• Journal of the Korean Geotechnical Society
• /
• v.24 no.9
• /
• pp.23-32
• /
• 2008

This paper presents the global stability of geosynthetic reinforced segmental retaining walls in tiered configuration. Four design cases of walls with different geometries and offset distances were analyzed based on the FHWA and NCMA design guidelines and the discrepancies between the different guidelines were identified. A series of global slope stability analyses were conducted using the limit-equilibrium analysis and the continuum mechanics based shear strength reduction method with the aim of identifying failure patterns and the associated factors of safety. The results indicated among other things that the FHWA design approach yields conservative results both in the external and internal stability calculations, i.e., lower factors of safety, than the NCMA design approach. It was also found that required reinforcement lengths are usually governed by the global slope stability requirement rather than the external stability calculations. Also shown is that the required reinforcement lengths for the upper tiers are much longer than those based on the current design guidelines.

• Advances in aircraft and spacecraft science
• /
• v.10 no.3
• /
• pp.223-243
• /
• 2023

There is a burgeoning demand for minimizing the mass of satellites because of its direct impact on reducing launch-to-orbit cost. This must be done without compromising the structure's efficiency. The present paper introduces a relatively low-cost and easily implementable approach for optimizing structural mass to a maximum natural frequency. The natural frequencies of the satellite are of utmost pertinence to the application requirements, as the sensitive electronic instrumentation and onboard computers should not be affected by the vibrations of the satellite structure. This methodology is applied to a realistic model of Al-Azhar University micro-satellite in partnership with the Egyptian Space Agency. The procedure used in structural design can be summarized in two steps. The first step is to select the most favorable primary structural configuration among several different candidate variants. The nominated variant is selected as the one scoring maximum relative dynamic stiffness. The second step is to use perforation patterns reduce the overall mass of structural elements in the selected variant without changing the weight. The results of the presented procedure demonstrate that the mass reduction percentage was found to be 39% when compared to the unperforated configuration that had the same plate thickness. The findings of this study challenge the commonly accepted notion that isogrid perforations are the most effective means of achieving the goal of reducing mass while maintaining stiffness. Rather, the study highlights the potential benefits of exploring a wider range of perforation unit cells during the design process. The study revealed that rectangular perforation patterns had the lowest efficiency in terms of modal stiffness, while triangular patterns resulted in the highest efficiency. These results suggest that there may be significant gains to be made by considering a broader range of perforation shapes and configurations in the design of lightweight structures.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.409-412
• /
• 2000

In this paper we have implemented CH-MUX system which provides customers with various services, i.e. POTS, ISDN, digital leased line and so on, and supports not only UDLC but IDLC network configuration based on existing optical transmission facilities. Also the RCS equipment has been designed and implemented for remote monitoring and control of CH-MUXs. And then this paper has described IPC procedure and proposed other implemental methods of IPC channel. Service providers will be able to design and construct cost-effective access network with RCS and CH-MUX systems.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10b
• /
• pp.1611-1616
• /
• 1991

A high power stewart platform is designed and manufactured to simulate the 6 degrees of freedom motion of moving vehicle. This paper describes the design of such a motion system including kinematic and kinetic analysis, real time servo control mechanical and hydraulic system configuration, and techniques of regeneration of test records. Discussions are also presented for an algorithm called remote parameter control, which has been developed to compensate the dynamic delay of the electro-hydraulic servo actuators and the nonlinearities of stewart platform.

• Tribology and Lubricants
• /
• v.11 no.2
• /
• pp.63-70
• /
• 1995

The analytical design method of gerotor profile, based on an envelope of a family of curves, is proposed. Analysis to calculate the flow rate and the torque capacity of a gerotor set are presented. The influence of the circular tooth radius and the amount of eccentricity on the configuration of a gerotor has been explored in this paper. The variation of the inlet volume and the fluctuation of the generated torque are also analyzed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.315-319
• /
• 1993

A dynamic modeling, analysis, and optimum design issuess for the Hybrid type of robot are addressed. The dynamic modeling can be used to describe acceleration and velocity properties of the system explicitly in terms of the actuating forces is coded in C language based on the kinematic influence coefficients(KIC). By using this modeling simulation, the actuating forces needed for the robot follows the given trajectory are calculated. Also, for the design concept, the optimum geometric configuration of the system that minimizes the maximum actuating forces is found by using the optimization techique.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.308-313
• /
• 1993

In this paper, the navigation computer design of RPV(remotely piloted vehicle) using GPS is investigated, and its hardware and software structures are described. The proposed hardware adopts the common PC configuration by using 5016A micro PC card and software is divided into several modules such as navigation module, guidance module and control module, etc. The performance of the navigation computer is verified through PILS(process in the loop simulation).

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1728-1735
• /
• 1989

A design procedure for microstrip bandpass filters using step impedance resonators (SIR's) and tapped input/output to a conventional parallel coupled line bandpass filter is presented. The filter configuration consisting of both half-wavelength and SIR's suppreses to spurious resonance response near the second harmonics, while tapping techniques offer benefit in situations where the impractical. The measured frequency responses of the designed filter are in close agreement with the computed responses.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.843-846
• /
• 2008

Rationality of strength models for structural concrete depends on how to treat loads on boundaries and load paths within members. Differentiation between strut-and-tie models and stress fields approaches for shear strength models is discussed in this paper for salient use of current design formula in design code provisions. How to model configuration of loads and stress states along the boundary for the regions under provides a key to realistic construction of stress fields together with STM.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.76-81
• /
• 1989

This paper represents the preliminary design process and the performance of the sounding rockets. At the design phase of the development, we selected rocket configuration according to results of aerodynamic weight and thrust analysis. And the payload-apogee performance of the rockets are determined with the variation of the launch angle and payload weight. Also the performance trajectory was calculated by a particle trajectory simulation. And the parameters which affect the system performance was analyzed.