• 전자공학회논문지 IE
• /
• v.46 no.3
• /
• pp.6-11
• /
• 2009

In this paper, manufactured composite nanofiber by electrospinning that make spinning solvent according to weight of PAN/PVdF. PVdF content of composite nanofiber decreases, diameter of fiber decreased. Result that measure contact angle to confirm hydrophile property of PAN/PVdF composite nanofiber, PVdF content increases, could confirm that contact angle with water increases. After leave filter measurement sample for 25 hours in temperature of $40^{\circ}C$, humidity of 85%, result PAN/PVdF composite nanofiber that estimate efficiency could confirm that display performance of HEPA more than 99.95% and ULPA more than 99.999%. And fiber diameter is small, could confirm that filter performance increases. Tensile strength of bulk of PAN/PVdF composite nanofiber was 5-8MPa, expansion 100-300%. And strength and expansion could know that increase according as PVdF's content increases. Tensile strength was 3-8MPa degree after annealing PAN/PVdF composite nanofiber during 2 hours in 120t. Tensile strength was no change almost by annealing, and expansion could know that decrease.

• The Journal of Korean Academy of Sensory Integration
• /
• v.7 no.2
• /
• pp.37-47
• /
• 2009

Objective : The aim of this study is to verify the effects of group sensory integrative intervention on praxis and socialization for school-aged children with sensory integration disorder. Method : The subjects are five children aged between 7 and 13 with sensory integration disorder. All children had participated in 26 sessions of group sensory integrative intervention. The Bruininks-Oseretasky Test of Motor Proficiency(BOT-2) and The Scale for Basic Socialized Function were used so as to evaluate the praxis and socialization. One group pretest-posttest design was used to verify the effect of group sensory integration(SI) intervention. The statistical difference between before and after the group SI intervention in the BOT-2, Scale for basic socialized function is tested by the Wilcoxon matched-pairs signed ranks test. Results : There is a significant difference in BOT-2(Z=-2.023, p=.043) and Scale for basic socialized function(Z=-2.023, p=.043) scores comparing pre-intervention with post-intervention. Conclusions : The results of this study showed that the group sensory integration intervention is effective in improving the praxis and socialization for school-aged children. However, it is difficult to generalize the conclusion because the number of subjects was limited and the environmental confounding factors had not been considered. Therefore, in the future research, it should supplement the aspect these limitations before applying the sensory integration intervention in order to suggest standard criteria for norm data.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.2
• /
• pp.117-122
• /
• 2016

Purpose: Gingival whitening is one of dental treatment purposes which is close to treating aesthetic disorders. Initial gingival whitening treatment was done by dermabrasion using a high power Diode Laser. However, this treatment method cannot be free from any infection or pain after the treatment. Therefore, we have decided to progress gingival whitening treatment using a low power LED laser. Materials and Methods: The laser was irradiated on pork meat then the safety of output power, temperature change and skin denaturalization was measured. Bison 365 nm LED laser was irradiated on oral mucosal pigment of a 15 - 20 kg beagle for 15 min for 1 - 2 weeks, one or two times each. Any pigment loss was checked through Hematoxyline-Eosin staining. Results: The melanin pigments at the area of 365 nm LED Laser irradiation were decreased. Conclusion: The 365 nm LED Laser proposed in this study is considered to compensate the bleaching effect achieved by either using Diode laser or surgical methods.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.6
• /
• pp.2596-2603
• /
• 2013

The precision and endurance of tire mold are very important factors to decide the quality of tire. However, the investigation on the thermal deformation of tire mold has a lot of trouble because the tire mold is produced in airtight permanent casting material. In this study, the thermal deformations such as temperature, displacement and stress distributions inside the AC7A tire mold casting material were analyzed by numerical analysis according to the preheating temperature of permanent casting device. In order to verify the results of numerical analysis, the experiments for temperature measurement of the AC7A casting material were carried out under the same condition with numerical analysis. For the numerical analysis, "COMSOL Multiphysics" was used. The preheating temperatures were set up $150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$ and $300^{\circ}C$, respectively. The thermal deformations were calculated in each case. When the preheating temperature is $300^{\circ}C$, displacement and stress are the lowest with 0.25mm and 0.351GPa, but the temperature is the highest with $374.27^{\circ}C$. When the experimental results were compared with the numerical results, there were some temperature differences because of the latent heat by phase change heat transfer. However, the cooling patterns were almost similar except for the latent heat section.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.12
• /
• pp.1262-1267
• /
• 2008

Reductive discolorization studies were conducted. Azo-dyes usually have biological toxicity and it is known that the dyes are hardly removed by biological treatments. One of the simplest way to remove the color is to break the azo-bond and it is possible to break the bond with zero-valent metals. Three types of azo-dyes (Cibacron Briliant Yellow 3G-P (CBY3G-P), Benzopurpurin 4b (B-4B), Chicago sky blue 6b (CSB6B)) were tested. All tested azo-dyes were highly pH dependent and lower pH was preferred. The reaction mechanism was reductive cleavage and amines were expected as products. The dissolved iron ions from zero-valent iron can also remove the color through coagulation and precipitation and a set of experiments were conducted to evaluate the contribution by the dissolved iron. The results indicated that the contribution were also dependent on the type of dyes. This study showed that the reductive cleavage using zero-valent iron could be an alternative for the azo-dye waste water.

• Journal of Korean Society for Geospatial Information Science
• /
• v.23 no.3
• /
• pp.31-39
• /
• 2015

This paper presents the static and kinematic positioning accuracy by the real-time GPS positioning modes of the low-cost GPS receivers using NTRIP-based augmentation service. For this, acquires both the raw measurements data of the field tests by LEA 6T GPS module of u-blox AG, and correction communication via NTRIP caster with RTKLIB as an open source program for GNSS solution. With computing the positions of the check points and road tracks by six kinds of GPS positioning modes which are Single, SBAS, DGPS, PPP, RTK, and TCP/IP_RTK, compared these results to the reference position of the check points. The position error average and rmse of the static test by GPS L1 RTK surveying showed $N=0.002m{\pm}0.001m$, $E=0.004m{\pm}0.001m$ in horizontal plane, and $h=-0.116m{\pm}0.003m$ in vertical, these results are very closed to the coordinates with the geodetic receiver. Especially, in case of the kinematic test with obstacles located on both sides of road, the computed track with ambiguity fixing showed very similar trajectory considerably from VRS network RTK mode. And also, evaluate and verify the performance of the TCP/IP_RTK mode developed based on TCP/IP protocol.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.709-716
• /
• 2016

Recently, the operating conditions of the various mechanical structures have become more severe and the running time has become longer as the development of plant equipment increases with the introduction of high technology. Thus, the reliability of the system and its accessories is becoming a problem. Normally, synthetic natural gas (SNG) plants use 1.25Cr-0.5Mo or 2.25Cr-1Mo heat resistant steel according to the operating conditions. In this study, a lab-scale reactor was set up using 1.25Cr-0.5Mo steel, in order to carry out corrosion tests for producing synthetic natural gas. The corrosive characteristics were investigated under 1st-methanator operating conditions and fundamental data about the durability and reliability were obtained by using the experimental test. The analysis of results obtained on the durability of the reactor under emission and injection compositions showed that the hydrogen embrittlement caused by hydrogen and the oxidation corrosion caused by H2O had the most effect on the durability of 1.25Cr-0.5Mo steel in the SNG reactor. However, the hydrogen embrittlement and oxidation corrosion occurred simultaneously under emission conditions, so that the corrosion of the material increased suddenly after a long operating time. Besides, the corrosion of the 1.25Cr-0.5Mo steel under the injection composition was faster than that under the emission composition.

• Information Systems Review
• /
• v.21 no.1
• /
• pp.23-38
• /
• 2019

The social network service (SNS) is one of the important marketing channels, so many companies actively exploit SNSs by posting SNS messages with appropriate content and style for their customers. In this paper, we focused on the psychological distances embedded in the SNS messages and developed a method to measure the psychological distance in SNS message by mixing a traditional content analysis, natural language processing (NLP), and machine learning. Through a traditional content analysis by human coding, the psychological distance was extracted from the SNS message, and these coding results were used for input data for NLP and machine learning. With NLP, word embedding was executed and Bag of Word was created. The Support Vector Machine, one of machine learning techniques was performed to train and test the psychological distance in SNS message. As a result, sensitivity and precision of SVM prediction were significantly low because of the extreme skewness of dataset. We improved the performance of SVM by balancing the ratio of data by upsampling technique and using data coded with the same value in first content analysis. All performance index was more than 70%, which showed that psychological distance can be measured well.

• Research in Plant Disease
• /
• v.23 no.4
• /
• pp.322-333
• /
• 2017

In June and July 2015 and 2017, typical signs and symptoms of brown rot were observed on the fruit of Japanese apricot, peach, apricot, Japanese plum, and sweet cherry with incidence levels of 2-5% in Jeonju and Imsil, Korea. Early symptoms were small, circular, light brown spots that eventually destroyed entire fruit. Small sporodochia later appeared on the surface. Conidia isolated from each host were one-celled, hyaline, lemon-shaped and borne in branched monilioid chains. The optimal temperature range for hyphal growth of all the isolates was $20-25^{\circ}C$. The growth of hyphae was faster on potato dextrose agar and oatmeal agar than others. Multiple alignments using the ITS sequences from different host showed that they matched each other (100%). The ITS sequences showed 100% identity to those of M. fructicola. Based on the morphological characteristics and phylogenetic analysis via internal transcribed spacer (ITS), all the isolate was identified as M. fructicola. Pathogenicity of representative isolates was proved by artificial inoculation, fulfilling Koch's postulates. This is the first confirmed report on brown rot caused by M. fructicola on stone fruit in Korea.

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.1
• /
• pp.27-31
• /
• 2010

The purpose of this study was to investigated the usefulness of MR perfusion image comparing with SPECT image. A total of pediatric 30 patients(average age : 7.8) with Moyamoya disease were performed MR Perfusion with 32 channel body coil at 3T from March 01, 2010 to June 10, 2010. The MRI sequences and parameters were as followed : gradient Echo-planar imaging(EPI), TR/TE : 2000ms/50ms, FA : $90^{\circ}$, FOV : $240{\times}240$, Matrix : $128{\times}128$, Thickness : 5mm, Gap : 1.5mm. Images were obtained contrast agent administrated at a rate of 1mL/sec after scan start 10s with a total of slice 1000 images(50 phase/1 slice). It was measured with visual color image and digitize data using MRDx software(IDL version 6.2) and also, it was compared of measurement with values of normal and abnormal ratio to analyze hemodynamic change, and a comparison between perfusion MR with technique using Warm Color at SPECT examination. On MR perfusion examination, the color images from abnormal region to the red collar with rCBV(relative cerebral blood volume) and rCBF(relative cerebral blood flow) caused by increase cerebral blood flow with brain vascular occlusion in surrounding collateral circulation advancement, the blood speed relatively was depicted slowly with blue in MTT(Mean Transit Time) and TTP(Time to Peak) images. The region which was visible abnormally from MR perfusion examination visually were detected as comparison with the same SPECT examination region, would be able to confirm the identical results in MMD(Moyamoya disease)judgments. Hymo-dynamic change in MR perfusion examination produced by increase and delay cerebral blood flow. This change with digitize data and being color imaging makes enable to distinguish between normal and abnormal area. Relatively, MR perfusion examination compared with SPECT examination could bring an excellent image with spatial resolution without radiation expose.