• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1161-1167
• /
• 2004

The conventional PLL(phase locked loop) frequency synthesizer takes a long switching time because of the inherent closed-loop structure. The digital hybrid PLL(DH-PLL) which includes the open-loop structure into the conventional PLL synthesizer has been studied to overcome this demerit. It operates in high speed, but the hardware complexity and power consumption are the serious problem because the DLT(digital look-up table) is usually implemented by the ROM which contains the transfer characteristic of VCO(voltage controlled oscillator). This paper proposes a new DH-PLL using a very simple DLT-replacement digital logic instead of the complex ROM-type DLT. Also, a timing synchronization circuit for the very small over-shoot and shorter settling time is designed for the ultra fast switching speed at every frequency synthesis. The hardware complexity gets decreased to about $28\%,$ as compared with the conventional DH-PLL. The high speed switching characteristic of the frequency synthesis process can be verified by the computer simulation and the circuit implementation.

• Molecules and Cells
• /
• v.37 no.2
• /
• pp.161-171
• /
• 2014

In several lysosomal storage disorders, including Niemann-Pick disease Type C (NP-C), sphingolipids, including glycosphingolipids, particularly gangliosides, are the predominant storage materials in the brain, raising the possibility that accumulation of these lipids may be involved in the NP-C neurodegenerative process. However, correlation of these accumulations and NP-C neuropathology has not been fully characterized. Here we derived NP-C mice with complete and partial deletion of the Siat9 (encoding GM3 synthase) gene in order to investigate the role of ganglioside in NP-C pathogenesis. According to our results, NP-C mice with homozygotic deletion of GM3 synthase exhibited an enhanced neuropathological phenotype and died significantly earlier than NP-C mice. Notably, in contrast to complete depletion, NP-C mice with partial deletion of the GM3 synthase gene showed ameliorated NP-C neuropathology, including motor disability, demyelination, and abnormal accumulation of cholesterol and sphingolipids. These findings indicate the crucial role of GM3 synthesis in the NP-C phenotype and progression of CNS pathologic abnormality, suggesting that well-controlled inhibition of GM3 synthesis could be used as a therapeutic strategy.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.5
• /
• pp.101-106
• /
• 2011

In this paper, our goal is to design the controller which operates a manufacturing system, discrete event system, guaranteeing user specification. In specially, based on supervisory control theory W. M. Wonham, our work consists in performing the controller using Petri nets possible parallelism. In addition, we consider the problem of allocation for resources sharing of the issues to consider when designing using Petri net. The controller can be generated by synthesis of user specification model and plant model after giving the management for the resource sharing. This created controller can control the deadlock and starvation which can occur in the case with resource sharing. Previous studies proposed the Constrained Synchronous Reachability graph to synthesis of the two Petri nets models. Therefore, we provide the controlled system which forbids a deadlock and starvation using the result of previous studies.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.233-243
• /
• 2013

The inorganic pearlescent pigment have high physical and chemical stability, thus it is used in a variety field, which has better light stability, solvent resistance and thermostability. In this paper, we were synthesized the pearlescent pigment for cosmetics which was coated cobalt chloride for base of blue color metal oxide on mica titania substrate using hydrothermal synthesis method. To complement the color of the pigment by cobalt, pearl pigment were coated by different metal salt and cobalt ratio, to implement a variety of color value, depending on the kind of metal salts were synthesized. Synthesized pearlescent pigments appear various color as kind of added metal salt precursor and molar ration of cobalt and other metals. We controlled coating and color by composition of metal salt and type of metal salts, and that confirm the pigment characteristics of color changes through the analysis of color difference meter. Synthesized pigment was characterized by SPM, SEM, XRD, and EDS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.361.2-361.2
• /
• 2014

Transition metal dichalcogenides (MoS2, WS2, WSe2, MoSe2, NbS2, NbSe2, etc.) are layered materials that can exhibit semiconducting, metallic and even superconducting behavior. In the bulk form, the semiconducting phases (MoS2, WS2, WSe2, MoSe2) have an indirect band gap. Recently, these layered systems have attracted a great deal of attention mainly due to their complementary electronic properties when compared to other two-dimensional materials, such as graphene (a semimetal) and boron nitride (an insulator). However, these bulk properties could be significantly modified when the system becomes mono-layered; the indirect band gap becomes direct. Such changes in the band structure when reducing the thickness of a WS2 film have important implications for the development of novel applications, such as valleytronics. In this work, we report for the controlled synthesis of large-area (~cm2) single-, bi-, and few-layer WS2 using a two-step process. WOx thin films were deposited onto a Si/SiO2 substrate, and these films were then sulfurized under vacuum in a second step occurring at high temperatures ($750^{\circ}C$). Furthermore, we have developed an efficient route to transfer these WS2 films onto different substrates, using concentrated HF. WS2 films of different thicknesses have been analyzed by optical microscopy, Raman spectroscopy, and high-resolution transmission electron microscopy.

• Polymer(Korea)
• /
• v.24 no.1
• /
• pp.133-139
• /
• 2000

Poly(ethylene glycol) with number-average molecular weight (M$_{n}$) of 200 (PEG 200) or 400 (PEG 400) was reacted with various linking agents (CH$_2$Cl$_2$, CH$_2$Br$_2$, CH$_2$I$_2$, Br(CH$_2$)$_3$Br) in the presence of alkali to form of oxyalkylene linked chains. Molecular weights of copolymers were controlled using feed mole ratio of alkali/CH$_2$C1$_2$/PEG. The M$_{n}$ of the polymers measured by end group analysis and that measured by GPC agreed well. Molecuglar weights of polyether copolymers obtained from PEG 200 and PEG 400 were about 500~8500 and 1000~2000, respectively. Polyether copolymers prepared from PEG 400 showed melting points of around 1$0^{\circ}C$. Glass transition temperatures of the copolymers were around -75$^{\circ}C$ and the crystallinity was about 0~25%. The polyether copolymers prepared from PEG 200 had no crystallinity below the M$_{n}$ of 2500. 2500.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.987-992
• /
• 1998

Titanium aluminide intermetallic compound was formed from high purity elemental Ti and A1 foils by selfpropagating, high-temperature synthesis(SHS1 in hot press. Formation of $TiAl_3$ intermetallics at the interface between Ti and Al foil was observed to be controlled by temperature, pressure and heating rate. Especially, the heating rate is the most important role to form intermetallic compound by SHS reaction. According to DTA experiment, the SHS reactions appeared at two different temperatures below and above the melting point of Al. It was also observed that both SHS reaction temperatures increased with increasing the heating rate. After the SHS reaction of alternatively layered 10 Ti and 9 A1 foils at the heating rate of $20^{\circ}C$/min, the $700\mu\textrm{m}$ thick titanium aluminide sheet was formed by heat treatment at $810^{\circ}C$ for 4hours.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1072-1079
• /
• 2005

Conceptual design is the first step in the overall process of product design. Its intrinsic uncertainty, imprecision, and lack of information lead to the fact that current conceptual design activities in engineering have not been computerized and very few CAD systems are available to support conceptual design. In most of the current intelligent design systems, approach of principle synthesis, such as morphology matrix, bond graphic, or design catalogues, is usually adopted to deal with the concept generation, in which optional concepts are generally combined and enumerated through function analysis. However, as a large number of concepts are generated, it is difficult to evaluate and optimize these design candidates using regular algorithm. It is necessary to develop a new approach or a tool to solve the concept generation. Generally speaking, concept generation is a problem of concept synthesis. In substance, this process of developing design candidate is a combinatorial optimization process, viz., the process of concept generation can be regarded as a solution for a state-place composed of multi-concepts. In this paper, genetic algorithm is utilized as a feasible tool to solve the problem of combinatorial optimization in concept generation, in which the encoding method of morphology matrix based on function analysis is applied, and a sequence of optimal concepts are generated through the search and iterative process which is controlled by genetic operators, including selection, crossover, mutation, and reproduction in GA. Several crucial problems on GA are discussed in this paper, such as the calculation of fitness value and the criteria for heredity termination, which have a heavy effect on selection of better concepts. The feasibility and intellectualization of the proposed approach are demonstrated with an engineering case. In this work concept generation is implemented using GA, which can facilitate not only generating several better concepts, but also selecting the best concept. Thus optimal concepts can be conveniently developed and design efficiency can be greatly improved.

• Applied Chemistry for Engineering
• /
• v.18 no.4
• /
• pp.344-349
• /
• 2007

NaY zeolites synthesized by microwave heating were compared with those obtained by conventional heating. When the same temperature increasing rates were adopted in both heating methods, the microwave heating shortened the induction period and enhanced the rate of crystallization of NaY zeolites compared with the conventional heating. Irrespective of microwave radiation, the fast temperature increasing rate also shortened the induction time and enhanced the crystallization of NaY zeolites. The crystal sizes of NaY zeolites were large under the fast temperature raise of the reaction mixture and became larger by microwave radiation. At the same time, the fast temperature increasing rate has reduced the energy consumption due to the fast completion of reaction during the synthesis of NaY zeolite. The energy consumption in the conventional ethylene glycol bath was lower than that in the microwave oven with the same temperature increasing rate in this study, which means that the energy efficiency is not always high in microwave heating. If the temperature increasing rate is carefully controlled, however, NaY zeolite can be produced with high energy efficiency in the microwave oven.

• Archives of Plastic Surgery
• /
• v.42 no.1
• /
• pp.59-67
• /
• 2015

Background Negative-pressure wound therapy (NPWT) induces angiogenesis and collagen synthesis to promote tissue healing. Although acetic acid soaks normalize alkali wound conditions to raise tissue oxygen saturation and deconstruct the biofilms of chronic wounds, frequent dressing changes are required. Methods Combined use of NPWT and acetic acid irrigation was assessed in the treatment of chronic wounds, instilling acetic acid solution (1%) beneath polyurethane membranes twice daily for three weeks under continuous pressure (125 mm Hg). Clinical photographs, pH levels, cultures, and debrided fragments of wounds were obtained pre- and posttreatment. Tissue immunostaining (CD31, Ki-67, and CD45) and reverse transcription-polymerase chain reaction (vascular endothelial growth factor [VEGF], vascular endothelial growth factor receptor [VEGFR]; procollagen; hypoxia-inducible factor 1 alpha [HIF-1-alpha]; matrix metalloproteinase [MMP]-1,-3,-9; and tissue inhibitor of metalloproteinase [TIMP]) were also performed. Results Wound sizes tended to diminish with the combined therapy, accompanied by drops in wound pH (weakly acidic or neutral) and less evidence of infection. CD31 and Ki-67 immunostaining increased (P<0.05) post-treatment, as did the levels of VEGFR, procollagen, and MMP-1 (P<0.05), whereas the VEGF, HIF-1-alpha, and MMP-9/TIMP levels declined (P<0.05). Conclusions By combining acetic acid irrigation with negative-pressure dressings, both the pH and the size of chronic wounds can be reduced and infections be controlled. This approach may enhance angiogenesis and collagen synthesis in wounds, restoring the extracellular matrix.