• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.8-16
• /
• 1999

In this paper, the performance of a hybrid DS/SFH-SS(direct-sequence/slow-frequency-hopped spread-spectrum) system with coherent BPSK modulation over Nakagami fading channel in the presence of multiple tone jamming is analyzed. Because the Nakagami m-distribution can describe not only Rayleigh fading but also more general fluctuations involving a specular component by adjusting the value of the fading index m. It is known that for m=1 corresponds to Rayleigh fading, for $1/2{\le}m{\le}1$ corresponds to the worst case fading condition, for m>1 corresponds to Rician fading, and for $m{\to}{\infty}$ corresponds to the nonfading condition. The bit error probability is derived over Nakagami model and numerical evaluations are presented for some combinations of system parameters. The results show that as m increases, the bit error probability is better. Also, at a low JSR(jamming-to-signal power ratio), a pure DS-SS system can achieve lower bit error probability than a hybrid DS/SFH-SS system. But at a high JSR, a hybrid DS/SFH-SS system is shown to be superior to a pure DS-SS system. Therefore, it is demonstrated that without increasing the total system bandwidth, the performance of a hybrid DS/SFH-SS is superior to that of a pure DS-SS system in the presence of multiple tone jamming.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.6
• /
• pp.25-35
• /
• 1998

The control system architecture in switching systems have undergone numerous changes to provide various call processing capability needed in telecommunication services. During call processing in a distributed switching control environment, the delay effect due to communication among main processors or peripheral controllers is one of the limiting factors which affect the system performance. In this paper, we propose a performance model for an IPC(Inter Processor Communication) interface hardware block which is required on the ATM cell-based message processing in a distributed ATM exchange system, and analyze the primary causes which affect the processor performance through the simulation. Consequently, It can be shown that the local CPU of the several components(resources) related to the IPC scheme is a bottleneck factor in achieving the maximum system performance from the simulation results, such as the utilization of each processing component according to the change of the input message rate, and the queue length and processing delay according to input message rate. And we also give some useful results such as the maximum message processing capacity according to the change of the performance of local CPU, and the local CPU maximum throughput according to the change of average message length, which is applicable as a reference data for the improvement or expansion of the ATM control system.

• Journal of the Korean Dietetic Association
• /
• v.4 no.2
• /
• pp.235-244
• /
• 1998

Hand washing is an important component of hygiene program for food handlers. Hands can be a source of direct or indirect contamination of foods with pathogenic microorganisms. In this study, the effectiveness of hand washing methods and the use of 70% alcohol solution against transient skin bacteria was tested in an university foodservice facility. 70% alcohol solution is sprayed for 5 seconds automatically when hands are placed in the dispenser. Samples were taken using swab technique in meat cutting area, vegetable trimming area, and vegetable cutting area: before and after washing hands according to planned methods, and after being sprayed with 70% alcohol solution after washing hands. The bacteriological analysis of total plate counts, coliform, fecal coliform of food handlers' hands was done. Statistical data analysis was completed with Mann-Whitney U test and Kruskal-Wallis model using the SPSS program. The levels of initial contamination of workers' hand were significantly different by the work areas($x^2$=9.156, p<0.01). Workers in the vegetable trimming area had more heavily soiled hands than in the other work areas. Mean of TPC counts and coliform was 8.97×$10^5$ CFU/12.4$cm^2$, 2.93×$10^2$ MPN/12.4$cm^2$ respectively, but fecal coliform was not detected. Transient bacteria were removed from hands after washing and using 70% alcohol solution but were not removed completely. Mean reduction percentage in TPC varied among work areas and ranged from 93.19% to 94.99%, and in coliforms from 97.31% to 100%. A significant difference in TPC was found between before and after hand disinfection (Z=-2.714, p<.01) and between standardized hand washing procedures and un-standardized hand washing procedures(z=-2.301, p<.01). Subjects using the hand sanitizer showed a great elimination of TPC(99.45% reduction), but this effect was valid only after following proper washing procedures. Based on the results, the most effective hand washing method was recommended as the combination of the standardized hand washing procedure with warm-water and use of the 70% alcohol solution. The results can be used to develop hand hygiene programs and training strategies for enhancing hand hygiene practices for food handlers in foodservice operations.

• Journal of Digital Convergence
• /
• v.15 no.8
• /
• pp.333-340
• /
• 2017

Timelapse is an imaging technique that captures motion at regular intervals and then projects it at normal speed. We looked at Timelapse advertising images of global brands and presented a model for analyzing components and expression methods of Timelapse, a new image technique. In previous research, literature research, Internet data survey, and YouTube data were investigated. Continuous photography has been developed as an imaging technique, and we have examined the current production status applied to domestic and foreign documentary, domestic and foreign drama, film, and advertisement. In 2015-2016, I will analyze the techniques of iPhones (2016), Ralph Lauren Polo Ads (2015), and Canon EOS (2013) videos that use Timelapse techniques in their recent advertisements. The results show that the Timelapse component is a static element, the static motif is mainly an artificial structure, the place is outdoor, the color is taken at a time showing the characteristics of the place, and the layout is all centered. The dynamic motif is a moving object. The dynamic line consists of a story based on the object. The time is about 11-15 seconds, the longest is about 1 minute and 30 seconds, and the editing is mainly focused on the product with the brand logo emphasized. In conclusion, it is the role of the image to pay attention to the advertisement and catch the eye. In order to motivate the buyer's mind, it is necessary to direct and edit such as Timelapse, which stimulates the emotions inherent in the mind and stimulates the non-verbal symbols. Future research is likely to reveal various attempts at temporal editing of images.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.6 no.1
• /
• pp.45-50
• /
• 2012

Thoracolumbar orthosis has been used for the rehabilitation of the patients with senile kyphosis. Recently, a number of different thoracolumbar orthosis designs have been introduced but its biomechanical effectiveness still remain unknown. In this study, we compared the pressure distribution on the surface of the trunk and stresses on the orthosis in relation to changes in connecting frame designs (Type 1, one-connecting frame type; Type 2, two-connecting frame type; Type 3, all-in-one type) using finite element (FE) models under different motions of the trunk. The results showed that Type 3 distributed the pressure on the trunk most evenly followed by Type 2 and Type 1 and the difference between Type 1 and Type 2 was negligible. ROM was limited most effectively by Type 3 ($8.5{\sim}9.4^{\circ}$), followed by Type 2 ($11.3{\sim}13.9^{\circ}$) and Type 1 ($12.1{\sim}15.4^{\circ}$). The ratio between the peak von Mises stress and yield strength of each material remained less than 20% regardless of orthosis type indicating low likelihood of component failure. In conclusion, our study found that all-in-one type of orthosis was the most effective design for the conservative treatment of spinal deformity in terms of function and comfort.

• Journal of the Korean Society of Radiology
• /
• v.12 no.1
• /
• pp.115-122
• /
• 2018

The success of the total hip arthroplasty is revealed as initial stability, range of motion, and long term pain, etc. Depending upon choice of implantation options such as femoral neck offset, diameter of the femoral head, the lateral opening tilt. Especially the impingement between femoral head component and acetabular cup limits the range of motion of the hip. In this sense, estimation or evaluation of the range of motion before and after the total hip arthroplasty is important. This study provides the details of a computer simulation technique for the hip range of motion of intact hip as well as arthroplasty. The suggested method defines the hip rotation center and rotation axes for flexion and abduction, respectively. The simulation uses CT-based reconstructed 3D models and an STL treating software. The abduction angle of the hip is defined as the superolateral rotation angle from sagittal plane. The flexion angle of the hip is defined as the superoanterior angle from the coronal plane. The maximum abduction angle is found as the maximum rotation angle by which the femoral head can rotate superolaterally about the anterior-posterior axis without impingement. The maximum flexion angle is found as the maximum rotation angle by which the femoral head can rotate superoanteriorly about the medial-lateral axis without impingement. Compared to the normal hip, the total hip replacement hip showed decreased abduction by 60 degrees and decreased flexion by 4 degrees. This measured value implies that the proposed measurement technique can make surgeons find a modification of increase in the femoral neck offset or femoral head, to secure larger range of motion.

• Korean Journal of Social Welfare
• /
• v.59 no.2
• /
• pp.65-88
• /
• 2007

This study evaluates psychometric properties of the Revised Memory and Behavioral Problems Checklist(RMBPC) in Korean version. The sample includes 387 South Korean family caregivers who provide the majority of day to day tasks and emotional care for their older family members with physical and/or cognitive disabilities. The psychometric properties of the RMBPC are verified by item analysis, exploratory factor analysis(EFA) & confirmatory factor analysis(CFA). For cross-validity, the randomly divided two samples are used: one sample for EFA(n=193, 387/2) and the other sample for CFA(n=194, 387/2). The internal consistency of the K-RMBPC is excellent, and the convergent and criterion-related validity of the K-RMBPC with related variables is empirically confirmed. An EFA based on the Principal Component Analysis(PCA) method with varimax rotation explains 65.85% of variance accounted for by the three factors. A CFA also verifies that the model fit was acceptable. The shorter Korean version of the RMBPC is found reliable and valid. The translated checklist would be very useful for clinical and research settings by (a) focusing on observable, conceptually relevant, potentially modifiable behaviors and (b) using objective criteria within a self-administered framework, to enable clinicians and researchers to pinpoint areas of disturbance and target intervention goals for patients and caregivers in a cost-effective manner.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.sup3
• /
• pp.323-335
• /
• 2016

Breast cancer risk assessment has developed during years and evaluation of genetic factor affecting risk of breast cancer is an important component of this risk assessment. The aim of this meta-analysis was to investigate the role of XRCC1 polymorphisms (Arg194Trp, Arg280His and Arg399Gln) in risk of breast cancer among different population and categories of menopausal status.PubMed, Medline, Web of Science, and PubMed Central were systematically searched to identify studies evaluating association between breast cancer and XRCC1 gene polymorphisms (Arg194Trp, Arg280His and Arg399Gln). Two authors independently extracted required information. Odds Ratios were pooled for four genetic inheritance models using both fixed and the DerSimonian and Laird random-effect models. Egger's test and contour-enhanced funnel plot was used to evaluate publication bias and small study effect. Additional subgroup analysis was performed for menopausal status, ethnicity, and source of controls. After evaluation and applying inclusion criteria on extracted studies, fifty three studies were included in this meta-analysis. For polymorphisms of Arg194Trp and Arg280His, no significant association was observed in all genetic models. Arg194Trp had a protective effect in post-menopausal status only in homozygote model (OR=0.57 [0.37-0.88]). Arg399Gln showed significant association with breast cancer in homozygote (OR=1.21 [1.10-1.34]), dominant (OR=1.09 [1.03-1.15]) and recessive (OR=1.21 [1.09- 1.35]) genetic models. Arg399Gln was associated with higher risk in post-menopausal status for homozygote and heterozygote models. Our findings suggest that XRCC1 gene polymorphisms modify breast cancer risk in different populations and different categories of menopausal status.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.5
• /
• pp.1025-1037
• /
• 2015

Flexible base isolation bearings that separate superstructure from ground have been widely used in the construction field because they make a significant contribution to increasing the fundamental period of the structure, thereby decreasing response acceleration transmitted into the superstructure. However, the established bearing devices installed to uphold the whole building give rise to some problems involved with failure and collapse due to lack of the capacity as modern structures are getting more massive and higher. Therefore, this study suggests new isolation bearings assembled with additional restrainers enabled to reinforcing and recentering, and then evaluates their performance to withstand the seismic load. The superelastic shape memory alloy (SMA) bars are installed into the conventional lead-rubber bearing (LRB) devices in order to provide recentering forces. These new systems are modeled as component spring models for the purpose of conducting nonlinear dynamic analyses with near fault ground motion data. The LRB devices with steel bars are also designed and analyzed to compare their responses with those of new systems. After numerical analyses, ultimate strength, maximum displacement, permanent deformation, and recentering ratio are compared to each model with an aim to investigate which base isolation models are superior. It can be shown that LRB models with superelastic SMA bars are superior to other models compared to each other in terms of seismic resistance and recentering effect.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.3
• /
• pp.303-321
• /
• 2011

The availability and efficient use of the feed resources in Asia are the primary drivers of performance to maximise productivity from animals. Feed security is fundamental to the management, extent of use, conservation and intensification for productivity enhancement. The awesome reality is that current supplies of animal proteins are inadequate to meet human requirements in the face of rapidly depleting resources: arable land, water, fossil fuels, nitrogenous and other fertilisers, and decreased supplies of cereal grains. The contribution of the ruminant sector lags well behind that of non-ruminant pigs and poultry. It is compelling therefore to shift priority for the development of ruminants (buffaloes, cattle, goats and sheep) in key agro-ecological zones (AEZs), making intensive use of the available biomass from the forage resources, crop residues, agro-industrial by-products (AIBP) and other non-conventional feed resources (NCFR). Definitions are given of successful and failed projects on feed resource use. These were used to analyse 12 case studies, which indicated the value of strong participatory efforts with farmers, empowerment, and the benefits from animals of productivity-enhancing technologies and integrated natural resource management (NRM). However, wider replication and scaling up were inadequate in project formulation, including systems methodologies that promoted technology adoption. There was overwhelming emphasis on component technology applications that were duplicated across countries, often wasteful, the results and relevance of which were not clear. Technology delivery via the traditional model of research-extension linkage was also inadequate, and needs to be expanded to participatory research-extension-farmer linkages to accelerate diffusion of technologies, wider adoption and impacts. Other major limitations concerned with feed resource use are failure to view this issue from a farming systems perspective, strong disciplinary bias, and poor links to real farm situations. It is suggested that improved efficiency in feed resource use and increased productivity from animals in the future needs to be cognisant of nine strategies. These include priorities for feed resource use; promoting intensive use of crop residues; intensification of integrated ruminant-oil palm systems and use of oil palm by-products; priority for urgent, wider technology application, adoption and scaling up; rigorous application of systems methodologies; development of adaptation and mitigation options for the effects of climate change on feed resources; strengthening research-extension-farmer linkages; development of year round feeding systems; and striving for sustainability of integrated farming systems. These strategies together form the challenges for the future.