• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 ITC-CSCC -2
• /
• pp.1005-1008
• /
• 2000

This paper presents a simple method to estimate short-circuit power dissipation and propagation delay for static CMOS logic circuits. Short-circuit current expression is derived by accurately interpolating peak points of actual current curves which is influenced by the gate-to-drain coupling capacitance. The macro model and its expressions estimating the delay of CMOS circuits, which is based on the current modeling expression, are also proposed after investigating the voltage waveforms at transistor output modes. It is shown through simulations that the proposed technique yields better accuracy than previous methods when signal transition time and/or load capacitance decreases, which is a characteristic of the present technological evolution.

• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1122-1132
• /
• 2019

In this paper, aiming at high-voltage applications, transformer windings schemes of multiple-output two-transistor flyback converters are investigated, which are mainly based on the stray capacitances effect. First, based on a transformer model including equivalent stray capacitors, the operational principle of the converter is presented, and the main influence of its stay capacitors is determined. Second, the windings structures of the transformer are analyzed and designed based on the stray capacitances effect. Third, the windings arrangements of the transformer are analyzed and designed through a coupling analysis of the secondary windings and a stray capacitance analysis between the primary and secondary windings. Finally, the analysis and design conclusions are verified by experimental results obtained from a 60W laboratory prototype of a multiple-output two-transistor flyback converter.

• 대한전자공학회논문지SD
• /
• 제39권3호
• /
• pp.49-60
• /
• 2002

본 논문에서는 DRAM 모듈의 전원 평면에 대한 효과적인 설계 방법을 제시하였고 그 방법은 다음과 같이 세 단계로 구성되어 있다. 1) PEEC 등가회로를 이용한 2D 전송선 구조로 전원평면의 모델링 및 해석. 2) 측정값 비교를 통한 해석 결과 검증. 3) 전원 평면의 물리적 파라미터를 이용한 설계 가이드 제시. 제시한 내용을 바탕으로 하여 DRAM 모듈에서 전원 및 접지평면 성능을 안정화를 이루기 위한 효과적인 De-coupling 커패시터의 용량과 개수를 결정하는 방법을 기술하였다 이 설계 방법론은 스트립 구조 및 do-coupling 커패시터를 갖는 DRAM 모듈에서 효과적으로 사용할 수 있다.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.318-321
• /
• 2003

In case, sensor system performs where it is difficult to access physically and it is in the poor environment, it is limited to communicate by using wire and installing power module in sensor system. In this paper, it suggests how information is obtained from telemetry sensor by means of inductive coupling without battery. Comparing with the telemetry sensor system of inductive coupling by the power supply, this system estimates the capacitance of sensor with high precision in using RLSE, not the process of modulation and demodulation. In order to activate this system, inductive model is used and in case of time variant parameter, telemetry sensor system which has got high rate in accuracy is implemented by using the forgetting factor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.892-896
• /
• 2005

In this paper, key issues of stainless steel foil substrates for display applications have been described. We studied and analyzed technical issues on substrate passivation/planarization to control surface roughness and capacitive coupling from conductive substrates. A thick (either multiple or single) passivation/planarization layer needs to be applied on the nonelectronic-grade stainless steel substrate to provide a smooth surface and electrical insulation from the conductive substrate. Especially for large size, high-resolution display applications, low k and thick passivation/planarization layers should be used for appropriate capacitive coupling. Based on our initial study, a unit area capacitance of less than $2nF/cm^2$ of passivation/planarization layers is needed for 32" HD TV OLED displays.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권6호
• /
• pp.562-568
• /
• 2013

This paper presents a design of a wireless power transfer system based on magnetic resonant coupling technology with in-band wireless communication. To increase the transmission distance and compensate for the change in the effective capacitance due to the varying distance, the proposed system used a loop antenna with a selectable capacitor array. Because the increased transmission distance enables multiple charging, we added a communication protocol operated at the same frequency band to manage a network and control power circuits. In order to achieve the efficient bandwidth in both power transfer mode and communication mode, the S-parameters of the loop antennas are adjusted by switching a series resistor. Our test results showed that the loop antenna achieved a high Q factor in power transfer mode and enough passband in communication mode.

• Journal of the Optical Society of Korea
• /
• 제11권1호
• /
• pp.1-5
• /
• 2007

We investigate the efficiency of an optical intensity modulator based on an electrically tunable $LiNbO_3$ reflection grating. Assuming a grating coupling coefficient and the waveguide propagation loss, waveguide length is varied to find its effect on the modulator slope efficiency and the device capacitance. With the low propagation loss of the $LiNbO_3$ waveguide, a very efficient optical intensity modulator can be achieved for a low frequency (${\sim}1GHz$) as long as the requirement for the grating coupling coefficient is satisfied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.126-128
• /
• 2008

This paper presents an architecture for driving multiple paralleled cold cathode fluorescent lamps (CCFLs) for back lighting applications. Multi CCFL operation and increase of brightness, the key to the architecture is a proposed capacitive coupling approach for lamp ignition. This system is consist of a flyback converter, a single inverter to drive multiple lamps and conductive floating reflector. The topology is capable of driving a number of parallel lamps with independent accurate lamp, The capacitive coupling the leakage inductance and stray capacitance creation which it used, current regulation and improving cost effectiveness with significant reduction in size and weight, compared to typical high frequency ac ballast. Experimental demonstration results for ten of parallel CCFLs with simultaneous ignition.

• Journal of electromagnetic engineering and science
• /
• 제12권2호
• /
• pp.185-188
• /
• 2012

A compact monopole antenna possessing triple resonance ($f_1$, $f_2$, $f_3$) characteristics for (USB) dongle applications is presented. The resonance characteristic $f_1$ is determined by the overall length of the antenna. The monopole antenna acts as the main radiator for $f_3$ as well as the coupling feeding structure for the parasitic resonators in $f_1$, $f_2$. The resonance characteristic $f_2$ is achieved by a combination of the capacitance formed by the coupling between the top and bottom parasitic substrate resonators and the inductance generated by a via bridging the two parasitic resonators.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.250-255
• /
• 2018

This paper presents a method for minimizing standby power consumption in wireless power transfer (WPT) system via magnetic resonance coupling (MRC) that operates at 6.78 MHz. The proposed circuit controls the required capacitance according to operational condition in order to reduce standby power consumption. Based on an impedance characteristic of the class-E power amplifier, operational principles of the proposed circuit are analyzed. Moreover, to verify the effectiveness of the proposed class-E power amplifier, an 8 W prototype for WPT system is implemented. The measured input power of the proposed class-E power amplifier at standby condition is reduced from 5.81 W to 3.53 W.