• 한국건설순환자원학회논문집
• /
• 제6권1호
• /
• pp.50-58
• /
• 2018

콘크리트 구조물의 사용성능을 검증하기 위하여 콘크리트와 철근의 상호 합성 작용에 대한 많은 정보가 필요한데, 균열폭 및 균열간격의 평가는 두 재료의 상호작용인 인장강화효과에 근거하여 이루어진다. 이 논문에서는 압축강도 80MPa 및 100MPa의 고강도 콘크리트에 D13 철근을 사용한 인장부재를 제작하여 직접인장실험을 진행하였다. 이를 통해 고강도 콘크리트의 인장강화 효과를 파악하였고 보통강도 콘크리트의 실험결과에 근거한 현행설계기준의 인장강화효과 평가가 부적절함을 확인하였다. 실험결과에 근거하여 고강도 콘크리트 콘크리트의 특성을 적절하게 반영할 수 있는 실험계수를 산정하였다. 또한 균열거동을 통해서 균열간격을 파악하고 이를 통해 고강도 콘크리트의 인장강화효과에 따른 철근변형률과 콘크리트 변형률 차이에 따른 균열폭을 확인하였다. 이 연구의 결과는 향후 고강도 콘크리트 부재의 인장강화 효과를 연구하는 기초자료로 활용될 수 있을 것이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.635-640
• /
• 2000

This paper describes an experimental investigation on the influence of concrete strength on tension stiffening behavior. Total 6 direct tension specimens were tested with variation of concrete strengths such as 260, 620, and 820kgf/$\textrm{cm}^2$. These test results were compared with tension stiffening models of CEB-FIP Model Code. It was appeared that, as concrete strength was increasing, CEB-FIP models estimated much more tension stiffening than these test results. As the result, it would be said that the influence of concrete strength on tension stiffening was not properly taken account for in CEB-FIP model.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1784-1800
• /
• 2018

Tension-shear loading is a common loading condition in steel structures during the earthquake shaking. To study ductile fracture in structural steel under multiple stress states, experimental investigations on the different fracture mechanisms in Chinese Q235 steel were conducted. Different tension-shear loading conditions achieved by using six groups of inclined notch butterfly configurations covering pure shear, tension-shear and pure tension cases. Numerical simulations were carried out for all the specimens to determine the stress and strain fields within the critical sections. Two tension-shear fracture models were calibrated based on the hybrid experimental-numerical procedure. The equivalent fracture strain obtained from the round bar under tensile loading was used for evaluating these two models. The results indicated that the tension-shear criterion as a function of the shear fracture parameter had better performance in predicting the fracture initiation of structural steel under different loading conditions.

• 한국농공학회지
• /
• 제41권4호
• /
• pp.104-112
• /
• 1999

Tensile behavior in concrete has been neglected until recently. However, the effect of tensile stresses in concrete must be considered where the member primarily carries tensile forces or when ultimate strength is affected by the cracking history. In this paper, a series of experiments were performed with a reinforced rectangular beams of 15 specimens in order to investigate the effect of tension stiffening into the nonlinear analysis and cracking behavior. The experimental results were analyzed in terms of load-deflection curves and strain fracture energy with respect to the main experimental variables such as types of specimen, strength of concrete and steel ration. The results from experiments and finite element analysis were compared in terms of load-deflection relationship and cracking pattern. The results are as follows ; The tension stffening effects of reinforced concrete beams were observedc up to yielding of members after cracking showing strain energy difference of 35 % at the beam of 0.57% steel ratio compared with that of beam ignoring the tension stiffening effect. The tension stiffening of concrete strength 400kgf/$\textrm{cm}^2$ and 600kgf/$\textrm{cm}^2$ increased by 8% and 13%, respectively, compared with that of concrete strength 200kgf/$\textrm{cm}^2$. The tension stiffening effects were greater at a ductile member rather than a brittle one. The load-deflection results of finite element analysis showed very similar results from experiment. The crack growth and pattern might be predicted from the nonlinear finite element analysis considering concrete stiffening.

• Structural Engineering and Mechanics
• /
• 제40권6호
• /
• pp.847-866
• /
• 2011

The objective of this study was to experimentally investigate the bond-related tension stiffening behavior of flexural reinforced concrete (RC) beams made with lightweight aggregate concrete (LWAC) under various high-cycle fatigue loading conditions. Based on strain measurements of tensile steel in the RC beams, fatigue-induced degradation of tension stiffening effects was evaluated and was, compared to reinforced normal weight concrete (NWC) beams with equal concrete compressive strengths (40 MPa). According to applied load-mean steel strain relationships, the mean steel strain that developed under loading cycles was divided into elastic and plastic strain components. The experimental results showed that, in the high-cycle fatigue regime, the tension stiffening behavior of LWAC beams was different from that of NWC beams; LWAC beams had a lesser reduction in tension stiffening due to a better bond between steel and concrete. This was reflected in the stability of the elastic mean steel strains and in the higher degree of local plasticity that developed at the primary flexural cracks.

• KIEAE Journal
• /
• 제8권5호
• /
• pp.61-68
• /
• 2008

For the recycling of the resources and the preservation of the environment, this study's purpose is to measure flexural behavior of the reinforced concrete beams with the major variables like concrete strength, replacement ratio of the recycled aggregate and the waste foundry sand and the tension reinforcement ratio and to present the data of the recycled aggregate used for the structure design. The experiment on the flexural behavior resulted in the followings. The ultimate strength of recycled R/C beam was manipulated proportionate to the tension reinforcement ratio, however the strength instantly decreased after passing the ultimate load due to the destroyed concrete of the compression side. The deflection at the maximum load varied from the tension reinforcement ratio by 5.5 times. The test specimen with the tension reinforcement ratio less than $0.5{\rho}b$ showed constant curve without change in the load from the yield to the ultimate load in contrast to the distinctive plastic region where the displacement was rising. Although the strain of main tension steel with the reinforcement ratio indicate different, the design of recycled concrete member can be applied for current design code for reinforced concrete structure as the ratio of tension reinforcement district the under the reinforcement ration in a balanced strain condition.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.141-148
• /
• 1998

An analytical model which can simulate the post-cracking behavior of reinforced concrete structures subjected to in-plane shear and normal stresses is presented. Based on the force equilibriums, compatibility conditions, and bond stress-slip relationship between steel and concrete, a criterion to simulate consider the tension-stiffening effect is proposed. The material behavior of concrete is described by an orthotropic constitutive model, and focused on the tension-compression region with tension-stiffening and compression softening effects defining equivalent uniaxial relations in the axes of orthotropy. Correlation studies between analytical results and available experimental data are conducted with the objective to establish the validity of the proposed model.

• 산업기술연구
• /
• 제17권
• /
• pp.145-151
• /
• 1997

This paper presents evaluation results of the tensile behavior of reinforced high strength concrete. The effects of different sizes of reinforcing bar, ranging from D22 to D29, on the formation of cracks was investigated. Two different strength concretes, $270kg/cm^2$ and $550kg/cm^2$, were used in the specimens to investigate the influence if concrete strength on tension stiffening. In the present investigation a method was developed to obtain reliable load-deformation behavior in tension. The experimental results show that (1)high-strength concrete members exhibited larger amounts of tension stiffening than the companion normal-strength concrete members, (2) as the bar diameter increases, the beneficial influence of high-strength concrete on tension stiffening is reduced.

• Advances in concrete construction
• /
• 제5권1호
• /
• pp.75-86
• /
• 2017

An experimental work was carried out to study the effect of hybrid fiber on the tension stiffening and cracking characteristics of geopolymer concrete (GPC). A total of 24 concentrically reinforced concrete specimens were cast and tested under uniaxial tension. The grade of concrete considered was M40. The variables mainly consist of the volume fraction of crimped steel fibers (0.5 and 1.0%) and basalt fibers (0.1, 0.2 and 0.3%). The load deformation response was recorded using LVDT's. At all the stages of loading after the first cracking, crack width and crack spacing were measured. The addition of fibers in hybrid form significantly improved the tension stiffening effect. In this study, the combination of 0.5% steel fiber and 0.2% basalt fiber gave a better comparison than the other combinations.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.197-200
• /
• 2005

This paper presents an analytical model for evaluation of Tension Stiffening Effect by actual Bond-Slip relationships between the reinforcement and the surrounding concrete. The presence of longitudinal splitting cracks was found to significantly after the tension stiffening. The model is applied to the longitudinal splittings cracks and derived to Tension stiffening model. The predicted values are shown to be in good agreement with the experimentally measured data.