• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.306-306
• /
• 2010

A high density (> $10^{11}\;cm^{-3}$) and low electron temperature (< 2 eV) plasma is produced by using a conventional HF (13.56 MHz) plasma enhanced chemical vapor deposition (PECVD) with an additional ultra high frequency (UHF, 314 MHz) plasma source utilizing two parallel antenna assembly. It is applied for the high rate synthesis of high quality nanocrystalline silicon (nc-Si) films. A high deposition rate of 1.8 nm/s is achieved with a high crystallinity (< 70%), a low spin density (< $3{\times}10^{16}\;cm^{-3}$) and a high light soaking stability (< 1.5). Optical emission spectroscopy measurements reveal emission intensity of $Si^*$ and $SiH^*$, intensity ratio of $H{\alpha}/Si^*$ and $H{\alpha}/SiH^*$ which are closely related to film deposition rate and film crystallinity, respectively. A high flux of precursor and atomic hydrogen which are produced by an additional high excitation frequency is effective for the fast deposition of highly crystallized nc-Si films without additional defects.

• Journal of the Korean Ceramic Society
• /
• v.44 no.11
• /
• pp.645-649
• /
• 2007

The $La_{0.7}Sr_{0.3}MnO_3$ was deposited on $SiO_2/Si$ substrate by RF magnetron sputtering. The oxygen gas flow rate was changed from 0 to 80 sccm and the substrate temperature was $350^{\circ}C$. The oxygen gas flow rate was changed to control the growth orientation and crystalline state of the film. Relatively high TCR (temperature coefficient of resistance) value (-2.33%/K) was obtained when comparing with the reported values of the films prepared by using high substrate anneal temperature. The decrease in the sheet resistance and TCR value were observed when grain size of the film increased with the increase of oxygen gas flow rate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.232-232
• /
• 2012

The doping of semiconducting elements is essential for the development of silicon quantum dot (QD) solar cells. Especially the doping elements should be activated by substitution at the crystalline sites in the crystalline silicon QDs. However, no analysis technique has been developed for the analysis of the activated dopants in silicon QDs in $SiO_2$ matrix. Secondary ion mass spectrometry (SIMS) is a powerful technique for the in-depth analysis of solid materials and the impurities analysis of boron and phosphorus in semiconductor materials. For the study of diffusion behaviour of B and P by SIMS, Si/$SiO_2$ multilayer films doped by B or P were fabricated and annealed at high temperatures for the activated doping of B and P. The distributions of doping elements were analyzed by SIMS. Boron found to be preferentially distributed in Si layer rather than the $SiO_2$ layer. Especially the B in the Si layers was separated to two components of an interfacial component and a central one. The central component was understood as the activated elements. On the other hand, phosphorus did not show any preferred diffusion.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.7-12
• /
• 2003

The $Bi_{3.3}La_{0.7}O_{12}$(BLT) capacitors with Metal-Ferroelectric-Insulator-Silicon structure were prepared on $SiO_2/Si$ substrates by using sol-gel method. The BLT thin films annealed at $650^{\circ}C$ and $700^{\circ}C$ showed randomly oriented perovskite crystalline structures. The full with at half maximum (FWHM) of the (117) main peak was decreased from $0.65^{\circ}$ to $0.53^{\circ}$ with increasing the annealing temperature from $650^{\circ}C$ to $700^{\circ}C$, indicating the improvement in the crystalline quality of the film. In addition, the grain size and $R_rms$ , values were increased with increasing the annealing temperatures, showing the rough film surface at higher annealing temperatures. From the capacitance-voltage (C-V) measurements, the memory window voltage of the BLT film annealed at $700^{\circ}C$ was found to be about 0.7 V at an applied voltage of 5 V. The leakage current density of the BLT film annealed at $700^{\circ}C$ was about $3.1{\times}10^{-8}A/cm^2$.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.250-253
• /
• 1990

A single-crystalline epitaxial film of GaAs has been grown on Si using an ionized cluster beam technique. The native oxide layer on the silicon substrate was removed at $550^{\circ}C$ by use of an accelerated arsonic ion beam, instead of a high-temperature desorption. During the growth the substrate temperature was maintained at $550^{\circ}C$. Transmission electron microscopy and electron diffraction data suggest that the eats layer is an epitaxially grown single-crystalline layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1026-1029
• /
• 2001

Zinc films have been deposited onto various buffer layers, Al, Al-Cu, Ag and Ag-Al, by vacuum evaporation method in order to investigate the film microstructure and its consequence on the film growth. Zn films were grown onto Al buffer layers with faster rates than on Ag buffer layers, because of the presence of preferred growth orientation. Especially, in the Zn film formation on the Ag layers, intermetallic compounds AgZn was formed to cause the different growth orientation from Zn film obtained on the Al layers.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.1
• /
• pp.26-29
• /
• 2006

Transparent ZnO thin films were prepared by KrF pulsed laser deposition (PLD) technique and applied to a bottom-gate type thin film transistor device as an active channel layer. A high conductive crystalline Si substrate was used as an metal-like bottom gate and SiN insulating layer was then deposited by LPCVD(low pressure chemical vapour deposition). An aluminum layer was then vacuum evaporated and patterned to form a source/drain metal contact. Oxygen partial pressure and substrate temperature were varied during the ZnO PLD deposition process and their influence on the thin film properties were investigated by X-ray diffraction(XRD) and Hall-van der Pauw method. Optical transparency of the ZnO thin film was analyzed by UV-visible phometer. The resulting ZnO-TFT devices showed an on-off ration of $10^6$ and field effect mobility of 2.4-6.1 $cm^2/V{\cdot}s$.

• Journal of information and communication convergence engineering
• /
• v.1 no.3
• /
• pp.133-138
• /
• 2003

The preparation of $Al_{2}O_{3}-SiO_{2}$ thin films from less than one micron to several tens of microns in thickness had been prepared from metal alkoxide sols. Two methods, dip-withdrawal and electrophoretic deposition, were employed for thin films and sheets formation. The requirements to be satisfied by the solution for preparing uniform and strong films and by the factors affecting thickness and other properties of the films were examined. For the preparation of thin, continuous $Al_{2}O_{3}-SiO_{2}$ films, therefore, metal-organic-derived precursor solutions contained Si and Al in a chemically polymerized form has been developed and produced in a clear liquid state. In the process of applying to substrates, this liquid left a transparent, continuous film that could be converted to crystalline $Al_{2}O_{3}-SiO_{2}$ upon heating to $1000^{\circ}C$. And, a significant change of the film density took place in the crystallization process, thus leading to the strict requirements as to the film thickness, which could survive crystallization.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.957-962
• /
• 2003

The preparation of $Al_2$O$_3$-SiO$_2$ thin films from less than one micron to several tens of microns in thickness had been prepared from metal alkoxide sols. Two methods, dip-withdrawal and electrophoretic deposition, were employed for thin films and sheets formation. The requirements to be satisfied by the solution for preparing uniform and strong films and by the factors affecting thickness and other properties of the films were examined. for the preparation of thin, continuous $Al_2$O$_3$-SiO$_2$ films, therefore, metal-organic-derived precursor solutions contained Si and Al in a chemically polymerized form has been developed and produced in a clear liquid state. In the process of applying to substrates, this liquid left a transparent, continuous film that could be converted to crystalline $Al_2$O$_3$-SiO$_2$ upon heating to 100$0^{\circ}C$. And, a significant change of the film density took place in the crystallization process, thus leading to the strict requirements as to the film thickness, which could survive crystallization.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.4
• /
• pp.1-10
• /
• 1989

To investigate the influence of temperature on the TiN film, it was deposited on the STC-3 steel and Si-wafer from $TiCl_4/N_2/H_2$ gas mixture by using the radio frequency plasma assisted chemical vapor deposition. The deposition was performed at temperature of $400^{\circ}C-500^{\circ}C$. The results showed that crystalline TiN film was deposited over $480^{\circ}C$, and all specimens showed the crystalline TiN X-ray diffraction peaks after vacuum heat treatment for 3 hrs, at $1000^{\circ}C$, $10^{-5}torr$. While the film thickness was increased above $480^{\circ}C$, it was decreased under $480^{\circ}C$ as temperature increased. And the contents of titanium were increased and it of chlorine were decreased as temperature increased. Because temperature increase was attributed to the increase in the density of TiN film, surface hardness of TiN film was increased with temperature.