• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.42-46
• /
• 2016

Hydrogen assisted cracking (HAC) is one of the most complicated problem in welding. Huge amount of studies have been done for decades. Based on them, various standards have been established to avoid HAC. But it is still a chronic problem in industrial field. It is well known that the main causes of the hydrogen crack are residual stress, crack susceptible micro structures and a certain critical level of hydrogen concentration. Even though the exact generating mechanism is unclear till today, it has been reported that the hydrogen level in the weld metal should be managed less than a certain amount to prevent it. Matsuda studied that the residual hydrogen level in the weld metal can be varied even if the initial hydrogen content is same. It is also insisted in this report that the residual hydrogen concentration is in stronger correlation with hydrogen crack than the initial hydrogen content. But, in practical point of view, the residual hydrogen is still hard to consider because measuring hydrogen level is time and cost consuming process. In this regard, numerical analysis is the only solution for considering the residual hydrogen content. Meanwhile, Takahashi showed the possibility of predicting the residual hydrogen by a rigorous FE analysis. But, few commercial software suitable for solving the weld metal hydrogen has been reported yet. In this study, two dimensional thermal - hydrogen coupled analysis was developed by using the commercial FE software MARC. Since the governing equation of the hydrogen diffusion is similar to the heat transfer, it is shown that the heat transfer FE analysis in association with hydrogen diffusion property can be used for hydrogen diffusion analysis. A series of simulation was performed to verify the accuracy of the model. For BOP (Bead-On-Plate) and the multi-pass butt welding simulations, remaining hydrogen contents in the weld metal is well matched with measurements which are referred from Kim and Masamitsu.

• Journal of Haehwa Medicine
• /
• v.16 no.2
• /
• pp.109-119
• /
• 2007

Xu-lao(虛勞) is deficient disease which is weak body and spirit. It occurs many symptoms, for example lack of appetite, dizziness, involuntary emission of semen, wet dream, back and chest pain, night sweat, cough and so on. In oriental medicine, xu-lao(虛勞) is well-known disease and can be treated easily. In general, xu-lao (虛勞) patiences like to be treated by oriental medical doctors. In spite of improving food, house and clothes, xu-lao(虛勞) is on the increase by fatty foods and stress. In most of these cases, the cooperations of heart and kidney are hurted. On Fang-you-ge-bian(脈證方藥合編) which is the famous prescription book in Korea, gu-an-xin-shen-wan(古庵心腎丸) and Jiu-yuan-xin-shen-wan(究原心腎丸) are used well and have good effects in these cases. Gu-an-xin-shen-wan(古庵心腎丸) can treat white hair, palpitation, involuntary emission of semen, amblyopia, buzzing in the ears, backache and so on. Jiu-yuan-xin-shen-wan(究原心腎丸) can treat lack of appetite, dizziness, involuntary emission of semen, wet dream, back and chest pain, diseased sweat, cough, coldness of hands and feet, and so on. The symptoms of Gu-an-xin-shen-wan(古庵心腎丸) are similar with those of Jiu-yuan-xin-shen-wan(究原心腎丸). But, it is very important that Gu-an-xin-shen-wan(古庵心腎丸) can be used in cases of hot deficient disease but Jiu-yuan-xin-shen-wan(究原心腎丸) can be used in cases of cold deficient disease.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.49 no.2
• /
• pp.148-153
• /
• 2004

The Hessian fly, Mayetiola destructor (Say), is known to be one of the major insect herbivores of wheat worldwide. In order to provide molecular events on interactions of the NIL with H21 and larvae of Hessian fly biotype L, the TaCR1 gene, Triticum aestivum cytokinin repressed 1, was isolated through the suppression subtractive hybridization, which was constructed using stems of the NIL with H21 at 6 days after infestation as tester and stems of the recurrent parent Coker797 without H21 at 6 days after infestation as driver. Transcript levels of TaCR1 mRNA in the NIL with H21 were highest at 6 days after infestation but in the Coker797 without H21 until 8 days were similar with those of non-infested plants. Expression of the TaCR1 gene was decreased at early time and then recovered after wounding or $H_2O$$_2$ treatment as well as 6-BAP treatment. Transcripts levels of the TaCR1 gene was changed after MeJA, SA, ethephone, or ABA treatment. In drought treatment, the TaCRl gene were increased at early stage of stress and then decreased at late stage. Expression of the TaCRl gene was continued to decrease through 24 h in the cold treatment. Although the TaCRl gene is increased through infestation in NIL with H21, further study was required to elucidate a role on resistance against larvae of Hessian fly. However, the TaCR1 gene could be used as marker gene on response of plants against abiotic stresses as well as application of plants with several hormones.

• Korean Journal of Environmental Agriculture
• /
• v.34 no.3
• /
• pp.210-216
• /
• 2015

BACKGROUND: In korea, sweet persimmon(Diospyros kaki) cultivation is front to abiotic stresses such as frost damage at fruit maturing stage. The cold and rapid freezing stresses are most damaging to fruit production which is most actively progressed in late fall. This study was performed to evaluate the validity of chlorophyll fluorescence imaging(CFI) technology to determine the degree of frost damage in sweet persimmon fruits. METHODS AND RESULTS: The sweet persimmon fruits were measured separately for each treatment(15, 30, 60 minutes) at 24 hours after treatment(HAT) rapid freezing. A CFI FluorCam (FC 1000-H, PSI, Czech Republic) was used to measure the fluorescence images of the fruits. In rapid freezing for 15 minutes, photochemical parameters were not changed. However, in rapid freezing for 30 and 60 minutes, photochemical parameters were lowered. Especially, $F_m$, $F_v$, $F_v/F_m$ and ${\Phi}PSII$ values were declined under rapid freezing. CONCLUSION: In our study, it was clearly indicated that the rapid freezing could be a stress in sweet persimmon fruits. The CFI analysis and its related parameters are applicable as a rapid assessing technique for the determination of frost damage.

• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.434-442
• /
• 2010

This study was carried out to determine necessary conditions for optimal ventilation of small windowless piglet house (4.0 (W) $\times$ 11.0 (L) $\times$ 2.6(H) m) with corridor and attic for preheating using CFD (Computational Fluid Dynamics) simulation. The experimental weaning piglet house was consisted of a corridor, an attic, 4 rooms (3.0 (W) $\times$ 2.75(L) m), 3 fences (0.7(H) m), 5 air inlets and 2 exhaust fans (0.4 (D) m) and simulated using CFD code, FLUENT. The simulation results for the experimental weaning piglet house showed that each room was uniformly ventilated under all the experimental conditions and air velocities at 0.1 m above floor are less than 0.15 m/s for 0.75 m/s and 1.0 m/s of air inlet velocity but 0.61 m/s for 1.25 m/s. The simulation results are similar to the measured results. Considering the air flow pattern, ventilating efficiency, air velocity at 0.1 m above floor and cold stress of weaning piglets and so on, the optimum velocity of air inlet might be 1.0 m/s.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.166-177
• /
• 1993

Bending fatigue strength tests were made for VC coated die steels which were coated by immersing in a molten borax bath and for hardened die steels which were quenched and tempered, in order to clarify the effect of VC coating at $1000^{\circ}C$ and $1025^{\circ}C$. The material used in this investigation was a representative cold and hot die steels STD11, STD61. The results obtained are as follows. 1) The endurance limit of VC coated die steels was a little lower than that of hardened die steels. It is considered to be mainly due to the decfl.lase of hardness in the substrates. Accordingly, the endurance limit reo covered almost to the level of hardened die steels by an additional diffusion treatment. 2) The initiation point of fatigue fracture of VC coated die steels in reversed bening was on the substrate just under the VC layer. Hence, the endurance limit is corrected to the hardness of this part. 3) But, there is a considerable scatter in this relationship and the endurance limit of VC coated die steels was a little lower than that of hardened die steels with equal hardness. These results suggest that the fatigue strength of VC coated die steels is determined not only by the hardness but also by other factors. For example. the residual stress in the substrate just under VC coating layer is one of the factors besides hardness which is mainly related to the retained austenite(${\gamma}_R$).

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.1
• /
• pp.10-19
• /
• 1997

This study has been conducted to investigate the effects of initial structure on the microstructure and tensile properties of high strength trip steel sheet. The initial structure before austempering remarkably influenced the second phase. The specimen with normalized initial structure showed mainly bainitic ferrite and retained austenite, while the as rolled specimen and spherodized specimen showed martensite plus retained austenite and martensite plus bainitic ferrite with small retained austenite, respectively. Two type of retained austenite, film type and granual type were observed in all specimens. The as rolled specimen appeared the highest contents of retained austenite owing to the compressive stress by cold rolling. The contents of retained austenite increased with increasing intercritical annealing temperature and austempering time. Tensile strength showed the highest in the as rolled specimen, while the highest elongation were obtained in the normalized specimen. The maximum T.S.${\times}$El. Value showed in normalized initial structure and increased with increasing intercritical annealing and austempering time. The highest Value of T.S.${\times}$El. obtained at austempering temperature of $400^{\circ}C$ and retained austenite of 12%.

• Corrosion Science and Technology
• /
• v.18 no.1
• /
• pp.1-7
• /
• 2019

To find proper lathe machining parameters for SA182 Grade 304 stainless steel (SS), six kinds of samples with different machining surface states were prepared using a lathe. Surface morphologies and microstructures of near surface deformed layers on different samples were analysed. Surface morphologies and chemical composition of oxide films formed on different samples in simulated primary water with $100{\mu}g/L\;O_2$ at $310^{\circ}C$ were characterized. Results showed that surface roughness was mainly affected by lathe feed. Surface machining caused grain refinement at the top layer. A severely deformed layer with different thicknesses formed on all samples. In addition to high defect density caused by surface deformation, phase transformation, residual stress, and strain also affected the oxidation behaviour of SA182 Grade 304 SS in the test solution. Machining parameters used for # 4 (feed, 0.15 mm/r; back engagement, 2 mm; cutting speed, 114.86 m/min) and # 6 (feed,0.20 mm/r; back engagement, 1 mm; cutting speed, 73.01 m/min) samples were found to be proper for lathe machining of SA182 Grade 304 SS.

• Korean Journal of Medicinal Crop Science
• /
• v.26 no.6
• /
• pp.447-454
• /
• 2018

Background: The leaf temperature ($T_{LEAF}$) is one of the most important physical parameters governing water and carbon flux, including evapotranspiration, photosynthesis and respiration. Cnidium officinale is one of the important folk medicines for counteracting a variety of diseases, and is particularly used as a traditional medicinal crop in the treatment of female genital inflammatory diseases. In this study, we developed a model to estimate $T_{Leaf}$ of Cnidium officinale Makino based on black globe temperature ($T_{BGT}$). Methods and Results: This study was performed from April to July 2018 in field characterized by a valley and alluvial fan topography. Databases of $T_{LEAF}$ were curated by infrared thermometry, along with meteorological instruments, including a thermometer, a pyranometer, and an anemometer. Linear regression analysis and Student's t-test were performed to evaluate the performance of the model and significance of the parameters. The correlation coefficient between observed $T_{LEAF}$ and calculated $T_{BGT}$ obtained using an equation, developed to predict $T_{LEAF}$ based on $T_{BGT}$ was very high ($r^2=0.9500$, p < 0.0001). There was a positive relationship between $T_{BGT}$ and solar radiation ($r^2=0.8556$, p < 0.0001), but a negative relationship between $T_{BGT}$ and wind speed ($r^2=0.9707$, p < 0.0001). These results imply that heat exchange in leaves seems to be mainly controlled by solar radiation and wind speed. The correlation coefficient between actual and estimated $T_{BGT}$ was 0.9710 (p < 0.0001). Conclusions: The developed model can be used to accurately estimate the $T_{Leaf}$ of Cnidium officinale Makino and has the potential to become a practical alternative to assessing cold and heat stress.

• Design & Manufacturing
• /
• v.12 no.3
• /
• pp.25-30
• /
• 2018

Recently The automotive industry is trying to increase the energy efficiency by reducing the weight of the car body and engine components as a way to achieve high energy efficiency. In particular, the reduction of the weight of the vehicle through the weight reduction of the vehicle body has the advantage that the fuel consumption and the output can be improved. But at the same time, there is the disadvantage that the strength becomes weak due to the reduction of the material thickness. Therefore, in order to overcome these disadvantages, materials with high strength according to the unit thickness have been actively developed, and researches for applying them have also been increasing. In this study, we will investigate the application of cold rolled steel sheet, which is a lightweight material, to a horn bracket that secures a installed in an automobile engine room. The horn bracket secures the horn on the car engine and is bolted to the outer wall of the engine. The momentum is acted on the bracket due to the distance between the bolt fastening part and the car horn installed on the bracket end side. Therefore, the body part of the bracket is more likely to be destroyed by the influence of the continuous stress. In this paper, design optimization for weight reduction and strength enhancement was performed to solve this problem, and possibility of applying the rolled steel sheet material as lightweight material by tensile test and fabrication was confirmed.