• 마이크로전자및패키징학회지
• /
• 제21권3호
• /
• pp.51-56
• /
• 2014

솔더조인트의 신뢰성에는 인쇄회로기판의 표면처리 특성이 많은 영향을 미치고 있다. 본 연구에서는 ENEPIG 표면처리에서 Sn-4.0wt%Ag-0.5wt%Cu (SAC405) 솔더와 Pd 촉매 처리 시간에 따른 high speed shear 에너지 및 파괴 모드를 연구하였다. 또한 Pd 촉매 처리 시간과 무전해 Ni-P 도금의 표면 거칠기 (Ra)와의 관계를 규명하였다. Pd 촉매 처리 시간이 길어질수록 Ni-P nodule의 면적은 넓어지고, Ni-P 도금의 표면 거칠기 (Ra)는 감소한다. 이러한 영향으로 질산 기상 처리한 시편의 high speed shear 평가후 quasi-brittle과 brittle 모드의 점유율은 감소한다. 이는 Pd 촉매 처리 시간의 증가가 SAC405 솔더조인트의 신뢰도를 향상시키는 역할을 한다는 것을 나타낸다.

• Earthquakes and Structures
• /
• 제17권5호
• /
• pp.511-519
• /
• 2019

The concrete gravity dam is one of the most important parts of the nation's infrastructure. Besides the benefits, the dam also has some potentially catastrophic disasters related to the life of citizens directly. During the lifetime of service, some degradations in a dam may occur as consequences of operating conditions, environmental aspects and deterioration in materials from natural causes, especially from dynamic loads. Cumulative Absolute Velocity (CAV) plays a key role to assess the operational condition of a structure under seismic hazard. In previous researches, CAV is normally used in Nuclear Power Plant (NPP) fields, but there are no particular criteria or studies that have been made on dam structure. This paper presents a method to calculate the limitation of CAV for the Bohyeonsan Dam in Korea, where the critical Peak Ground Acceleration (PGA) is estimated from twelve sets of selected earthquakes based on High Confidence of Low Probability of Failure (HCLPF). HCLPF point denotes 5% damage probability with 95% confidence level in the fragility curve, and the corresponding PGA expresses the crucial acceleration of this dam. For determining the status of the dam, a 2D finite element model is simulated by ABAQUS. At first, the dam's parameters are optimized by the Minitab tool using the method of Central Composite Design (CCD) for increasing model reliability. Then the Response Surface Methodology (RSM) is used for updating the model and the optimization is implemented from the selected model parameters. Finally, the recorded response of the concrete gravity dam is compared against the results obtained from solving the numerical model for identifying the physical condition of the structure.

• Geomechanics and Engineering
• /
• 제28권3호
• /
• pp.265-281
• /
• 2022

A set of slurry shield test system capable of cutter cutting and slurry automatic circulation is used to investigate the deformation characteristics, the evolution characteristics of support resistance and the distribution and evolution process of earth pressure during excavating and collapsing of slurry shield tunneling in circular-gravel layer. The influence of cover-span ratio on surface subsidence, support resistance and failure mode of excavation face is also discussed. Three-dimensional numerical calculations are performed to verify the reliability of the test results. The results show that, with the decrease of the supporting force of the excavation face, the surface subsidence goes through four stages: insensitivity, slow growth, rapid growth and stability. The influence of shield excavation on the axial earth pressure of the front soil is greater than that of the vertical earth pressure. When the support resistance of the excavation face decreases to the critical value, the soil in front of the excavation face collapses. The shape of the collapse is similar to that of a bucket. The ultimate support resistance increase with the increase of the cover-span ratio, however, the angle between the bottom of the collapsed body and the direction of the tunnel excavation axis when the excavation face is damaged increase first and then becomes stable. The surface settlement value and the range of settlement trough decrease with the increase of cover-span ratio. The numerical results are basically consistent with the model test results.

• Advances in concrete construction
• /
• 제9권3호
• /
• pp.235-248
• /
• 2020

Progressive collapse in a structure occurs when load bearing members are failed and the adjoining structural elements cannot resist the redistributed forces and fails subsequently, that leads to complete collapse of structure. Recently, construction using precast concrete technology is adopted increasingly because it offers many advantages like faster construction, less requirement of skilled labours at site, reduced formwork and scaffolding, massive production with reduced amount of construction waste, better quality and better surface finishing as compared to conventional reinforced concrete construction. Connections are the critical elements for any precast structure, because in past, major collapse of precast structure took place because of connection failure. In this study, behavior of four different precast wet connections with U shaped reinforcement bars provided at different locations is evaluated. Reduced 1/3^rd scale precast beam column assemblies having two span beam and three columns with removed middle column are constructed and examined by performing experiments. The response of precast connections is compared with monolithic connection, under column removal scenario. The connection region of test specimens are filled by cast-in-place micro concrete with and without polypropylene fibers. Performance of specimen is evaluated on the basis of ultimate load carrying capacity, maximum deflection at the location of removed middle column, crack formation and failure propagation. Further, Finite element (FE) analysis is carried out for validation of experimental studies and understanding the performance of structural components. Monolithic and precast beam column assemblies are modeled using non-linear Finite Element (FE) analysis based software ABAQUS. Actual experimental conditions are simulated using appropriate boundary and loading conditions. Finite Element simulation results in terms of load versus deflection are compared with that of experimental study. The nonlinear FE analysis results shows good agreement with experimental results.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.43-55
• /
• 2000

In traditional electronic packages the die and the substrate are interconnected with fine wire. Wire bonding technology is limited to bond pads around the peripheral of the die. As the demand for I/O increases, there will be limitations with wire bonding technology. Flip chip technology eliminates the need for wire bonding by redistributing the bond pads over the entire surface of the die. Instead of wires, the die is attached to the substrate utilizing a direct solder connection. Although several steps and processes are eliminated when utilizing flip chip technology, there are several new problems that must be overcome. The main issue is the mismatch in the coefficient of thermal expansion (CTE) of the silicon die and the substrate. This mismatch will cause premature solder Joint failure. This issue can be compensated for by the use of an underfill material between the die and the substrate. Underfill helps to extend the working life of the device by providing environmental protection and structural integrity. Flux residues may interfere with the flow of underfill encapsulants causing gross solder voids and premature failure of the solder connection. Furthermore, flux residues may chemically react with the underfill polymer causing a change in its mechanical and thermal properties. As flip chip packages decrease in size, cleaning becomes more challenging. While package size continues to decrease, the total number of 1/0 continue to increase. As the I/O increases, the array density of the package increases and as the array density increases, the pitch decreases. If the pitch is decreasing, the standoff is also decreasing. This paper will present the keys to successful flip chip cleaning processes. Process parameters such as time, temperature, solvency, and impingement energy required for successful cleaning will be addressed. Flip chip packages will be cleaned and subjected to JEDEC level 3 testing, followed by accelerated stress testing. The devices will then be analyzed using acoustic microscopy and the results and conclusions reported.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권3호
• /
• pp.41-50
• /
• 2012

강재의 품질향상으로 강교에 있어서 재료자체의 파괴보다는 반복하중에 의한 피로균열 문제가 더욱 중요한 요소가 되었다. 재료의 항복으로 인한 교량의 붕괴 등의 사례는 거의 보고되고 있지 않지만 용접부에 발생하는 피로균열에 대한 사례는 매우 많이 보고되고 있다. 종리브와 횡리브, 데크 플레이트로 구성된 직교이방성 강바닥판의 피로응력은 강바닥판을 구성하는 요소들의 구성 형태 및 물성과 밀접한 관련이 있다. 본 논문에서는 Pelikan-Esslinger method와 signed Von-Mises 등가응력 개념을 활용하여 직교이방성 강바닥판의 피로응력을 산정하는 방법을 제시하고, 직교이방성 강바닥판 구성요소들의 구성형태와 물성을 변화시켜 피로응력에 미치는 영향을 분석하였다. 직교이방성 강바닥판의 피로응력과 구성요소의 상관관계 경향을 분석함으로써 설계 및 유지보수 시에 더 효율적인 대안을 찾는데 도움이 될 수 있을 것이다.

• 콘크리트학회논문집
• /
• 제13권2호
• /
• pp.168-174
• /
• 2001

탄소섬유쉬트는 고강도, 경량 및 고 내구성 등의 우수한 재료적 성질을 가지고 있어 철근콘크리트 건축물의 보수 .보강재료 장범위하게 사용되어져 왔다. 탄소섬유쉬트와 콘크리트 사이의 부착강도 즉, 부착거동은 탄소섬유쉬트에 의해 보수.보강되는 철근콘크리트 부재의 보강성능을 좌우하는 매우 중요한 요소이다. 따라서, 탄소섬유쉬트와 콘크리트의 접합면에서 발생되는 부착파괴의 메카니즘은 명확히 구명될 필요가 있다. 본 연구에서는 양생온도, 콘크리트의 표면상태 및 함수율 등의 환경요소변화에 따른 탄소섬유쉬트와 콘크리트의 인발접착강도을 파악함으로써 환경요소의 영향을 평가하였으며 아울러, 탄소섬유쉬트와 콘크리트와의 부착성능을 결정하는 유효부착길이 및 평균부착응력도를 평가하였다. 연구결과, 인발접착강도에 미치는 환경요소에서 양생온도가 가장 중요한 영향인자로 나타났으며, 인장전단부착 실험으로부터 얻어진 유효부착길이 및 평균부착응력도는 각각 15 cm 및 9.78~11.88kgf/$\textrm{cm}^2$ 내외라고 사료된다.

• 한국지반공학회논문집
• /
• 제25권12호
• /
• pp.13-25
• /
• 2009

본 연구에서는 확률론적 해석에 지반의 공간적 변동성을 고려하기 위한 해석 절차를 제시하였다. 제안된 방법은 한계평형법을 이용하는 결정론적 해석방법을 지반정수의 불확실성과 공간적 변동성을 고려할 수 있도록 확률론적 사면안정 해석으로 확장한다. 개발된 방법은 랜덤유한요소해석법과 같이 미리 임계파괴면을 가정하지 않으면서도 계산시간을 단축할 수 있다는 장점이 있다. 지정된 입력 확률분포함수와 자기상관함수를 따르는 2차원의 랜덤필드를 생성하기 위하여 Karhunen-Lo$\grave{e}$ve 전개법을 사용하였으며, 생성된 랜덤필드를 이용하여 확률론적 응답을 얻기 위해 Monte Carlo 시뮬레이션을 수행하였다. 개발된 해석기법의 적용성을 검토하고 지반정수의 공간적 변화가 확률론적 안정해석에 미치는 영향을 검토하기 위해 예제해석을 수행하였으며, 해석결과는 제안된 방법이 지반물성의 공간적 변동성에 따른 다양한 사면파괴 형태를 확률론적 사면안정 해석에 효과적으로 고려할 수 있음을 보여준다.

• 소성∙가공
• /
• 제11권1호
• /
• pp.61-68
• /
• 2002

The thermal shock and thermal fatigue test has been carried out to analyze the thermal characteristics of tool steels for hot forging and the effects of mechanical properties on this study have been investigated. The resistance to thermal shock is first of all a matter of good toughness and ductility. Therefore, a proper hot-work tool steel should be characterized by high fracture strength and high temperature toughness. Based on these results, some critical temperature($T_{fracture}$) at which fracture occur can be measured to characterize the thermal resistance of the materials. During thermal fatigue tests, the thermal fatigue cracks occur because of the repetitive heating and cooling of the die surface and the thermal fatigue damage was evaluated by analyzing different number of cycles to failure. The results showed that the resistance to thermal shock and thermal fatigue were found to be favoured by high hot tensile strength and high hot hardness, and thermal resistance of SKD61 was superior to that of ESC, SKT4 and this was caused by higher mechanical properties of SKD61.

• 한국정밀공학회지
• /
• 제26권2호
• /
• pp.86-93
• /
• 2009

Elastomeric O-rings have been the most common seals due to their excellent sealing capacity, and availability in costs and sizes. One of the critical applications of O-ring seals is solid rocket motor joint seal where the operating hot gas must be sealed during the combustion. This has long been a design issue to avoid the system failure. For laterally constrained, squeezed and pressurized condition, deformed shape of O-ring was measured by computed tomography method and CCD laser sensor, compared with numerical calculations. As clearance gap changes, sealing performance had been evaluated on peak contact stresses at top, bottom and side contact surfaces. As clearance gap increases, peak contact stresses and contact widths in top and side contact surfaces increase, and the asymmetry of stress distributions is promoted due to pressure increase. It is suggested that peak stress of bottom contact surface can be approximated by simple superposition of peak ones due to squeeze and pressure. Under pressurized condition, sealing performance is dependent on not peak stresses of bottom and side contact surfaces but that of top.