• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.41-43
• /
• 1999

Among the feffoelectric thin films that have been widely investigated for ferroelectric random access memory (FRAM) applications, SrBi$_2$Ta$_2$$O_{9}$ thin film is appropriate to memory capacitor materials for its excellent fatigue endurance. However, very few studies on etch properties of SBT thin film have been reported although dry etching is an area that demands a great deal of attention in the very large scale integrations. In this study, the a SrBi$_2$Ta$_2$$O_{9}$ thin films were etched by using magnetically enhanced inductively coupled Ar/CHF$_3$ plasma. Etch properties, such as etch rate, selectivity, and etched profile, were measured according to gas mixing ratio of CHF$_3$(Ar$_{7}$+CHF$_3$) and the other process conditions were fixed at RF power of 600 W, dc bias voltage of 150 V, chamber pressure of 10 mTorr. Maximum etch rate of SBT thin films was 1750 A77in, under CHF$_3$(Ar+CHF$_3$) of 0.1. The selectivities of SBT to Pt and PR were 1.35 and 0.94 respectively. The chemical reaction of etched surface were investigated by X-ray photoelectron spectroscopy (XPS) analysis. The Sr and Ta atoms of SBT film react with fluorine and then Sr-F and Ta-F were removed by the physical sputtering of Ar ion. The surface of etched SBT film with CHF$_3$(Ar+CHF$_3$) of 0.1 was analyzed by secondary ion mass spectrometer (SIMS). Scanning electron microscopy (SEM) was used for examination of etched profile of SBT film under CHF$_3$(Ar+CHF$_3$) of 0.1 was about 85˚.85˚.˚.

• Journal of Information Display
• /
• v.12 no.1
• /
• pp.47-50
• /
• 2011

Highly stable amorphous indium.gallium.zinc-oxide (a-IGZO) thin-film transistors (TFTs) were fabricated with an etchstopper and via-hole structure. The TFTs exhibited 40 $cm^2$/V s field-effect mobility and a 0.21 V/dec gate voltage swing. Gate-bias stress induced a negligible threshold voltage shift (${\Delta}V_{th}$) at room temperature. The excellent stability is attribute to the via-hole and etch-stopper structure, in which, the source/drain metal contacts the active a-IGZO layer through two via holes (one on each side), resulting in minimized damage to the a-IGZO layer during the plasma etching of the source/drain metal. The comparison of the effects of the DC and AC stress on the performance of the TFTs at $60^{\circ}C$ showed that there was a smaller ${\Delta}V_{th}$ in the AC stress compared with the DC stress for the same effective stress time, indicating that the trappin of the carriers at the active layer-gate insulator interface was the dominant degradation mechanism.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.214-214
• /
• 1999

다이아몬드를 반도체용 열방산용기판 등으로 사용하기 위해서는 수백 $\mu\textrm{m}$ 두께의 대면적 웨이퍼가 요구된다. 이를 위해서 DC are jet CVD, MW PACVD, DC PACVD 등이 개발되어, 현재 4"에서 8"까지의 많은 문제를 일으키고 있다. 본 연구에서는 multi-cathode DC PACVD법에 의한 4" 다이아몬드 웨이퍼의 합성과 합성된 막의 특성변화에 대한 연구를 수행하였다. 또한, 웨이퍼의 휨과 crack 발생거동과 대한 고찰을 통래 휨과 crack이 없는 웨이퍼의 제작방법을 고안하였다. 사용된 음극의 수는 일곱 개이며, 투입된 power는 각 음극 당 약 2.5kW(4.1 A-600V)이었다. 사용된 기판의 크기는 직경 4"이었다. 합성압력은 100Torr, 가스유량은 150sccm, 증착온도는 125$0^{\circ}C$~131$0^{\circ}C$, 수소가스네 메탄조성은 5%~8%이었다. 합성 중 막에 인가되는 응력은 합성 중 증착온도의 변화에 의해 제어하였다. 막의 결정도는 Raman spectroscopy 및 열전도도를 측정을 통해 분석하였다. 성장속도 및 다이아몬드 peak의 반가폭은 메탄조성 증가(5%~8%)에 따라 증가하여 각각 6.6~10.5$\mu\textrm{m}$/h 및 3.8~5.2 cm-1의 분포를 보였다. 6%CH4 및 7%CH4에서 합성된 웨이퍼에서 측정된 막의 열전도도는 11W/cmK~13W/cmK 정도로 높게 나타났다. 막두께의 uniformity는 최대 3.5%로 매우 균일하였다. 막에 인가되는 응력의 제어로 직경 4"k 합성면적에서 두께 1mm 이상의 균열 및 휨이 없는 다이아몬드 자유막 웨이퍼를 합성할 수 있었다.다이아몬드 자유막 웨이퍼를 합성할 수 있었다.active ion에 의해 sputtering 이 된다. 이때 plasma 처리기의 polymer 기판 후면에 magnet를 설치하여 높은 ionization을 발생시켜 처리 효과를 한층 높여 주었다. 이 plasma 처리는 표면 청정화, 표면 etching 이 동시에 행하는 것과 함께 장시간 처리에 의해 표면에서는 미세한 과, C=C기, -C-O-의 극성기의 도입에 의한 표면 개량이 된다는 것을 관찰할 수 있다. OPP polymer 표면을 Ar 100%로 plasma 처리한 경우 C-O, C=O 등의 carbonyl가 발생됨을 알 수 있었다. C-O, C=O 등의 carbynyl polor group이 도입됨에 따라 sputter된 Al의 접착력이 향상됨을 알 수 있으며, TEM 관찰 결과 grain size도 상당히 작아짐을 알 수 있었다.onte-Carlo 방법으로 처리하였다. 정지기장해석의 경우 상용 S/W인 Vector Fields를 사용하였다. 이를 통해 sputter 내 플라즈마 특성, target으로 입사하는 이온에너지 및 각 분포, 이들이 target erosion 형상에 미치는 영향을 살펴보았다. 또한 이들 결과로부터 간단한 sputtering 모델을 사용하여 target으로부터 sputter된 입자들이 substrate에 부착되는 현상을 Monte-Carlo 방법으로 추적하여 성막특성도 살펴보았다.다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인 측면에서도 고부가 가치의 제품 개발에 따른 새로운 수요 창출과 수익률 향상, 기존의 기능성 안료를 나노(nano)화하여 나노 입자를 제조, 기존의 기능성 안료에 대한 비용 절감 효과등을 유도 할 수 있다. 역시 기술적인 측면에서도 특수소재 개발에 있어 최적의 나노 입자 제어기술 개발 및 나노입자를 기능성 소재로 사용하여 새로운 제품의 제조와 고압 기상

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.159-162
• /
• 2002

Ferroelectric $YMnO_{3}$ thin films were etched with $Ar/Cl_{2}$ and $CF_{4}/Cl_{2}$ inductivly coupled plasma (ICP). The maximum etch rate of $YMnO_{3}$ thin film was $300{\AA}/min$ at a $Ar/Cl_{2}$ gas mixing ratio of 2/8, a RF power of 800 W, a dc bias of 200 V, a chamber pressure of 15 mTorr, and a substrate temperature of ${30^{\circ}C}$. From the X-ray photoelectron spectroscopy (XPS) analysis ， yttrium not only etched by chemical reactions with Cl radicals, but also assisted by Ar ion bombardments in $Ar/Cl_{2}$ plasma. In $CF_{4}/Cl_{2}$ plasma, yttrium are remained on the etched surface of $YMnO_{3}$ and formed of nonvolatile YFx compounds Manganese etched effectively by chemical reactions with Cl and F radicals. From the X-ray diffraction (XRD) analysis, the (0004) diffraction peak intensity of the $YMnO_{3}$ thin film etched in $Ar/Cl_{2}$ plasma shows lower value than that in $CF_{4}/Cl_{2}$ plasma. It is indicates that the crystallinty of $YMnO_{3}$ thin film is more easily damaged by the Ar ion bombardment than the changes of stoichiometry due to nonvolatile etch by-products.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.167-170
• /
• 1998

To apply diamond films in microelectromechanical systems(MEMS), it is necessary to develop the patterning technologies of diamond films in the micrometer scale. In this paper, three different kinds of technologies for patterning CVD diamond films carried out by us were demonstrated: selective growth by improved diamond nucleation in DC bias-enhanced microwave plasma chemical vapor deposition (MPCVD) system, selective growth of seeding using diamond-particle-mixed photoresist, and selective etching of oxygen ion beam using Al as the mask. It was show that high selectivity and precise patterns had been achieved, and all the processes were compatible with IC process.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.115-121
• /
• 1995

A mask for x-ray lithography is fabricated with SiN membrane and WTi absorber. SiN membrane is deposited by plasma enhanced chemical vapor deposition, and the stress of SiN membrane is controlled to be less than 100 MPa by rapid thermal annealing. WTi absorber is reactively deposited by DC-magnetron type sputter, and the working gases are argon and nitrogen. Added nitrogen is contributed to the stress of WTi absorber. The stress of WTi absorber is controlled to be less than $\pm$ 100 MPa by controlling the deposition pressure. 10$\mu$m WTi pattern is delineated on SiN membrane by dry etching technique.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.285-285
• /
• 2011

EUVL (Extreme Ultra Violet Lithography) is one of competitive lithographic technologies for sub-30nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance since the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.39-47
• /
• 2003

Cr thin films were deposited on photosensitive polyimide substrates by RF bias sputtering and DC sputtering and the interfaces between Cr thin film and polyimide were observed using TEM. When the polyimide surface was in-situ RF plasma cleaned at the RF power density of 0.13-2.12 $W/cm^2$, increasing of RF power density changed the morphology of polyimide surfaces from round dig to sharp shape, and surface roughness increased by anisotropic etching. The intermixed layer-like interfaces between Cr and polyimide were observed in the RF bias sputtered specimens. This interface seems to be formed due to the RF cleaning effect; the polyimide surface was RF plasma cleaned while RF power was increased to the setting point before Cr deposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.213-216
• /
• 2001

Etching behaviors of ferroelectric $YMnO_3$ thin films were studied by an inductively coupled plasma (ICP). Etch characteristic on ferroelectric $YMnO_3$ thin film have been investigated in terms of etch rate, selectivity and etch profile. The maximum etch rate of $YMnO_3$ thin film is $300{\AA}/min$ at $Ar/Cl_2$ of 2/8, RF power of 800W, dc bias voltage of 200V, chamber pressure of 15mTorr and substrate temperature of $30^{\circ}C$. Addition of $CF_4$ gas decrease the etch rate of $YMnO_3$ thin film. From the results of XPS analysis, YFx compounds were found on the surface of $YMnO_3$ thin film which is etched in $Ar/Cl/CF_{4}$ plasma. The etch profile of $YMnO_3$ film is improved by addition of $CF_4$ gas into the $Ar/Cl_2$ plasma. These results suggest that fluoride yttrium acts as a sidewall passivants which reduce the sticking coefficient of chlorine on $YMnO_3$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.933-938
• /
• 2002

(Ba,Sr)TiO$_{4}$ (BST) thin films on Pt/Ti/SiO$_{2}$/Si substrates were deposited by a sol-gel method and the etch characteristics of BST thin films have been investigated as a function of gas mixing ratio. The maximum etch rate of the BST films was 440 $AA$/min under such conditions as: CF$_{4}$(CF$_{4}$＋Ar) of 0.2, RF-power of 700 W, DC-bias voltage of -200 V, pressure of 15 mTorr and substrate temperature of 30 $^{circ}C$. The selectivities of BST to Pt, SiO$_{2}$ and PR were 0.38, 0.25 and 0.09, respectively. In the XPS (X-ray photoelectron spectroscopy) analysis, Barium (Ba) and Strontium (Sr) component in BST thin films formed low volatile compounds such as BaFx, SrFx, which are forms by the chemical reaction with F atoms and is removed by Ar ion bombardment. Titanium (Ti) is removed by chemical reaction such as TiF with ease. The result of secondary ion mass spectrometry (SIMS) analysis confirmed the existence of the BaFx, SrFK, TiFx.