• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.11
• /
• pp.2771-2778
• /
• 2014

In this paper, we propose an algorithm that select efficient relay nodes using information of network environment and nodes. The proposed algorithm can be used changeable weight factors as following network environment in node density. The routing protocols adopting store-carry-forward method are used for solving network problems occurred by unstable end-to-end connection in Delay Tolerant Networks(DTNs). Exiting DTN routing algorithms have problems that large latency and overhead because of deficiency of network informations. The proposed algorithm could be provide a solution this problems using changeable weight factor and prediction of network environment. Thus, selected relay nodes work efficiently in unstable and stressed network environment. Simulation results show that enhancement performance as overhead, delivery ratio, average latency compared to exiting DTN routing algorithm.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.E1
• /
• pp.21-28
• /
• 2003

An auxiliary device, called Post Cyclone (PoC). had been introduced and primarily examined in earlier works which proved the reduction of the emission of fine dust from the gas-solid cyclones without incurring significant increase of cost and pressure drop. It has been known that the PoC has some advantages over other secondary dust treatment devices such as (a) simple design, (b) low cost of manufacture, (c) minimum additional pressure drop, (d) high recoverbility of the product dust, and (e) simplicity of operation. Despite the potential advantage, however, lack of practical data confined its plausible application in wide areas. Thus, in this work, a few serial experiments were conducted in terms of a few operation conditions, and the particle trajectories throughout the cyclone set-up were visually analyzed by using a commercial computer simulation program (FLUENT).

• Proceedings of the KIEE Conference
• /
• 1979.08a
• /
• pp.119-120
• /
• 1979

A linear state equation of the first order differential form relating the load-frequency dynamic characteristics of interconnected power systems was derived for use in computer simulation. A now solution of the algebraic matrix riccati equation for application in quadratic optimal controllor and least-square state estimator dermination was developed. The program for a dynamic state equation for two interconnected control areas was developed. The optimized load-frequency deviation was analysed and a numerical analysis was tried based on the computer simulation. It was shown that the dynamic response of th loed-frequency could be optimized with weighting factors IR and Q. The result was that the load-frequency and the tie-line deviation were visibly reduced.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.152-157
• /
• 2001

UTC(Unglazed Transpired Collector) system has recently emerged as a new solar air heating technology. It is relatively inexpensive because it has not a glazed material. And it demonstrates efficient particularly for the applications in which larger wall area facilities with a high outdoor air requirement. Mathematical algorithm for UTC thermal modeling has been understood for further improvement of the system. EES and TRNSYS model of actual solar wall panel could be developed for computer simulations under other conditions. Computer models could be validated with the measured data from fixed outdoor test cell in KIER(Korea Institute of Energy Research). Major design parameters could be identified such as panel configuration and absorptivity and emissivity values for UTC design.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.749-753
• /
• 2007

The purpose of this study is to design of a linear feeder using a multi body dynamic program, and to analyze a dynamic motion of the feeder that can transport small mechanical parts uniformly. In order to establish the analysis model of the linear feeder, each parts of the feeder are divided into two types which the rigid and flexible body. For the dynamic simulation, RecurDyn, which is a commercial multi-body dynamic package, is used. We also consider the design parameters for optimal dynamic motion such as centroid, stiffness, and mass of the feeder system. In order to analyze the dynamic motion of a linear feeder, the displacements of the feeder are measured by several accelerometers when it is in an operating condition. After the signal data from the accelerometers are captured in the time domain, the dynamic motion in the space is visualized by using graphic computer software.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.2926-2935
• /
• 1993

Chip breaker selection analysis, only being possible through experimental process, was obtained by a applied equation which used an orthogonal cutting model and a basic chip deformation. This equation could present an analysis of the chip breaking phenomena without the use of an actual experimetal method, and it was applied to computer simulation and proved the validity of theory through actual experiments. From these results, an efficient method for finding the optimum conditions of chip breaking was found through an optimized theory being applied to basic program. A finite element model for simulating chip breaking in orthogonal cutting was developed and discussed. By simulation the animation of chip breaking is observed in process on the computer screen.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.9
• /
• pp.1199-1206
• /
• 2002

This study is to verify the application characteristics of PI control and to simulate the applicability of Neural Networks control HVAC TRNSYS program. Each performance of HVAC by PI control and by Neural Networks is compared. According to the result of simulation, Neural Networks control is favorably applicable than previous PI control for the variation of weather condition and systematic changes.

• Journal of the Ergonomics Society of Korea
• /
• v.14 no.1
• /
• pp.105-113
• /
• 1995

The objective of the study is to investigate the influence of aesthetic attributes on user interface design. Theories of aesthetics are first studied from which aesthetic attributes are defined as information sources. Representation of a product is viewed as a combination of aesthetic attributes, based on a hypothesis that each attribute has a certain influence on the performance in terms of user interface. An experiment was conducted to support the hypothesis. Various combinations of aesthetic attributes of a microwave oven were generated from the orthogonal array of a conjoint analysis. Subjects perfomed on a computer two types of tasks, each of which simulated a combination of attributes. Reaction time was evaluated as a performance measure for the conjoint analysis to find out how much influence each attribute has on the performance. A computer program, UISA(User interface Simulation system of Aesthetic attributes0, was developed and used for simulation. Findings on the influences of aesthetic attributes were summarized.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.14-17
• /
• 1992

To analyze Nonvolatile SNOSFET(polySilicon-Nitride-Oxide-Semiconductor Field Effect Transistor) memory device, two dimensional numerical computer simulation program was developed. The equation discretization was performed by the Finite difference method and the solution was derived by the Iteration method. The doping profile of n-channel device which was fabricated by 1Mbit CMOS process was observed. The electrical potential and the carrier concentration distribution to applied bias condition were observed in the inner of a device. As a result of the write and the erase to memory charge quantity, the threshold voltage shift is expected. Therefore, without device fabrication, the operating characteristics of the device was observed under various the processing and the operating condition.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1150-1157
• /
• 1994

This paper presents dynamic analysis of a hydraulic excavator based on experimental data. A three dimensional multibody model of a hydraulic excavator is modeled for the computer simulation. The hydraulic pressures acting on the cylinders are measured from experiments, and the forces exerting on the cylinders are calculated from the measured pressures. Using these forces, the dynamic analysis of the excavator is carried out to regenerate the motion in the computer simulation. A proper operation scheme is assumed to match the computational result and the experiment. The DADS program is used for the dynamic analysis.