• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1416-1428
• /
• 2021

Pebble flow characteristics can be significantly affected by the configuration of pebble bed, especially for HTGR pebble beds. How to achieve a desired uniform flow pattern without stagnation is the top priority for reactor design. Pebbles flows inside some specially designed pebble bed with arc-shaped contraction configurations at the bottom, including both concave-inward and convex-outward shapes are explored based on discrete element method. Flow characteristics including pebble retention, residence-time frequency density, flow uniformity as well as axial velocity are investigated. The results show that the traditionally designed pebble bed with cone-shape bottom is not the most preferred structure with respect to flow pattern for reactor design. By improving the contraction configuration, the flow performance can be significantly enhanced. The flow in the convex-shape configuration featured by uniformity, consistency and less stagnation, is much more desirable for pebble bed design. In contrast, when the shape is from convex-forward to concave-inward, the flow shows more nonuniformity and stagnation in the corner although the average cross-section axial velocity is the largest due to the dominant middle pebbles.

• KSTLE International Journal
• /
• 제10권1_2호
• /
• pp.27-32
• /
• 2009

In this study, fretting wear tests of nuclear fuel rods have been performed by using two kinds of spacer grid springs with a concave and a convex shape in room temperature dry and distilled water conditions. The objectives were to examine the variation of the wear mechanism with increasing fretting cycles and to evaluate the difference of the wear debris detachment behavior at each test environment. From the test results, the wear volume of each spring condition increased with increasing fretting cycles regardless of the test environments. However, the wear rate did not show a regular tendency and apparently changed with increasing fretting cycles. This is because the formation of the wear particle layer and/or the variation of the contact condition between the fuel rod and spring surfaces could affect a critical plastic deformation for detaching the wear debris. Based on the test results, the relationship between the wear behavior of each spring shape and test environment condition, and the variation of the surface characteristics are discussed in detail.

• Journal of Welding and Joining
• /
• 제17권4호
• /
• pp.76-84
• /
• 1999

The residual stress generated when the steel plates were produced, did not influence on the out-of-plane deformation and residual stress generated by welding. When the initial deflection shape was a concave(Type I), the out-of-plane deformation became the same shape as that of the initial deflection and its magnitude became small. When the initial deflection made a winding in the welding direction(Type III), the out-of-plane deformation became large in the plate width. The initial deflection shape did not influence on residual stress and plastic strain produced by welding.

• 한국정보과학회논문지:컴퓨팅의 실제 및 레터
• /
• 제8권1호
• /
• pp.116-125
• /
• 2002

본 논문에서는 클립아트 이미지에서 모양 정보를 추출하고 이 정보를 이용하여 클립아트 이미지의 유사도를 측정하는 방법을 제안하였다. 본 논문에서 사용하는 클립아트 이미지는 자연영상에 비해 외곽선을 명확하게 추출할 수 있다는 장점이 있다. 이미지에서 모양 정보를 추출하는 이전의 방법은 모양의 외곽선을 이용하는 것과 영역을 이용하는 것으로 분류할 수 있는데 본 논문에서는 모양의 외곽선을 이용하는 것으로 외곽선의 오목한 부분과 볼록한 부분을 직사각형의 비율로 표현하는 방식을 제안하였다. 이렇게 함으로서 기존의 외곽선 기반 특징을 이용하는 방식보다 모양 정보를 더욱 잘 표현할 수 있었다.

• Journal of the Korean Data and Information Science Society
• /
• 제16권4호
• /
• pp.1141-1145
• /
• 2005

In this note, we show that Theorem 2.1[Kybernetika, 28(1992) 45-49], a result of a functional relationship between the membership function of LR fuzzy numbers of T-sum and T-product, remains valid for convex additive generator and concave shape functions L and R with simple proof. We also consider the case for 0-symmetric R fuzzy numbers.

• 치과방사선
• /
• 제18권1호
• /
• pp.203-212
• /
• 1988

This study was designed to observe mandibular condyle shape and position in an asymptomatic popular ion. Using Accurad-200 head holder(Denar Corp.) for transcranial radiography of the temporo-mandibular joint region, transcranial radiographs were taken at the centric occlusion and 1 inch mouth opening in 73 males and females who were asymptomatic for TMJ disturbances, had no severe carious or missing teeth, and no history of prosthodontic or orthodontic treatments. Mandibular condyles were classified morphologically at the centric occlusion and evaluated in positional relationship with mandibular fossa and articular eminence at the centric occlusion and 1 inch mouth opening. The results were as follows: 1. In the morphologic classification of mandibular condyle, the convex shape was more prevalent in an asymptomatic population(90.4%), the locally concave shape and wedge shape were 5.5%, 4.1%. 2. At the centric occlusion, the means of joint space were 3.43nm superiorly, 2.17㎜ anteriorly, and 2.61㎜ posteriorly. 3. At the centric occlusion, the mandibular condyles were placed slightly anterior to the center of their fossa. 4. At the 1 inch mouth opening, the mandibular condyles were placed anterior to the articular eminence more than posterior to or below the top of the articular eminence.

• 설비공학논문집
• /
• 제10권3호
• /
• pp.324-333
• /
• 1998

Measurements of the local heat transfer coefficients on a hemispherically concave surface with a round oblique impinging jet were made. The liquid crystal transient method was used for these measurements. This method, which is a variation of the transient method, suddenly exposes a preheated wall to an impinging jet while video recording the response of liquid crystal for the surface temperature measurements. The Reynolds number used was 23,000 and the nozzle -to -jet distance was L/d=2, 4, 6, 8 and 10 and the jet angle was $\alpha$=0$^{\circ}$, 15$^{\circ}$, 30$^{\circ}$and 40$^{\circ}$. In the experiment, the maximum Nusselt number at all region occurred at L/d(equation omitted)6 and Nusselt number decreases as the inclined jet angle increases. For the normal jet the contours of constant Nusselt number are circular and as the jet is inclined closer and closer to the surface the contours become elliptical shape. The decreasing rate of the Nusselt number at X/d＞ 0(upstream) on a surface curvature are higher than those on a flate plate and the decreasing rate of the Nusselt number at X/d ＜0(downstream) on a surface curvature are lower than those on a flate plate. And also, the decreasing rate of local Nusselt number distribution at X/d ＜0(upstream) exhibit lower than with X/d ＜0(downstream) as jet angle increases. The second maximum Nusselt number occurred at long distance from stagnation point as jet angle increases.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.59-65
• /
• 2004

In this paper a numerical study was performed for the effect of the wall curvature on the behaviors of fuel sprays impinging on the concave Surface. Actually, in the real diesel engines, a piston head has a curved shape for the purpose of the controlling the movement of fuel droplets and the mixture formation. For past decades, although many experimental and numerical works had been performed on the spray/wall impingement phenomena, the curvature effect of impinged wall was rarely investigated. The wall curvature affects on the behaviors of the secondary droplets generated by impingement and the concave wall obstructs the droplets to advance from the impinging site to outward. In present study, the simulation code was validated for the flat surface case and three cases of the different curvature were calculated and compared with the flat surface case for several parameters, such as the spray radius, the spray height and the position of vortex center of gas phase. The simulation results showed that the radial advance of the wall spray and the vortex is decreased with increasing the curvature. It was concluded that the curvature of the impinged wall significantly affects the behaviors of both the gas-phase and the droplet-phase.

• 대한산업공학회지
• /
• 제27권1호
• /
• pp.69-88
• /
• 2001

In the zigzag milling operation, an important issue is to design a machining strategy which minimizes the cutting time. An important variable for minimization of cutting time is the tool path length. The tool path is divided into cutting path and non-cutting path. Cutting path can be subdivided into tool path segment and step-over, and non-cutting path can be regarded as the tool retraction. We propose a new method to determine the cutting direction which minimizes the length of tool path in a convex or concave polygonal shape including islands. For the minimization of tool path length, we consider two factors such as step-over and tool retraction. Step-over is defined as the tool path length which is parallel to the boundary edges for machining area and the tool retraction is a non-cutting path for machining any remaining regions. In the determination of cutting direction, we propose a mathematical model and an algorithm which minimizes tool retraction length in complex shapes. With the proposed methods, we can generate a tool path for the minimization of cutting time in a convex or concave polygonal shapes including islands.

• 설비공학논문집
• /
• 제9권4호
• /
• pp.435-445
• /
• 1997

It was studied the phenomena of transient freezing of an inclined water-saturated enclosure. One side of the test section was cooled and the other sides were insulated. The effects of the initial temperature, the inclination angle on the temperature field and the shape of the ice-water interface were observed. In the beginning of freezing, with increasing the inclination angle the freezing rate was increased and in the stable density layer centered $4^{\circ}C$, the freezing was fast as the convective fluid flow became small. When the initial temperature was above the $4^{\circ}C$, the frozen thickness in the upper part of inclined surface was thinner than that in the lower part, but with time the frozen thickness of upper part was thicker than that of lower part, below the $4^{\circ}C$, the frozen thickness in the upper part was thicker than that of lower part from the begining, and above the $8^{\circ}C$ in the beginning upper part was thinner with concave, but with time thicker the upper part, vanishing concave.