• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.128-139
• /
• 1998

In this paper, a finite element method for predicting the temperature and stress distributions in micro-machining is presented. The work material is oxygen-free-high-conductivity copper(OFHC copper) and its flow stress is taken as a function of strain, strain rate and temperature in order to reflect realistic behavior in machining process. From the simulation, a lot of information on the micro-machining process can be obtained; cutting force, cutting temperature, chip shape, distributions of temperature and stress, etc. The calculated cutting force was found to agree with the experiment result with the consideration of friction characteristics on chip-tool contact region. Because of considering the tool edge radius, this cutting model using the finite element method can analyze the micro-machining with the very small depth of cut, almost the same size of tool edge radius, and can observe the 'size effect' characteristic. Also the effects of temperature and friction on micro-machining were investigated.

• 대한전자공학회논문지
• /
• 제27권1호
• /
• pp.51-58
• /
• 1990

NPN Si bipolar transistors with two different emitter widths are designed and fabricated. The effects of the emitter width on the small signal parameters of BJTs are measured and discussed. A new ac method for determining the current gain, the cut off frequency and the internal capacitances from the input impedance circle characteristics as a function of the varied external series resistances is presented. This method allows an accurate characterization of bipolar transistors with high current gain. The variation of the I-V curves of the emitter junction with the reverse collector junction voltages is discussed from the changes in the intsrinsic base resistances.

• 대한안전경영과학회지
• /
• 제3권1호
• /
• pp.35-44
• /
• 2001

Today's environment of enterprise is changing. They have to face customers' demands with the right product, the right service and supply them at the right time. And aIso cut down logistics and inventory cost and bring up the Profit as much as they can. This means the change of putting enterprise first in importance to putting customer first in importance. therefore to correspond to customer's demand, shorting lead time is becoming a essential condition. The answer to this changes of environment is supply chain management In this study, we use Goldratt's drum-buffer-rope scheduling in between manufacturer and supplier. And when shortage of inventory occur, search for the supply chain's CCR. Pressing CCR for more production, and supply Inventory from logistic center to guide for inventory buffing. using logistic warehouse between manufacturer and supplier, can execute function of buffer.

• Journal of the Korean Data and Information Science Society
• /
• 제16권2호
• /
• pp.477-505
• /
• 2005

This paper gives a computer code that gives p-value's for Kendall's Tau table. The code centers around finding the cumulative frequency of a given Sigma value. Current tables usually give critical values for given cut-off percentages. For small sample sizes the critical values may be inexact, and for large samples the values are not be published. SPSS has a built in function for finding the Kendall rank correlation, but the output does not include the Sigma value. Before the code is given, this paper will concentrate around how to find the Sigma value, and the related tau statistic. The computer code is written in MATLAB, but the ideas can be easily transferred to different languages.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.584-586
• /
• 2005

The stroke of piston in the linear compressor driven by LPMSM can be obtained from integrating the input voltage and current of LPMSM, and may be diverged due to dc components In the voltage and current. The strategy to prevent the divergence of stroke using both the high-pass filter and dc offset compensation was suggested. The equations for the magnitude and phase of the stroke and also dc offset including the stroke are derived as a function of the cut-off frequency of HPF. The performance of stroke calculation scheme has been verified by experimentally on a linear compressor drive system, where the control was implemented by a 16-bit DSP.

• 대한전기학회논문지:전력기술부문A
• /
• 제49권2호
• /
• pp.43-49
• /
• 2000

It is a complex process to analyze power system voltage stability problems with all of the dynamics of a system, because a large power network system sophisticatedly consists of generators, lines, loads and so forth. So we considered the dynamics of loads so as to analyze voltage stability method- by carrying out an analysis of steady state voltage stability and dynamic voltage stability simultaneously. To perform a steady state voltage stability program in advance makes it possible to cut down on laborious calculations so that an analysis of dynamic voltage stability becomes concise. The validity and efficiency of the method presented in this paper were verified by applying the IEEE 14 bus system.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.8-13
• /
• 2010

The shaft surface machining is a popular machine for studying descale machine design and process in automobile industry. In this study, the descale design machine of cutting shaft surface was conducted for the detection of a tool failure in surface process. Induction harden surface is used as analyzing function to detect a sudden change in cutting process level. A preliminary stepped workpiece which had a hard condition was cut by the surface tool and a tool process obtained cutting force machine. At machine failure, the results were suddenly increased and the detailed surfaces were extremely obtained.

• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.1-6
• /
• 2010

The wavelet transform is a popular tool for studying intermittent and localized phenomena in signals. In this study the wavelet transform of cutting force signals was conducted for the detection of a tool failure in turning process. We used the Daubechies wavelet analyzing function to detect a sudden change in cutting signal level. A preliminary stepped workpiece which had intentionally a hard condition was cut by the inserted cermet tool and a tool dynamometer obtained cutting force signals. From the results of the wavelet transform, the obtained signals were divided into approximation terms and detailed terms. At tool failure, the approximation signals were suddenly increased and the detailed signals were extremely oscillated just before tool failure.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1998년도 PROCEEDINGS OF THE 15TH KACG TECHNICAL MEETING-PACIFIC RIM 3 SATELLITE SYMPOSIUM SESSION 4, HOTEL HYUNDAI, KYONGJU, SEPTEMBER 20-23, 1998
• /
• pp.53-53
• /
• 1998

Four valence of Chromium ion doped Yttrium Aluminum Garnet crystals were grown by Floating Zone and Czochralski methods. Changes of valence for Chromium (3+) ion to Chromium (4+) were achieved by substitution of Yttrium ion in dodecahedral site to Calcium and by substitution of Aluminum in octahedral site to Magnesium. Growth conditions for high quality of crystals were investigated. Grown crystals were cut and polished and then observed various types of defects. Characterizations by means of measurement of density and lattice parameter as a function of solidification fraction were performed. Results of Q-switching test using grown crystals were also reported.

• 산업경영시스템학회지
• /
• 제24권62호
• /
• pp.21-32
• /
• 2001

The two-dimensional guillotine cutting problem is to maximize sum of piece profits that cut from one stock rectangle and widely applied in the industry. The branch-and-bound method for this problem uses complementarily several upper bounds(the Gilmore and Gomoryp[8]'s two-dimensional knapsack function and the Hifi and Zissimopoulos[10]'s method using one-dimensional knapsack problem, etc) to reduce the number of searched nodes. These upper bounds has a shortcoming that does not consider the bound and layout of pieces simultaneously. In this paper, we propose an efficient upper bound which can complement the shortcoming of existing upper bounds. The proposed upper bound needs less memory spaces and computing time. Computational results show that the proposed upper bound significantly contribute to reduce the computational amount of time and number of searched nodes in tree.