• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.1047-1050
• /
• 2002

In this paper, grinding characteristics of cylindrical plunge grinding in 200m/sec of grinding velocity was investigated by use of vitrified CBN wheel. From the experimental result, it was convinced that grinding power is decreased 2.5times and grinding efficiency is heightened 3times more according to increasing wheel velocity 80m/sec to 200m/sec And also, be expected to improvement of surface roughness and roundness by increasing the wheel velocity.

• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.41-48
• /
• 2010

A visualization study to evaluate bubble motion in a tab water filled cylindrical tank with a varying flow rate of compressed air is conducted. The flow rate of compressed air varies from 1 to 5 L/min. Time resolved images are acquired by a high speed camera in 10 bit gray level at 100 fps and the measurement volume is irradiated by a 230 W halogen lamp. It is observed that there are three different regions; the bubble formation region, the rising bubble region and the free surface region. During the rise of bubble, the shape is changed as if an elastic body. Based on the binarized bubble image, the mean diameters of rising bubbles are estimated at beneath of the free surface. As the gas flow rate increases, the mean diameter is increased and the rising velocity also increases with buoyancy force.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.93-96
• /
• 2007

This paper presents a theoretical approach to describe the vibration characteristics in the 1-3 piezoelectric composite arrayed on a cylindrical surface. By homogenizing the composite composed of a piezoelectric ceramic and a polymer the physically useful parameters were defined and then used to derive the governing equation of radial motion for the cylindrical 1-3 piezoelectric composite. Applying mechanical and electric boundary conditions has yielded a characteristic equation for radial vibration of the composite. Theoretical calculations of the resonance frequency have been compared with those obtained by the finite-element analysis and have shown a good agreement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.961-964
• /
• 1997

In this paper, grinding characteristics of ultra high speed cylindrical plunge grinding was investigated by use of vitrified CBN wheel. From the experimental result, it was convinced that grinding power is decreased according to the increase of wheel and workpiece speed due to changing of grinding mechanism which decreases depth of cut and length of contact curve according to increment of wheel speed. And also, stock removal reduction of each gram lead to improvement of surface roughness by increasing the wheel speed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.10
• /
• pp.867-873
• /
• 2002

We have designed and fabricated the slidacs type automatic voltage regulator(SVR) that is able to control the output voltage continuously according to load variation. Especially, the frictions between the surface of contact of the slidacs coils and the output wire moving shaft arc reduced by modifying the mechanical configuration of surface of contact of slidacs from the conventional sliding one into the proposed rotary one composed of cylindrical bearing. Thus, SVR using cylindrical bearing proposed in this study has less noise than the conventional one owing to the reduction of friction, and its breakdown ratio caused by the abrasion of contact materials is reduced as well. We have designed U motor driving circuit for controlling the output wire moving shaft, and introduced the digital control method using the pulse width modulation(PWM) output for controlling DC motor.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.151-152
• /
• 2009

We coated $TiO_2$ thin films on particles by a rotating cylindrical plasma chemical vapor deposition (PCVD) process and investigated the effects of various process variables on the morphology and growth of thin films. The polypropylene (PP) particles were rotated with the cylindrical PCVD reactor and they were coated with $TiO_2$ thin films uniformly by the deposition of thin mm precursors in the gas phase. The $TiO_2$ thin films were coated on the PP particles uniformly and the thickness of thin films almost proportional to the deposition time. The $TiO_2$ thin films grew more quickly on the PP particles with increasing rotation speed of the reactor. This study shows that a rotating cylindrical PCVD reactor can be a good method to coat high-quality $TiO_2$ thin films uniformly on particles.

• Geomechanics and Engineering
• /
• v.9 no.5
• /
• pp.631-644
• /
• 2015

This article considers the problems of cylindrical bending of functionally graded plates in which material properties vary through the thickness. The variation of the material properties follows two power-law distributions in terms of the volume fractions of constituents. In addition, this paper considers orthotropic materials rather than isotropic materials. The traction-free condition on the top surface is replaced with the condition of uniform load applied on the top surface. Numerical results are presented to show the effect of the material distribution on the deflections and stresses. Results show that, all other parameters remaining the same, the studied quantities (stress, deflection) of P-FGM and E-FGM plates are always proportional to those of homogeneous isotropic plates. Therefore, one can predict the behaviour of P-FGM and E-FGM plates knowing that of similar homogeneous plates.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.111-120
• /
• 2011

A two-dimensional analytical model for deriving the threshold voltage of a short channel fully depleted (FD) cylindrical/surrounding gate MOSFET (CGT/SGT) is suggested. By taking into account the lateral variation of the surface potential, introducing the natural length expression, and using the Bessel functions of the first and the second kinds of order zero, we can derive potentials in the gate oxide layer and the silicon core fully two-dimensionally. Making use of these potentials, the minimum surface potential can be obtained to derive the threshold voltage as a closed-form expression in terms of various device parameters and applied voltages. Obtained results can be used to explain the drain-induced threshold voltage roll-off of a CGT/SGT in a unified manner.

• 한국가시화정보학회:학술대회논문집
• /
• 2002.11a
• /
• pp.81-84
• /
• 2002

Dispersion of coolant jets in a film cooling flow field is the result of a highly complex interaction between the film cooling jets and the mainstream. In order to investigate the effect of blowing ratios on the film cooling of turbine blade, cylindrical body model was used. Mainstream Reynolds number based on the cylinder diameter was $7.1\;\times\;10^4$. The free-stream turbulence intensity kept at $5.0\%$ by using turbulence grid. The effect of coolant flow rates was studied for blowing ratios of 0.9, 1.3 and 1.6, respectively. The temperature distribution of the cylindrical model surface is visualized by infrared thermography (IRT). Results show that the film-cooling performance may be significantly improved by controlling the blowing ratio. As blowing ratio increases, the adiabatic film cooling effectiveness is more broadly distributed and the area protected by coolant increases. The mass flow rate of the coolant through the first-row holes is less than that through the second-row holes due to the pressure variation around the cylinder surface.

• Structural Engineering and Mechanics
• /
• v.76 no.5
• /
• pp.599-611
• /
• 2020

A state-space method is developed to investigate the time-dependent behaviors of an angle-ply cylindrical shell in cylindrical bending with surface-bonded piezoelectric layers. Both the interfacial diffusion and sliding are considered to describe the properties of the imperfect interfaces. Particularly, a matrix reduction technique is adopted to establish the transfer relations between the elastic and piezoelectric layers of the laminated shell. Very different from our previous paper, in which an approximate numerical technique, i.e. power series expansion method, is used to deal with the time-dependent problems, the exact solutions are derived in the present analysis based on the piezoelasticity equations without any assumptions. Numerical results are finally obtained and the effects of imperfect interfaces on the electro-mechanical responses of the laminated shell are discussed.