DOI QR코드

DOI QR Code

A Study on Thermal Analytical Model for a Dry Dual Clutch

건식 듀얼 클러치의 열해석 모델에 대한 연구

  • Liu, Hao (Department of Mechanical and Automotive, Engineering, Keimyung University) ;
  • Lee, J.C. (Department of Mechanical and Automotive, Engineering, Keimyung University) ;
  • Noh, Y.J. (Department of Mechanical and Automotive, Engineering, Keimyung University) ;
  • Cho, J.H. (Technical Research Center, Valeo Pyeong Hwa Co.) ;
  • Lee, H.R. (Technical Research Center, Valeo Pyeong Hwa Co.) ;
  • Koh, J.E. (Technical Research Center, Valeo Pyeong Hwa Co.) ;
  • Kang, J.W. (Technical Research Center, Valeo Pyeong Hwa Co.)
  • Received : 2014.11.27
  • Accepted : 2015.02.09
  • Published : 2015.03.01

Abstract

The stability of friction characteristics and thermal management for a dry type dual clutch transmission (DCT) are inferior to those of a wet clutch. Too high temperature resulting from frequent engagement of DCT speeds up degradation or serious wear of the pressure plate or burning of the clutch disk lining. Even though it is significantly important to estimate the temperature of a dry double clutch (DDC) in real-time, few meaningful study of the thermal model of DDC has been known yet. This study presented a thermal analytical model of lumped parameters for a DDC by analyzing its each component firstly. Then a series of experimental test was carried out on the test bench with a patented temperature telemetry system to validate the proposed thermal model. The thermal model, whose optimal parameter values were found by optimization algorithm, was also simulated on the experimental test conditions. The simulation results of DDC temperature show consistency with the experiment, which validates the proposed thermal model of DDC.

Keywords

References

  1. H. Naunheimer, B. Bertsche, J. Ryborz, and W. N. Novak, Automotive Transmissions: Fundamentals, Selection, Design and Application, Springer, New York, pp.163-182 2011.
  2. K. Kimmig, K. Henneberger, M. Ehrlich, G. Rathke and J. Martin, "Success with efficiency and comfort - The dry double clutch has become established on the automatic transmission market",The 9th Schaeffler Symposium, Detroit, Michigan, pp. 154-163, 2010.
  3. C. Breitfeld, S. Rinderknecht, F. Munk, D. Schmidt-Troje, C. Gueter, J. Neuner and J. Eder, "The New BMW Dual Clutch Transmission", ATZ, Vol. 110, No. 4, 2008.
  4. P. Aversa and E. DeVincent, "Evolution and outlook: powershift DCT250", Getrag Co., DTF 2010-09-16, 2010 (http://www.getlag.com/media/0000001557.pdf).
  5. J. C. Wheals, J. McMicking, S. Shepherd and B. Bonnet, "Proven High Efficiency Actuation and Clutch Technologies for eAMT$^{TM}$ and eDCT$^{TM}$", SAE International J, 2009-01-0513, 2009. https://doi.org/10.4271/2009-01-0513
  6. M. X. Wu, J. W. Zhang and C. S. Ni, "Research on optimal control for dry dual-clutch engagement during launch", Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Vol. 224 No.6, pp.749-763, 2010. https://doi.org/10.1243/09544070JAUTO1341
  7. G. Chen, K. Baldwin and E. Czarnecki, "Real time virtual temperature sensor for transmission clutches", SAE International J. Engines, Vol. 4, No.1, pp.1523-1535, 2011. https://doi.org/10.4271/2011-01-1230
  8. G. Chen, H. Dourraand D. Shah, "Rotating Clutch Temperature Model Development Using Rapid Prototype Controllers", SAE International J. Passenger Cars 2012-01-0625, 2012. https://doi.org/10.4271/2012-01-0625
  9. M. Velardocchia, F. Amisano and R. Flora, "A linear thermal model for an automotive clutch", SAE Technical Paper2000-01-0834, 2000.
  10. G. Kong and Z. Zaimin, "AMT starting process analysis and clutch thermal balance estimation model",International Conference on Electric Information and Control Engineering (ICEICE), Wuhan, China, pp. 2945-2949, 2011.
  11. J. H. Cho and J. W. Kang, The device and method to measure the temperature of clutch component (in Korean), Korean Patent 10-2013-0061394, 2013.
  12. PIAnO (Process Integration, Automation and Optimization) User's Manual (Ver. 3.3), PIPTECH Inc. 2011.
  13. K. W. Park and S. J. Moon, "Optimal design of heat exchangers using the progressive quadratic response surface model", International Journal of Heat and Mass Transfer, Vol. 48, No. 11, pp.2126-2139, 2005. https://doi.org/10.1016/j.ijheatmasstransfer.2004.12.023
  14. H. Matija, H. Zvonko, N. Kranjcevic and J. Deur, "Experimental characterization and modeling of dry dual clutch thermal expansion effects", SAE International Journal of Passenger Cars - Mechanical System, Vol. 6, No. 2, pp.775-785, 2013. https://doi.org/10.4271/2013-01-0818

Cited by

  1. Research on temperature estimation of smart clutch for vehicle vol.1074, pp.1742-6596, 2018, https://doi.org/10.1088/1742-6596/1074/1/012022
  2. Thermal Compensation Control Strategy in Automated Dry Clutch Engagement Dynamics and Launch Manoeuvre vol.20, pp.6, 2015, https://doi.org/10.1007/s12239-019-0102-z