• 한국자동차공학회논문집
• /
• 제18권2호
• /
• pp.74-82
• /
• 2010

Fretting damage can be observed in automobile and railway vehicle, fossil and nuclear power plant, aircraft etc. In the present study, railway axle material RSA1 used for evaluation of fretting fatigue life. Plain and fretting fatigue tests were carried out using rotary bending fatigue tester with proving ring and bridge type contact pad. Through these test, the following results are obtained: 1) it is found that the fretting fatigue limit of standard specimen decreased about 37% compared to the plain fatigue limit. 2) The early crack of Shinkansen type specimens initiated in contact area and final fractured below samp=214 MPa. 3) The early crack of all TGV type specimens initiated in rounded area and fractured. 4) Tire tracks and rubbed scars were observed in the oblique crack region and fatigue crack growth region of fracture surface. 5) The wear debris is observed on the contact surface, and oblique cracks at an earlier stage are initiated in contact area. These results can be used as useful data in a structural integrity evaluation of railway axle.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.373-378
• /
• 2013

엔진의 출력증대와 이에 따른 변속기의 크기 증가 등으로 인한 회전체의 관성증가로 변속기의 변속성능은 악조건이 되고 있다. 따라서, 이를 해결하기 위하여 내마모성이 높은 마찰소재의 개발이 요구된다. 디젤차량 수동변속기용 싱크로나이저 링에 요구되는 마찰특성에 적합한 소재를 개발하고, 이에 대한 접합 특성을 평가하였다. 즉, 철합금 모재와 동합금계 마찰재를 접합하는 공정을 개발하고, 접합층에 대하여 BSE분석, EDX분석을 수행하여 접합특성을 평가하였으며, 해당 시험편에 대하여 전단강도를 평가하였다.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.170-177
• /
• 1998

The purpose of superconducting magnetic bearing flywheel energy storage system(SMB-FESS) is to store unused nighttime electricity as kinetic energy and convert it to electricity during daytime. The SMB-FESS is proposed as an efficient energy storage system because there is no mechanical problems, such as friction and wear The flywheel over SMB is rotated at a high speed, 50,000rpm. The major source of energy loss in the SMB-FESS is vibration of flywheel. Therefore, the vibration characteristics of SMB-FESS should be identified. In this study, the axial/radial stiffness and damping coefficient of SMB are measured by a vibration test. Natural frequencies and natural modes of flywheel and magnet are analyzed by a finite element method. The modal analysis of system is performed using the modal parameters of each component and the measured stiffness/damping coefficient. So, natural at frequencies and mode shapes of the joined system can be obtained. According to critical speed analysis, the system has two rigid conical modes in the low speed range. Nevertheless, the system has not been affected by the critical speed in the main operating range.

• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.338-345
• /
• 2002

The study presents a new testing and analysis method for brake judder on vehicle. For the identification of the excitation mechanism of a brake judder, it is necessary to measure the dynamic brake disc geometry during braking on vehicle. The non-contact sensor system was used to monitor the brake disc geometry. Brake torque variation (BTV) caused by disc thickness variation (DTV) is the primary excitation for brake judder. The mechanical effects generating BTV are linked not only to initial manufacturing tolerances but also to uneven wear. Therefore, the brake disc geometry should be strictly managed to initial condition. The aim of this study has been to measure the dynamic DTV and runout on vehicle and analyze the influence of test parameters on brake judder and compare the disc component with vehicle matching about the DTV Profile. As a result of this study, The amplitude of brake judder is proportional to vehicle speed and fluid pressure fluctuation on braking. The major sources of brake judder are directly related to disc thickness variation and side runout variation of corner assembly (disc, hub. bearing).

• International Journal of Reliability and Applications
• /
• 제3권1호
• /
• pp.1-16
• /
• 2002

In reliability engineering, the bathtub-shaped hazard rates play an important role in survival analysis and many other applications as well. For the bathtub-shaped, initially the hazard rate decreases from a relatively high value due to manufacturing defects or infant mortality to a relatively stable middle useful life value and then slowly increases with the onset of old age or wear out. In this paper, we present a new two-parameter lifetime distribution function, called the Loglog distribution, with Vtub-shaped hazard rate function. We illustrate the usefulness of the new Vtub-shaped hazard rate function by evaluating the reliability of several helicopter parts based on the data obtained in the maintenance malfunction information reporting system database collected from October 1995 to September 1999. We develop the S-Plus add-in software tool, called Reliability and Safety Assessment (RSA), to calculate reliability measures include mean time to failure, mean residual function, and confidence Intervals of the two helicopter critical parts. We use the mean squared error to compare relative goodness of fit test of the distribution models include normal, lognormal, and Weibull within the two data sets. This research indicates that the result of the new Vtub-shaped hazard rate function is worth the extra function-complexity for a better relative fit. More application in broader validation of this conclusion is needed using other data sets for reliability modeling in a general industrial setting.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.366-372
• /
• 2017

Plasma electrolytic oxidation(PEO) has attracted attention as a surface treatment which has high wear resistance and corrosion resistance. PEO is generally considered as cost-effective, environmentally friendly and superior in terms of coating performance. Most of studies about the PEO processes have been applied to light metals such as Al and Mg. Because the strength of Al and Mg is weaker than that of steel, there is a limit to the application. In this study, PEO process was used to form oxide coatings on Hot dipped aluminized(HDA) steel and the characteristics of the coating film according to the PEO current density were studied. The morphology was observed by SEM and component was analyzed by using EDS. The corrosion behaviors of PEO coating films were estimated by exposing salt spray test at 5 wt.% NaCl solution and measuring polarization curves in deaerated 3 wt.% NaCl solution. With the increase of PEO process current density, the pore size of the coating surface and the thickness of coating increased. It was confirmed that no Fe component was present on the coating surface. PEO coating films obviously showed good corrosion resistance compared with HDA. It is considered that the PEO coating acts as a barrier to protect the base material from external factors causing corrosion.

• 드라이브 ㆍ 컨트롤
• /
• 제12권1호
• /
• pp.1-8
• /
• 2015

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.

• 한국산학기술학회논문지
• /
• 제9권3호
• /
• pp.593-598
• /
• 2008

브레이크 마찰재의 구성성분 중 기존에 사용되던 무기 충진재인 $BaSO_4$ 대신에 고로슬러지와 그 산화철에 일련의 환원과정을 행하여 얻은 환원분철을 10%, 20%, 30%씩 첨가하면서 몇 종류의 마찰재를 제작하였다. 이 마찰재들에 대해 기본 물성시험, 브레이크 다이마모미터를 사용한 마찰성능 시험 등을 행하였다. 그리고 고가의 충진재인 $BaSO_4$를 환원분철로 대체하여 마찰재에 첨가한 경우, 발열온도, 마모 등의 마찰특성이 우수한 환원분철의 첨가량은 10%이었다. 고로슬러지나 환원분철 시편에서 고로슬러지와 환원분철의 첨가량이 증가할수록 마찰재의 전단강도와 접착강도는 감소하나 모두 마찰재로서의 적용에는 충분한 강도를 나타내었다.

• Corrosion Science and Technology
• /
• 제20권1호
• /
• pp.26-36
• /
• 2021

Pipes operating in the seawater environment faces cavitation degradation and corrosion of the metallic component, as well as a negative synergistic effect. Cavitation degradation shows the mechanism by which materials deteriorate by causing rapid change of pressure or high-frequency vibration in the solution, and introducing the formation and explosion of bubbles. In order to rate the cavitation resistance of materials, constant conditions have been used. However, while a dynamic cavitation condition can be generated in a real system, there has been little reported on the effect of ultrasonic amplitude on the cavitation resistance and mechanism of composites. In this work, 3 kinds of epoxy coatings were used, and the cavitation resistance of the epoxy coatings was evaluated in 3.5% NaCl at 15 ℃ using an indirect ultrasonic cavitation method. Eleven kinds of mechanical properties were obtained, namely compressive strength, flexural strength and modulus, tensile strength and elongation, Shore D hardness, water absorptivity, impact test, wear test for coating only and pull-off strength for epoxy coating/carbon steel or epoxy coating/rubber/carbon steel. The cavitation erosion mechanism of epoxy coatings was discussed on the basis of the mechanical properties and the effect of ultrasonic amplitude on the degradation of coatings.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.49-55
• /
• 2023

Currently, the demand for green technologies toward a sustainable future is rapidly increasing due to growing concern over environmental issues. Methanol is biodegradable and can provide clean combustion to reduce sulfur oxide and nitrogen oxide emissions, and therefore it is a candidate fuel for marine engines. However, the effect of methanol on tribological characteristic degradation should be addressed for methanol-fueled engines. In this study, the methanol addition effects on tribological characteristic degradation is experimentally assessed using a pin-on-disk tribo-tester. Ni-based alloy is used as a target material due to its broad applicability as an engine component material. For a lubricant, engine oil with and without methanol are used. The tests are conducted for up to 10,000 cycles under boundary lubrication while the change in friction force is monitored. Additionally, the wear rate is determined based on laser scanning confocal microscope data. An additional test in which methanol is added at regular intervals is performed with an aim to directly observe its effect on friction. Overall, the friction coefficient increases slightly with increasing methanol concentration. Furthermore, the wear rate of the pin and disk increase significantly with methanol addition. The results also indicate that the friction increases instantaneously with methanol addition at the contacting interface. These findings may be useful for better understanding the methanol effect on the tribological characteristics of Ni-based alloys for methanol-fueled engines with improved performance.