• Resources Recycling
• /
• v.31 no.1
• /
• pp.12-20
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys containing Co, Cu, Fe, Mn, Ni, and Si. A process to separate metal ions from the sulfuric acid leaching solution of these metallic alloys has been reported. In this process, ionic liquids are employed to separate Fe(III) and Cu(II). In this study, D2EHPA and Cyanex 301 were employed to replace these ionic liquids. Fe(III) and Cu(II) from the sulfate solution were sequentially extracted using 0.5 M D2EHPA with three stages of cross-current and 0.3 M Cyanex 301. The stripping of Fe(III) and Cu(II) from the loaded phases was performed using 50% (v/v) and 60% (v/v) aqua regia solutions, respectively. The mass balance results from this process indicated that the recovery and purity percentages of the metals were greater than 99%.

• Nuclear Engineering and Technology
• /
• v.54 no.10
• /
• pp.3855-3863
• /
• 2022

An evaluation of the radiation shielding performance of high-Z-particle-loaded polylactic acid (PLA) composite materials was pursued. Specimens were produced via fused deposition modeling (FDM) using copper-PLA, steel-PLA, and BaSO₄-PLA composite filaments containing 82.7, 75.2, and 44.6 wt% particulate phase contents, respectively, and were tested under broad-band flash x-ray conditions at the Sandia National Laboratories HERMES III facility. The experimental results for the mass attenuation coefficients of the composites were found to be in good agreement with GEANT4 simulations carried out using the same exposure conditions and an atomistic mixture as a model for the composite materials. Further simulation studies, focusing on the Cu-PLA composite system, were used to explore a shield design parameter space (in this case, defined by Cu-particle loading and shield areal density) to assess performance under both high-energy photon and electron fluxes over an incident energy range of 0.5-15 MeV. Based on these results, a method is proposed that can assist in the visualization and isolation of shield parameter coordinate sets that optimize performance under targeted radiation characteristics (type, energy). For electron flux shielding, an empirical relationship was found between areal density (AD), electron energy (E), composition and performance. In cases where ${\frac{E}{AD}}{\geq}2MeV{\bullet}cm{\bullet}g^{-1}$, a shield composed of >85 wt% Cu results in optimal performance. In contrast, a shield composed of <10 wt% Cu is anticipated to perform best against electron irradiation when ${\frac{E}{AD}}<2MeV{\bullet}cm{\bullet}g^{-1}$.

• The Korea Journal of Herbology
• /
• v.35 no.2
• /
• pp.1-6
• /
• 2020

Objectives : Heating process is the traditional processing method that has been applied to reduce the toxicity of dried resin of Toxicodendron vernicifluum (Anacardiacea) used as Geon-chil (乾漆, Lacca Rhois Exsiccata or Toxicodendri Resina). Urushiol, which is found in the plants of Toxicodendron genus, is a toxic compound that is absorbed into the skin and induces allergic dermatitis by being contacted. Hence, the reduction of urushiol level by heating processing of Geon-chil is crucial method for its medicinal application. Methods : Due to lack of Geon-chil processing-related articles, the articles researching the processing of lacquer (漆), as a coating material, were collected and analyzed to investigate the chemical change of urushiol during heating process. Results : The results demonstrate that the resin which was collected from the sap of T. vernicifluum tree was dried under warm and humid conditions repeatedly. During primary drying process, the laccase, a copper-containing enzyme in the resin, participated in the formation of urushiol polymers and thereafter urushiol-related toxicity could be reduced by making a lacquer harder and more stable. Moreover, heating a lacquer over 200℃ could cause thermo-degradation of urushiol polymers, and vaporized thermally degraded urushiol monomers and their by-products, which were determined using pyrolysis/GC-MS. Conclusions : These results support that heating process being performed over 200 ℃, such as stir-frying (炒) or calcination (煅), reduces the urushiol content in Geon-chil and hence, its medicinal use can be more stable without urushiol-related allergic reactions.

• Korean Journal of Soil Science and Fertilizer
• /
• v.19 no.4
• /
• pp.307-314
• /
• 1986

Cu(II) binding mechanisms with water soluble organic fractions (WSOF) extracted from an agricultural soil (W), a soil treated with sludge for 6 years ($WS_6$), a sludge-soil mixture incubated for one week ($WS_1$), and sewage sludge (SS) were studied by electron spin resonance (ESR) spectroscopy and potentiometric titrations. Cu(II)-WSOF complexes produced $g_{11}$ values which were larger than $g_{\perp}$ values, indicating that the coordination of Cu(II) complex was an elongated octahedron. At liquid $N_2$ temperature (77K), the Cu(II)-W complex showed an anisotropic ESR spectrum while the Cu(II)-SS complex showed an isotropic spectrum. These spectral results suggest that the oxygen donor ligands of W may form relatively strong bonds with $Cu^{2+}$ due to extensive chelation while ligands of SS may form little or no chelate bonds with $Cu^{2+}$. The ESR spectra of Cu(II)-SS complex also suggest that each of four in-plane ligands (e.g., $COO^-$, $H_2O$, $Cl^-$, etc.) may act independently as monodentate ligands. Oxygen donor ligands such as aromatic carboxyl groups were probably the major Cu(II) binding sites in W. Sulfonate, aliphatic carboxyl group, and N-containing ligands were probably the major binding sites in SS at pH 5. The Cu(II) complexation with N-containing groups increased as sludge was added to the soil. Much higher (6x) pyridine concentrations were required to displace W from Cu(II)-W complex as compared to the Cu(II)-SS complex.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.7
• /
• pp.729-734
• /
• 2008

The higher valence state of iron i.e., Fe(VI) was employed for the treatment of Cu(II)-EDTA in the aqueous/waste waters. The ferrate(VI) was prepared through wet oxidation of Fe(III) by sodium hypochlorite. The purity of prepared Fe(VI) was above 93%. The stability of Fe(VI) solution decreased as solution pH decreased through self decomposition. The reduction of Fe(VI) was obtained by using the UV-Visible measurements. The dissociation of Cu(II)-EDTA complex through oxidation of EDTA using Fe(VI) and subsequent treatment of organic matter and metal ions by Fe(III) reduced from Fe(VI) in bench-scale of continuous flow reactor were studied. The removal efficiencies of copper were 69% and 79% in pH control basin and reactor, respectively, at 120 minutes as retention time. In addition, Cu(II)-EDTA in the reactor was decomplexated more than 80% after 120 minutes as retention time. From this work, a continuous treatment process for the wastewater containing metal and EDTA by employing Fe(VI) as muluti-functional agent was developed.

• Journal of Environmental Health Sciences
• /
• v.43 no.2
• /
• pp.103-110
• /
• 2017

Objectives: This study was performed to provide basic data for the re-establishment of standards (criteria) and analytical methods for hazardous metals in nail enamel. Methods: Ten metals (lead; Pb, arsenic; As, cadminum; Cd, antimony: Sb, cobalt; Co, nikel; Ni, copper; Cu, chromium; Cr, aluminum; Al, and mercury; Hg) were measured in 67 commercial nail enamels containing glitter and/or pearls. The content of hazardous metals (excepting Hg) was determined by using an inductively coupled plasma-optical emission spectrophotometer (ICP-OES) after microwave digestion. Mercury content was measured by a mercury analyzer without any preparation. Results: The detected ranges of the intact samples were as follows: $ND-1.756{\mu}g/g$ for Pb, $ND-1.24{\mu}g/g$ for As, ND for Cd, $ND-20.41{\mu}g/g$ for Sb, $ND-12.36{\mu}g/g$ for Co, $ND-7.908{\mu}g/g$ for Ni, $0.088-79.27{\mu}g/g$ for Cu, $0.281-18.54{\mu}g/g$ for Cr, $13.78-3563{\mu}g/g$ for Al, and $ND-0.044{\mu}g/g$ for Hg. After centrifugation, the detected ranges of supernatant were as follows: $ND-0.435{\mu}g/g$ for Pb, $ND-0.504{\mu}g/g$ for As, ND for Cd, $ND-0.035{\mu}g/g$ for Sb, $ND-13.17{\mu}g/g$ for Co, $ND-0.232{\mu}g/g$ for Ni, $0.117-90.07{\mu}g/g$ for Cu, $0.174-2.787{\mu}g/g$ for Cr, and $9.459-1565{\mu}g/g$ for Al. The results of this analysis showed that the levels of heavy metals such as Pb, As, and Sb were much higher in the intact samples than those of supernatant. Conclusion: In the present study, we found that the levels of hazardous metals were significantly different depending on the status of the presence of glitter. Based on the results, we recommend that the product consumer refrain from prolonged application of nail enamel, avoid biting or chewing the nails, and wear gloves during cooking and washing dishes.

• Korean Journal of Microbiology
• /
• v.50 no.3
• /
• pp.179-184
• /
• 2014

Mitigation of heavy metal toxicity by iron containing superoxide dismutase (FeSOD) of Streptomyces subrutilus P5 was investigated. For E. coli $DH5{\alpha}$, the survival rate in the presence of 0.1 mM lead ions was only 7% after 120 min; however, with the addition of $0.1{\mu}M$ of purified native FeSOD the survival rate increased to 39%. This detoxification effect was also shown with 0.01 mM copper ions (survival increased from 6% to 50%), and the effect was stronger than with the use of EDTA. E. coli M15[pREP4] producing 6xHis-tagged FeSOD was constructed, and this showed an increase in survival rates throughout the incubation time; in the presence of 0.1 mM lead ions,the final increase at 60 min was from 3% to 19%. The FeSOD absorbed about 123 g-atom lead per subunit; therefore, we suggest that FeSOD could sequestrate toxic heavy metals to enhance bacterial survival against heavy metal contamination.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.474-481
• /
• 2018

The policy-making and technological development of eco-friendly automobiles designed to increase their supply is ongoing, but the internal combustion engine still accounts for approximately 95% of automobiles in use. To meet the stricter emission regulations of internal combustion engines based on fossil fuels, the proportion of after-treatments for vehicles and (ocean going) vessels is increasing continuously. As diesel engines have high power and good fuel economy in addition to less CO2 emissions, their market share is increasing not only in commercial vehicles, but also in passenger cars. Because of the characteristics of the diesel combustion, however, NOx is generated in localized high-temperature combustion regions, and particulates are formed in the zones of diffusion combustion. LNT and urea-SCR catalysts have been developed for the after-treatment of exhaust gas to reduce NOx in diesel vehicles. This study examined the effect of a containing promoter on SCR catalysts to cope with the severe exhaust gas regulation. The de-NOx performance of the Mn-SCR catalyst was the best, and the de-NOx performance was improved as the ion exchange rate between Mn ion and Zeolyst was good and the activation energy was low. The de-NOx performance of the 7Cu-15Ba/78Zeoyst catalyst was 32% at $200^{\circ}C$ and 30% at $500^{\circ}C$, and showed the highest performance. The NOx storage material of BaO loaded as a promoter was well dispersed in the Cu-SCR catalyst and the additional de-NOx performance of BaO was affected by the reduction reaction of the Cu-SCR catalyst. Among the three catalysts, the 7Cu-15Ba/Zeolyst SCR catalyst was resistant to thermal degradation. The same type of CuO due to thermal degradation migrates and agglomerates because BaO reduces the agglomeration of the main catalyst CuO particles.

• Horticultural Science & Technology
• /
• v.35 no.3
• /
• pp.289-299
• /
• 2017

The objective of this study was to determine the effect of replacing perlite (PL) with pellets processed with poultry feather fiber as an inert material to prepare growing medium. The growth and flowering of Salvia splendens 'Vista Red' grown in individual growing medium $Biosangto^{(R)}$, peat moss (PM), PL, and two pellets (P45-1 and P45-2) were evaluated. Peat moss was mixed with PL, P45-1, or P45-2 at various ratios (1:0 to 1:3 or 3:1 by volume) to investigate the feasibility of replacing PL with pellets. Nutrient composition of the growing medium and leaf tissues was analyzed. The number of florets, inflorescence length, plant height, and fresh weight of plants grown in media containing P45-1 or P45-2 were reduced compared to those grown in individual growing medium PM or PL. As the mixing ratio of P45-1 or P45-2 to PM was higher, the growth of salvia, such as inflorescence length, plant height, number of leaves, and fresh weight was inhibited. Our results indicate that mixing three parts PM with one part of P45-1 (PM/P45-1/3:1) or P45-2 (PM/P45-2/3:1) accelerated flowering and increased the number of florets and leaves compared to other mixing ratios of PM and pellets media. The concentrations of phosphorus (P), calcium (Ca), boron (B), iron (Fe), and copper (Cu) in individual growing medium PL, P45-1, and P45-2 were significantly lower than those in PM. The concentration of N was the highest in leaves of plants grown in P45-1 or P45-2 amended media, and the concentrations of P, Ca, and zinc (Zn) in leaves were lower in individual growing medium P45-1 or P45-2 than in PM and PL. The pH of PM/P45-1/3:1 or PM/P45-2/3:1 media was maintained at optimal level (5.8-5.9) and the concentrations of macro- and micro-elements in the media and leaves were considered to be optimal levels. Therefore, mixing three parts PM with one part P45-1(PM:P45-1/3:1) or P45-2 (PM:P45-2/3:1) is recommended for improved growth and flowering in salvia. This suggests that P45-1 or P45-2 can replace PL as an inert material to prepare growing medium.

• Korean Journal of Poultry Science
• /
• v.36 no.2
• /
• pp.103-110
• /
• 2009

This experiment was conducted using 350 Lohmann Brown layers (67 weeks of age) to evaluate the dietary effect of organic or inorganic Se and Cu on their contents in chicken eggs. The layers were divided into seven groups and fed a commercial diet or one of the six experimental diets containing different levels of Se and Cu (T1, 0.3ppm organic Se; T2, 1.0ppm organic Se; T3, 1.0ppm inorganic Se; T4, 125ppm organic Cu; T5, 250ppm organic Cu; and T6, 250ppm inorganic Cu) for 5 weeks. No significant differences were observed in egg production and its qualities among groups. The contents of blood cholesterol in the birds fed various levels of Se and Cu were not significantly different as compared to control. Se contents in eggs were linearly increased as dietary Se levels increased for both sources, but Se contents from the groups fed organic Se were slightly higher than those fed inorganic Se. Sensory characteristics of eggs were not influenced by dietary treatments. In conclusion, Se contents in eggs were linearly increased as dietary levels of organic or inorganic Se increased, but eggs in layers fed the diet containing organic Se did not show higher Se contents than those in birds fed dietary inorganic Se.