• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.3
• /
• pp.69-80
• /
• 2015

This paper is writing about developing magnet power supply. It is very important for power supply to obtain output current in high precision and high stability. As a switching noise and a power noise are the cause of disrupting the stability of output current, to remove these at the front end, low pass filter with 300Hz cutoff frequency is designed and placed. And also to minimize switching noise of the current into magnet and to stop abrupt fluctuations, output filter should be designed, when doing this, we design it by considering load has high value inductance. As power supply demands the stability of less than 5ppm, high precision 24bit(300nV/bit) analog digital converter is needed. As resolving power of 24bit(300nV/bit) analog digital converter is high, it is also very important to design the input stage of analog digital converter. To remove input noise, 4th order low pass filter is composed. Due to the limitation of clock, to minimize quantization error between 15bit DPWM and output of ADC having 24bit resolving power, ${\Sigma}-{\Delta}$ modulation is used and bit contracted DPWM is constituted. And before implementing, to maximize efficiency, simulink is used.

• Journal of Korea Foundry Society
• /
• v.29 no.4
• /
• pp.181-186
• /
• 2009

The interrelationship between new parameter ${\sigma}$ and maximum diameter $D_{max}$ is elaborated and discussed in comparison with four other glass forming ability (GFA) parameters, i.e. (1) super-cooled liquid region ${\Delta}T_x (=T_x - T_g)$, (2) reduced glass transition temperature $T_{rg} (=T_g/T_l)$, (3) K parameter $K (=[T_x-T_g]/[T_l -T_x])$, and (4) gamma parameter ${\gamma}(=[T_x]/[T_l+T_g])$ in Ca-based bulk metallic glass (BMG) systems. The ${\sigma}$ parameter, defined as ${\Delta}T^*{\times}P^'$, has a far better correlation with $D_{max}$ than the GFA parameters suggested so far, clearly indicating that the liquid phase stability and atomic size mismatch dominantly affect the GFA of Ca-based BMGs. Thus, it can be understood that the GFA of BMGs can be properly described by considering structural aspects for glass formation as well as thermodynamic and kinetic aspects for glass formation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.561-565
• /
• 2010

Stainless steel sheets are widely used as structural materials for the manufacture of railroad cars and commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. For the fatigue design of gas welded joints such as fillet joints and plug joints, it is necessary to obtain information on the stress distribution at the weldment and the fatigue strength of the gas welded joints. Moreover the influence of the geometrical parameters corresponding to the gas welded joints on the stress distribution and fatigue strength must be evaluated. ${\Delta}P-N_f$ curves were obtained from the data recorded in fatigue tests. Using these results, the ${\Delta}P-N_f$ curves were rearranged according the relation between $\Delta\sigma-N_f$ and the maximum stress at the edge of the fillet welded joint.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.231-234
• /
• 2002

A transceiver for ADSL systems contains an interpolated combfilter, halfband filters, oversampling sigma delta modulator, a current steering DAC and an analog filler. The circuit complexity of the architecture makes it necessary to use behavioral models to determine the system features. For this reason, we need a specific behavioral simulation environment using the Matlab program. The Matlab is crucial for these circuits to be rapidly incorporated in larger systems, in particular in the context of mixed-signal-test schemes. Design trade-off among the blocks has also been discussed. The design methodology is based on behavioral design and CMOS process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.294-301
• /
• 2017

This paper presents a low power ${\Sigma}{\Delta}$ modulator for an implantable chip to acquire a bio-signal such as EEG, DBS, and EMG. In order to reduce a power consumption of the proposed fourth order modulator, two op-amps utilized for the first two integrators are reconfigured to drive the second two integrators. The KT/C noise reduction circuit in the first two integrators is employed to enhance SNR of the modulator. The proposed circuit was fabricated in a 0.18 um CMOS n-well 1 poly 6 metal process with the active chip core area of $900um{\times}800um$ and the power consumption of 830 uW. Measurement results were demonstrated to be SNDR of 76 dB, DR of 77 dB, ENOB of 12.3 bit at the input frequency of 250 Hz and the clock frequency of 256 kHz. FOM1 and FOM2 were measured to be 41 pJ/step and 142.4 dB, respectively.

• Journal of the Korean Chemical Society
• /
• v.44 no.3
• /
• pp.184-189
• /
• 2000

ab initio molecular orbitaI calculation is performed to estimate the substituent effects for meta-substituted pyridines. Electrostatic potentials are obtained from ab initio wavefunctions of the optimized structures for the meta-substituted pyridines. Electrostatic potenhals are shown to be minimum at nitrogen atom of pyridines. The potenttial minima are good correlated with the substituent constants, ${\sigma}_m$ and with the ${\Delta}pK_a$, respectively. It is found that the electrostatic potential minima can be used as a useful measure of substituent effects.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.276-281
• /
• 2010

A 2.5 V feed-forward second-order deltasigma modulator for audio application is presented. A 9-level quantizer with a tree-structured dynamic element matching (DEM) was employed to improve the linearity by shaping the distortion resulted from the capacitor mismatch of the feedback digital-toanalog converter (DAC). A chopper stabilization technique (CHS) is used to reduce the flicker noise in the first integrator. The prototype delta-sigma analogto-digital converter (ADC) implemented in a 65 nm 1P8M CMOS process occupies 0.747 $mm^2$ and achieves 109.1 dB dynamic range (DR), 85.4 dB signal-to-noise ratio (SNR) in a 24 kHz audio signal bandwidth, while consuming 14.75 mW from a 2.5 V supply.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2017.04a
• /
• pp.1020-1023
• /
• 2017

Viola와 Jones가 제안한 AdaBoost(Adaptive Boosting) 알고리즘은 기존의 물체 검출기에 비해 속도와 정확도 면에서 우수하여 실시간 물체 검출기로써 좋은 성능을 보인다. 하지만 여전히 많은 계산량 때문에 성능이 낮은 임베디드 환경에서는 실시간 검출에 대한 아쉬움이 있다. 본 논문에서는 계산량을 줄이기 위해 모션 검출을 통해 배경 영역을 제거하고 얼굴 영역을 추정한다. 제거된 배경 영역은 AdaBoost 알고리즘의 검출 과정에서 제외되며 추정된 얼굴 영역에 대해서만 검출을 하게 된다. 모션검출은 ${\Sigma}-{\Delta}$(Sigma-Delta) 배경 추정에 기반한 알고리즘을 사용한다.

• Bulletin of the Korean Mathematical Society
• /
• v.32 no.1
• /
• pp.123-132
• /
• 1995

Our interest is to study the existence of positive solutions to the following elliptic system involving competing interaction $$ (1) { -\partial(x,u,\upsilon)\Delta u = uf(x,u,v) { - \psi(x,u,\upsilon)\Delta \upsilon = \upsilon g(x,u,\upsilon) { \frac{\partial n}{\partial u} + ku = 0 on \partial\Omega { \frac{\partial n}{\partial\upsilon} + \sigma\upsilon = 0 $$ in a bounded region $\Omega$ in $R^n$ with a smooth boundary, where the diffusion terms $\varphi, \psi$ are strictly positive nondecreasing function, and k, $\sigma$ are positive constants. Also we assume that the growth rates f, g are $C^1$ monotone functions. The variables u, $\upsilon$ may represent the population densities of the interacting species in problems from ecology, microbiology, immunology, etc.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.48-53
• /
• 1999

We demonstrate small-scale high-T$_c$ superconductor RSFQ(Rapid Single Flux Quantum) circuits using multilayer bicrystal technology. An RSFQ balanced comparator is demonstrated with good current resolution, and its operating conditions are discussed in some detail. A single-loop delta-sigma modulator is realized adding a feedback loop to the comparator. The effect of the feedback is confirmed by dc measurement and simulation. A design of an RSFQ toggle flip-flop with the same multilayer bicrystal technology is suggested.