• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.636-643
• /
• 1995

The accurate determination of the fuel-cladding gap conductance as functions of rod burnup and power level may be a key to the design and safety analysis of a reactor. The incorporation of a sophisticated gap conductance model into nuclear design code for computing thermal hydraulic feedback effect has not been implemented mainly because of computational inefficiency due to complicated behavior of gap conductance. To avoid the time-consuming iteration scheme, simplification of the gap conductance model is done for the current design model. The simplified model considers only the heat conductance contribution to the gap conductance. The simplification is made possible by direct consideration of the gas conductivity depending on the composition of constituent gases in the gap and the fuel-cladding gap size from computer simulation of representative power histories. The simplified gap conductance model is applied to the various fuel power histories and the predicted gap conductances are found to agree well with the results of the design model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2488-2493
• /
• 2007

A gap conductance is very important factor which can affect nuclear fuel temperature. Especially, in case of an annular fuel, a gap conductance effect can lead an unexpected heat split phenomena which is caused by a large difference of an inner and outer gap conductance. The gap conductance mechanism is very complicated behavior due to the its strong dependency on microscopic factors such as a contact surface roughness, local contact pressure and local temperature. In this paper, for the decision of test temperature and pressure range, a procedure and calculation results of in-reactor fuel temperature and pressure analysis are summarized which can be applied to test equipment design and determination of test matrix. Based upon analysis results, it is concluded that the minimum and maximum test temperature are $300^{\circ}C$ and $530^{\circ}C$ respectively, and the maximum pellet/cladding interfacial contact pressure should be observed up to 45MPa.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1569-1573
• /
• 2004

Two ring-type conductance meters were manufactured to measure void fraction and its propagation speed in slug flow. The signal of conductance meter with two rings depends on liquid temperature. Therefore a conductance meter with separated probe designed by Coney (1973), which is independent of liquid temperature, was used and experimentally proved. The manufactured conductance meters showed a good repeatability and agreement with the analytical solution by Coney (1973). From time lag between two conductance meter, we could calculate the propagation speed of void fraction.

• 산업기술연구
• /
• 제28권B호
• /
• pp.117-122
• /
• 2008

This paper presents the conductance model at high frequency of the Ceramic Metal Halide Lamp and the designing method of the electronic ballast with the LCC resonant tank type by using that model. Conductance model is based on a physical phenomenon in the discharge tube of the lamp and model constants of conductance model are obtained by Least Squares Method. After equivalent impedances are determined by the conductance model, The LCC resonance tank is designed by using the equation of the lamp power. Simulation result using PSpice software and experimental results show that the conductance model in this paper is very useful to design the electronic ballast at high frequency for the Ceramic Metal Halide Lamps.

• 한국진공학회지
• /
• 제1권1호
• /
• pp.16-23
• /
• 1992

Conductance calculation is essential in designing a vacuum system. Since mathematical solution is nearly impossible except for a few simple cases, it has been so usual to calculate the conductance for a series connection of components using an approximate formula by Oatley. However, Oatley's formula has a fundamental flaw of totally neglecting the effect of gas beaming. In this study, a new technique is suggested for calculating the conductance with the same accuracy as the Monte Carlo method but with much less computing time, and applied to a system of tube connections in series. The effects of gas beaming in the calculation of conductance is analyzed quantitatively by comparing the conductance calculated by this method with those from Oatley's formula.

• 충청수학회지
• /
• 제18권2호
• /
• pp.205-213
• /
• 2005

We introduce the conductance and examine its properties. We study the local behavior of quasiconformal mappings on the boundary of a domain $D{\subset}\overline{R}^n$ n and present some geometric applications of conductance.

• The Korean Journal of Physiology and Pharmacology
• /
• 제2권1호
• /
• pp.95-100
• /
• 1998

The conductance change evoked by step depolarization was studied in primarily cultured rat adrenal chromaffin cells using patch-clamp and capacitance measurement techniques. When we applied a depolarizing pulse to a chromaffin cell, the inward calcium current was followed by an outward current and depolarization-induced exocytosis was accompanied by an increase in conductance trace. The slow inward tail current which has the same time course as the conductance change was observed in current recording. The activation of slow tail current was calcium-dependent. Reversal potentials agreed with Nernst equation assuming relative permeability of $Cs^+\;to\;K^+$ is 0.095. The outward current and tail current were blocked by apamin (200 nM) and d-tubocurarine (2 mM). The conductance change was blocked by apamin and did not affect membrane capacitance recording. We confirmed that conductance change after depolarization comes from the activation of the SK channel and can be blocked by application of the SK channel blockers. Consequently, it is necessary to consider blocking of the SK channel during membrane capacitance recording.

• Journal of Advanced Marine Engineering and Technology
• /
• 제8권1호
• /
• pp.4-16
• /
• 1984

The heat-pipe is characterised by the highly effective thermal conductance. In order to change the thermal conductance, the heat-pipe is connected to a reservior having a space which is filled with non-condensable gas. In normal operation, the vapour of working fluid will tend to pump the non- condensable gas into the reservoir and the gas-vapour interface situates at some point along the condenser section. The thermal conductance is affected by non- condensable gas. It is concluded that the suitable position of interface can be used to control the temperature of condenser section. In this experiment, the evaporating part is connected to the lowest position of heat-pipe. The copper heat-pipe which is filled with Freon-113 or distilled water as working fluid utilized. As results of experimental study, thermal conductance can be increased by the operating pressure which is infulenced by non-condensable gas. A correlative equation between the thermal conductance and the mass of non- condensable gas is also obtained.

• 전기전자학회논문지
• /
• 제4권2호
• /
• pp.192-201
• /
• 2000

이 논문은 연속형 Hopfield 신경회로망에서 뉴론의 입력단에 연결하는 컨덕턴스가 시스템의 안정도에 미치는 영향에 대해 논의 하고자 한다. 이 컨덕턴스는 뉴론의 입력단과 ground사이에 캐패시터와 병렬로 연결되어 있는 데, 시스템의 안정도에 영향을 미치는 것으로 알려져 있으나, 이 것에 대해 알려진 것이 별로 없어, 여기서 그 것에 자세히 논의 한다. 그리고 또한 이 컨덕턴스를 조절하여 시스템의 안정도와 더불어 시스템의 performance를 개선하는 방법에 대해 다룬다.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권5호
• /
• pp.626-632
• /
• 1995

In this paper, The effect of the impedances in SNOSFET's memory devices has been developed. The effect of source and drain impedances measured by means of two bias resistances - field effect bias resistance by inner region, external bias resistance. The effect of the impedances by source and drain resistance shows the dependence of the function of voltages applied to the gate. It shows the differences of change in source drain voltage by means of low conductance state and high conductance state. It shows the delay of threshold voltages. The delay time of low conductance state and high conductance state by the impedances effect shows 3[.mu.sec] and 1[.mu.sec] respectively.