• 대한기계학회논문집B
• /
• 제20권3호
• /
• pp.1015-1027
• /
• 1996

In this paper, a numerical procedure for the calculation of the incompressible Navier-Stokes equations in a generalized nonorthogonal body fitted coordinate system is proposed and is validated through three test problems. Present numerical procedure derives the pressure equation by using the pressure substitution method on the regular grid system, and discretized momentum equations are based on the covariant velocity components. Cavity flow, backward facing step flow, and two dimensional channel flow with a sinusoidal wavy wall are chosen as three test problems. Numerical solutions obtained by present procedure shows a good agreement with previous numerical and/or experimental results. Convergence rate is also satisfactory.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권1호
• /
• pp.28-31
• /
• 2010

A magnetic field calculation method for toroidal type winding which has circular section was developed. At first, the equation for magnetic field by single filament coil was extended using numerical integration to estimate the entire interesting region of solenoid, especially winding region itself. And then, the magnetic field by toroidal arrangement of solenoids was computed with a coordinate transformation of vector fields. The superconducting magnet with toroidal arrangement can be made up of several tens of solenoid type double pancake windings for some applications such as superconducting magnetic energy storage system(SMES). In this system, the field calculation on the high-Tc superconducting(HTS) tape itself is very important because the entire system can be reached to a fault by magnetic stress of conductor or the critical current of superconducting tape can be dramatically reduced under its self field condition. To make matters worse, 3-dimensional analysis is indispensable for this type of magnet and the most of commercial programs with finite element method can be taken too much time for analysis and design. In this paper, a magnetic field calculation method for toroidal type winding with circular section was induced.

• 한국소음진동공학회논문집
• /
• 제16권6호
• /
• pp.643-650
• /
• 2006

This paper is concerned with the vibration analysis of a simply-supported rectangular plate with a circular cutout. Even though there have been many methods developed for the free vibration of the rectangular plate with a rectangular cutout, very few research has been carried out for the rectangular plate with a circular cutout. In this paper, a new methodology called independent coordinate coupling method, which was developed to save the computational effort for the free vibration analysis of rectangular plate with a rectangular cutout, is applied to the case of circular cutout. The independent coordinate coupling method employs the global coordinate system for the plate and the local coordinate system for the cutout. In the case of the rectangular plate with a circular cutout, the global coordinate system is the Cartesian coordinate system and the local coordinate system is the polar coordinate system. By imposing the compatibility condition, the relationship between the global coordinates and the local coordinates is derived. This equation is then used for the calculation of the mass and stiffness matrices resulting in eigenvalue problem. The numerical results show the efficacy of the proposed method.

• 대한기계학회논문집B
• /
• 제28권4호
• /
• pp.433-440
• /
• 2004

Since the numerical analysis was adopted in the mold design, lots of computational methods have been proposed for the simulations of casting processes for the various shaped molds. Today, it is possible to simulate the filling and solidification processes of most casts using the VOF technique. Though the three-dimensional numerical model based on the Cartesian coordinate system can be applied to any shape of cast, it becomes very inefficient when the three-dimensional model is applied to the cast of axi-symmetrical shape since the control volume includes at least 11 of the physical model. In addition, the more meshes should be distributed along the circumferential boundaries of curved shape in the Cartesian coordinate system fur the better results, while such curved circumferential boundary does not need to be considered in the two-dimensional cylindrical coordinate system. This motivates the present study i.e. developing a two-dimensional numerical model for the axi-symmetrically shaped casts. The SIMPLER algorithm, the VOF method, and the equivalent specific heat method have been adopted in the combined algorithm for the flow calculation, the free surface tracking, and the phase change heat transfer, respectively. The numerical model has been applied to the casting process of a pulley, and it was proven that the mesh and time effective calculation was accomplished comparing to the calculation using three-dimensional model.

• 대한공간정보학회지
• /
• 제19권4호
• /
• pp.127-138
• /
• 2011

본 연구에서는 지적기준점과 도시기준점을 연계 활용의 가능성을 제시하고자 창원시를 대상으로 세계측지계 성과로 고시된 창원시 도시기준점(32점)의 GPS 관측데이터를 이용하여 도시기준점에 대한 지적좌표 성과를 산출 분석하여 보았다. 연구결과 3가지 서로 다른 계산 S/W를 이용해 지적좌표를 산출하고 이를 기존 도시기준점 고시 성과와 비교한 결과 현행 법률에서 규정하고 있는 오차의 허용범위 이내로 분석되어 지적측량에 활용 가능성이 있는 것으로 나타났다. 다만 실무에서 안정적인 활용 위해 현행 도시기준점 고시 성과를 직접 지적측량에 이용하기 보다는 새로이 지적성과를 산출해서 활용하는 방안을 제안하였다. 또한 지역 삼각점에 대한 사전 정밀한 성과점검이 필요함을 제시하였다. 끝으로 계산 S/W는 삼변망조정계산 S/W가 적합한 것으로 나타났다.

• 한국군사과학기술학회지
• /
• 제11권6호
• /
• pp.63-73
• /
• 2008

The helicopter position, heading data and the direction finding data of ESM are essentially required to compensate the parallax and analyze the direction finding accuracy of heliborne ESM in flight test phase. In the case of the long test range compared with small platform like as LYNX helicopter and Jisim Island test site, the parallax compensation for direction finding accuracy calculation and GPS position error can be neglected. In this paper, the direction finding accuracy on the basis of helicopter propeller was calculated by coordinate changing between helicopter and transmitting antenna from WGS84 coordinate to navigation coordinate using helicopter position and direction finding data.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1177-1182
• /
• 2006

This paper is concerned with the vibration analysis of a simply-supported rectangular plate with a circular cutout. Even though there have be en many methods developed for the free vibration of the rectangular plate with a rectangular cutout., very few research has been carried out for the rectangular plate with a circular cutout. In this paper, a new methodology called independent coordinate coupling method, which was developed to save the computational effort for the free vibration analysis of rectangular plate with a rectangular cutout, is applied to the case of circular cutout. The independent coordinate coupling method employs the global coordinate system for the plate and the local coordinate system for the cutout. In the case of the rectangular plate with a circular cutout, the global coordinate system is the Cartesian co ordinate system and the local coordinate system is the polar coordinate system. By imposing the compatibility condition, the relationship between the global coordinates and the local coordinates is derived. This equation is then used for the calculation of the mass and stiffness matrices resulting in eigenvalue problem. The numerical results show the efficacy of the proposed method.

• 한국해안해양공학회지
• /
• 제10권3호
• /
• pp.125-131
• /
• 1998

본 논문은 경계처리 및 계산과정에 있어서 좀더 개선된 파랑 예측이 보장되도록 기존의 정방형 좌표계에서 수립된 포물선형 및 쌍곡선형 파랑 모델을 경계고정좌표계에 적용하였다. 일정 수심의 만곡 수로를 따라 진행 및 반사하는 파랑에 대한 이론해와 비교하여 수치 모델 결과는 모두 만족할만하였다. 포물선형 모델의 반사 파랑 모의는 반사물에 접근한 입사파를 다시 외해 경계 쪽으로 역계산하여 수행된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.967-972
• /
• 2008

This paper presents the free vibration analysis of a circular plate with a concentric square hole. The present problem deals with the numerical calculation of the natural frequencies and mode shapes of vibration of the structure by means of Independent Coordinate Coupling Method (ICCM). In this study, the boundary condition is the edge of the square hole is free and the outer circular plate is simply supported. Due to the geometric abnormality, this analysis does not permit an exact solution. Since the ICCM employs coordinate systems corresponding to each domain independently, the kinetic and potential energy expressions necessary for the Rayleigh-Ritz method can be easily obtained. Lastly, the kinematic relation is imposed. In this way, the eigenvalue problem can be easily set up. The numerical results show the efficacy of the ICCM and changes in natural frequencies and modes due to the square hole size.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1128-1131
• /
• 1996

The collision-free path planning presented here uses linear parametric curve with one intermediate connection point between start and target points. The algorithm, in which connection point is organized in elliptic chord.(.theta., .delta.), maps objects in Euclidean Space into images in CPS through intersection check between path and obstacles a process defined as GM. Elliptic locus has special property that the total distance between focus points through a point on ellipse is the same regardless of .theta.. Hence by locating the start and target points to focus points of ellipse, and organizing connection point in elliptic coordinate, the .delta.-axis of CPS represents length of path. The GM of EWS requires calculation of interference in circumferential direction only. The procedures for GM is developed which include categorization of obstacles to reduce calculation amount. Simulations of GM of EWS, on a PC with Pentium/90MHz, is carried out to measure performance of algorithm and the results are reported on a table. The simulations are done for number of cases with different number of obstacles and location of start/target points.