• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1066-1074
• /
• 2015

This paper presents the reverse recovery characteristic according to the change of switching states when Si diode and SiC diode are used as clamp diode and proposes a method to minimize the switching loss containing the reverse recovery loss in the neutral-point-clamped inverter at low modulation index. The previous papers introduce many multiple circuits replacing Si diode with SiC diode to reduce the switching loss. In the neutral-point-clamped inverter, the switching loss can be also reduced by replacing device in the clamp diode. However, the switching loss in IGBT is large and the reduced switching loss cannot be still neglected. It is expected that the reverse recovery effect can be infrequent and the switching loss can be considerably reduced by the proposed method. Therefore, it is also possible to operate the inverter at the higher frequency with the better system efficiency and reduce the volume, weight and cost of filters and heatsink. The effectiveness of the proposed method is verified by numerical analysis and experiment results.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1825-1828
• /
• 2008

A simple method for the fabrication of porous nano-master for antireflective surface is presented. In conventional fabrication methods for antireflective surface, coating method with low refractive index has usually been used. However, it is required to have high cost and long times for mass production. In this paper, we suggested the fabrication method of antireflective surface by the hot embossing process using the porous nano patterned master on silicon wafer fabricated by low-temperature anodic aluminum oxidation. Through multi-AAO and etching processes, nano patterned master with high aspect ratio was fabricated at the large area. Pore diameter and inter-pore distance are about 150nm and from 150 to 200nm. In order to replicate anti-reflective structure, hot embossing process was performed by varying the processing parameters such as temperature, pressure and embossing time etc. Finally, antireflective surface can be successfully obtained after etching process to remove selectively silicon layer of AAO master.

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1244-1255
• /
• 2017

The space vector pulse width modulation (SVPWM) technique is a popular PWM method for medium voltage drive applications. Conventional SVPWM (CSVPWM) and bus clamped SVPWM (BCSVPWM) are the most common SVPWM techniques. This paper evaluates the performance of various advanced BCSVPWM strategies in terms of their harmonic distortion and switching loss based on a uniform frame work. A uniform frame work, pulse number captures the performance parameter variations of different SVPWM strategies for various number of samples with heterogeneous pulse numbers. This work compares different advanced BCSVPWM techniques based on the modulation index and location of the clamping position (zero vector changing angle ) of a phase in a line cycle. The frame work provides a fixed fundamental frequency of 50Hz. The different BCSVPWM switching strategies are implemented and compared experimentally on a 415V, 2.2kW, 50Hz, 3-phase induction motor drive which is fed from an IGBT based 2 KVA voltage source inverter (VSI) with a DC bus voltage of 400 V. A low cost PIC microcontroller (PIC18F452) is used as the controller platform.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.11 no.1
• /
• pp.45-49
• /
• 1982

This study aims to substitute the emulsifier and gelifier for the poly phosphates with regard to diminishing the foreign phosphates in diet and production cost. It is desirable to introduce the application of theory for melting phenomenon in this investigation since the rate of peptisation is very representative index during the conversion of Ca-paracaseinate to Na-paracaseinate in processed cheese. It will be impossible to substitute completely for polyphosphates but partial substitution could be possible if one consider the organoleptic quality of typical processed cheese.

• Management Science and Financial Engineering
• /
• v.11 no.3
• /
• pp.79-93
• /
• 2005

Despite the fact that the sourcing process in B2B e-Marketplaces is one of the most important tasks, the evaluation and selection process of suppliers have been ad-hoc based and mainly dependent on the experience of sourcing managers' subjective knowledge. To remedy the problem, we developed a decision support System (called Wise - I) that helps sourcing managers evaluate suppliers in a more systematic way. The system reflects company's strategy and know-how by adopting company enforced weighted scores for different factors and employing a more scientific method of considering factors other than price and on-time delivery rate, utilizing the AHP method. This paper reports the effectiveness of the system as well as the detailed description of the system. To investigate the effectiveness of the system, we collected information through interview and questionnaire survey. The information was also augmented through the firm key index system, which monitors average delivery lead time and on-time delivery rate. The result indicates that the system leads to the efficiency of purchasing section and the transparency of buying process, therefore reduces delivery time and cost.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.2
• /
• pp.137-144
• /
• 1995

The I.A.P.(Index of Atmospheric Purity) by the distribution of Bryophtes on the bark of various latifoliate tree trunks was investigated at four sites(Daeheung, Songkwang, Jeungsim, and Heunggook Temple) from April, 1991 to April, 1993. The IAP was in inverse proportion to the degree of air pollution. The I.A.P at four sites were estimated 78.2 at Daeheung temple, 61.0 at Songkwang temple, 28.3 at Jeungsim temple, and 10.3 at Heunggook temple, respectively. The distribution degree of Bryophytes in Heunggook temple progressed during the last ten years. It represents the bettrment of air quality. Bioassay by means of lichens seems to have great potential for better and less expensive ways of measuring pollution levels instead of the high cost of buying and maintaining air pollution monitoring equipment.

• Korean Journal of Environmental Biology
• /
• v.32 no.2
• /
• pp.102-111
• /
• 2014

Ecological restoration is regarded as a major strategy for preventing biodiversity loss and thereby enhancing ecosystem service. This study was performed to evaluate ecosystem service value that the restored ecosystem provides. Ecosystem service was evaluated for provisioning and regulating services. The former service was evaluated by comparing similarities in a viewpoint of floristic composition to the reference site between the restored and the unrestored sites. Species composition of the restored site was found to be more similar to the reference site than that of the unrestored site and thereby restoration practice contributed for enhancing the provisioning service. Regulating service was evaluated based on microclimate control, soil amelioration, and improvement of water holding capacity. The value of ecosystem services in terms of microclimate control, soil amelioration, and improvement of water holding capacity was higher in the restored site than in the unrestored site. In consequence, ecological restoration of coal mine spoils contributed for enhancing the ecosystem service value of the corresponding site and thereby is rewarding the cost invested for restoration.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.341-344
• /
• 2007

A major obstacle to classify and validate Land Cover maps is the high cost of generating reference data or multiple thematic maps for subsequent comparative analysis. In case of inaccessible area such as North Korea, the high resolution satellite imagery may be used as in situ data so as to overcome the lack of reliable reference data. The objective of this paper is to investigate the possibility of utilizing QuickBird (0.6m) of North Korea obtained from Google Earth data provided thru internet. Monthly NDVI images of nine months from the summer of 2004 were classified into L=54 cluster using ISODATA algorithm, and these L clusters were assigned to 7 classes; coniferous forest, deciduous forest, mixed forest, paddy field, dry field, water and built-up area. The overall accuracy and Kappa index were 85.98% and 0.82, respectively, which represents about 10% point increase of classification accuracy than our previous study based on GCP point data around North Korea. Thus we can conclude that Google Earth may be used to substitute the traditional in situ data collection on the site where the accessibility is severely limited.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.3
• /
• pp.64-70
• /
• 2007

Of all the rapid tooling (RT) methods currently available, thick-layer laminated tooling is the most suitable for large-scale, low-cost dies and molds. Currently, the determination of a lamina's contour or profile and the associated slicing algorithms are based on existing rapid prototyping (RP) data manipulation technology. This paper presents a new adaptive slicing algorithm developed exclusively for profiled edge laminae (PEL) tooling PEL tooling is a thick-layer RT technique that involves the assembly of an array of laminae, whose top edges are simultaneously profiled and beveled using a line-of-sight cutting method based on a CAD model of the intended tool surface. The cutting profiles are based on the intersection curve obtained directly from the CAD model to ensure geometrical accuracy. The slicing algorithm determines the lamina thicknesses that minimize the dimensional error using a new tool shape error index. At the same time, the algorithm considers the available lamination thicknesses and desired lamina interface locations. We demonstrate the new slicing algorithm by developing a simple industrial PEL tool based on a CAD part shape.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.3
• /
• pp.81-87
• /
• 2014

Conditions of paper manufacturing process should be changed depending on the end use and paper properties. Most of the case, mixed pulps with long softwood fibers and short hardwood fibers are used to achieve proper qualities of product with reasonable production cost. For specialty paper manufacture the wood pulp and cotton linter pulp are usually mixed together. The objectives of this study is to analyze physical, mechanical and fracture mechanical properties of paper depending on SwBKP, HwBKP and cotton linter pulp(CLP) mixing. When the mixing ratio of SwBKP was increased, strength properties, such as tensile, tear, and folding endurance, were also increased. When the mixing ratio of SwBKP and HwBKP was increased, stress concentration index was decreased and fracture toughness was increased.