Cu films annealed at $300^{\circ}C$ showed the highest optical transmittance of 70% and also showed the lowest electrical resistance of $85\;{\Omega}/{\Box}$ in this study.

• 한국전기전자재료학회논문지
• /
• 제31권4호
• /
• pp.238-243
• /
• 2018

A nanofiber was fabricated with carbon nanotubes for transparent electrodes. It was prepared with a composite solution of bio-molecules polycaprolactone (PCL) and multiwalled carbon nanotubes (MWCNTs) by electrospinning on a glass substrate, following which its electrical characteristics were investigated. The content of MWCNTs was varied during electrospinning, while that of PCL was fixed. Further, a nanometer-thick thin film of silver was deposited on the nanofiber layer using a thermal evaporator to improve the electrical characteristics; the sheet resistance significantly reduced after this deposition. The results showed that this carbon nanotube nanofiber has potential applications in biotechnology and as a flexible transparent display material.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 춘계학술대회 논문집
• /
• pp.96-97
• /
• 2015

확산을 이용한 표면 개질법인 Thermo-Reactive Diffusion(TRD) 기술 기반 2단 표면처리를 통해 고경도의 Nb(C,N) 코팅층을 고탄소 베어링강인 JIS-SUJ2강에 형성시켰다. 2단 표면처리는 암모니아 가스 질화와 분말 확산 코팅법으로 구성된 2step 열처리이다. 본 연구에서는 가스질화 화합물층의 두께가 코팅층 성장 거동에 어떤 영향을 미치는지 알아보기 위해서 $550^{\circ}C$에서 3, 6시간 암모니아 가스 분위기에서 가스질화를 실시하고, $900^{\circ}C$에서 3시간 분말 확산법을 통해 표면 코팅층을 형성하였다. 생성된 코팅층의 형상과 두께 측정을 광학현미경(OM) 과 주자전자현미경(SEM)을 통해 한 결과, 가스 질화는 약 10uu와 16um, 최종 코팅층은 약 정도 생성이 되었음을 확인하였다. 코팅층의 성분 분석은, EDS, FE-EPMA, XPS 분석을 통해서 실시하였다. EDS와 FE-EPMA 원소 mapping을 통해 모재에 비해 높은 농도의 Nb, C 그리고 N이 코팅층 내부에 존재함을 확인하였다. XPS분석의 결합에너지 peak를 통해 NbC, NbN 그리고 Nb-oxide가 생성이 되었음을 분석하였다. 생성된 코팅층의 경도는 low mode에서 10회 측정한 후 평균값을 내었고, 각각 Hv이었다.

• 한국산학기술학회논문지
• /
• 제3권2호
• /
• pp.115-119
• /
• 2002

본 연구에서는 자이로 펌프의 내구성 및 내마모성을 향상시키고자 로타와 붓싱 재질 개선방안을 조사하였다. 질화강과 SKD11 합금 부품에 스퍼터링 방법으로 TiN Coating과 가스질화법으로 표면처리를 행하였으며, 기지조직의 개선을 위하여 SKD11 합금의 열처리를 행하였다. 실험결과 TiN Coating부품은 펌프 작동 중 Coating층의 밀착력 부족으로 박리현상이 나타났으나, 가스질화 시 우수한 표면경도와 충분한 경화층으로 뜯김현상이 제거되었다. SKD11 합금의 열처리 탄화물 조절을 위한 SKD11 합금의 열처리 결과 경도가 증가하였다.