• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.333-342
• /
• 2004

Tensile and low cycle fatigue (LCF) tests on prior cold worked 316L stainless steel were carried out at various temperatures from room temperature to 650$^{\circ}C$. At all test temperatures, cold worked material showed the tendency of higher strength and lower ductility compared with those of solution treated material. The embrittlement of material occurred in the temperature region from 300$^{\circ}C$ to 600$^{\circ}C$ due to dynamic strain aging. Following initial cyclic hardening for a few cycles, cycling softening was observed to dominate until failure occurred during LCF deformation, and the cyclic softening behavior strongly depended on temperature and strain amplitude. Non-Masing behavior was observed at all test temperatures and hysteresis energy curve method was employed to describe the stress-strain hysteresis loops at half$.$life. The prediction shows a good agreement with the experimental results.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.388-392
• /
• 2016

A cold roll-bonding process was applied to fabricate an AA1050/AA6061/AA1050 laminate complex sheet. Two AA1050 and one AA6061 sheets of 2 mm thickness, 40 mm width and 300 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 1.2 mm in thickness by conventional rolling. The rolling was performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 5.0 m/sec. The AA1050/AA6061/AA1050 laminate complex sheet fabricated by roll bonding was then hardened by natural aging T4) and artificial aging (T6) treatments. The microstructures of the as-roll bonded and the age hardened Al complex sheets were revealed by optical microscope observation; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the as-roll bonded complex sheet was found to increase by 2.9 times compared to that value of the starting material. In addition, the hardness of the complex sheets increased with cold rolling for AA1050 and age-hardening treatment for AA6061, respectively. After heat treatment, both AA1050 and AA6061 showed typical recrystallization structures in which the grains were equiaxed; however, the grain size was smaller in AA6061 than in AA1050.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.120-123
• /
• 2007

The effects of annealing condition on the occurrence of the delamination in cold drawn hyper-eutectoid steel wires, were investigated. Annealing treatment was performed on cold drawn steel wires for temperature range of $425^{\circ}C\sim500^{\circ}C$ with the variation of annealing time from 30sec to 15min. The increase of annealing temperature and time would cause the decrease of tensile strength and the increase of ductility. However, the occurrence of the delamination, representing torsional ductility, showed the different way from the variation of ductility.

• Food Science of Animal Resources
• /
• v.21 no.1
• /
• pp.47-55
• /
• 2001

This experiment was conducted to investigate the effects of marbling and maturity on physicochemical properties of Hanwoo meat during cold storage. A total of 18 carcasses were collected by marbling and maturity score at the commercial slaughter house. Loins of carcasses were selected and moved to laboratory and used to measure physico-chemical characteristics during 7 weeks storage at $0^{\circ}C$. The pH of samples was tended to be increased until 3 weeks storage. The water holding capacity of samples was not affected by marbling and maturity score. Lightness value of all samples was not changed, whereas redness value of high marbling samples was significantly(p<0.05) higher than that of low marbling samples. Purge loss of high marbling samples was significantly(p<0.05) lower than that of low marbling samples. These results indicate that high marbling and low maturity has better meat quality than low marbling and high maturity in Hanwoo.

• Journal of Powder Materials
• /
• v.17 no.6
• /
• pp.477-481
• /
• 2010

Cu-Sn based alloys were manufactured by gas atomization spray casting route in order to achieve a fine scale microstructure and a high tensile strength. The spray cast Cu-10Sn-2Ni-0.2Si alloy had an equiaxed grain microstructure, with no formation of brittle ${\delta}-Cu_{41}Sn_{11}$ phase. Aging treatment promoted the precipitation of finely distributed particles corresponding to ${\delta}-Ni_2Si$ intermetallic phase throughout the $\alpha$-(CuSn) matrix. The cold-rolled Cu-Sn-Ni-Si alloy had a very high tensile strength of 1200 MPa and an elongation of 5%. Subsequent aging treatment at $450^{\circ}C$ for 1h slightly reduced the tensile strength to 700 MPa and remarkably increased the elongation up to 30%. This result has been explained by coarsening the precipitates due to over aging and reducing the dislocation density due to annealing effects.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.2
• /
• pp.88-95
• /
• 2022

Titanium alloy for bio-medical applications have been developed to reduce the toxicity of alloying elements and avoid the stress-shielding effect which is caused by relatively high elastic modulus compared to bone. Ti-39Nb-6Zr (TNZ40) alloy of elastic modulus exhibits around 40 GPa in the case of beta single phase. However, the strength of this alloy is lower than the other types of titanium alloys. Many research found that adding oxygen to beta-titanium alloys is beneficial for improving the strength through solid solution strengthening. In this study, TNZ40 ingots with addition of O were prepared by an arc remelting process (Ti-39Nb-6Zr-0.16O (wt.%), Ti-39Nb-6Zr-0.26O (wt.%)). Thermo-mechanical processing (i.e., heat treatment, cold swaging and aging heat treatment) has been performed under various conditions. Therefore, the aim of this study is to investigate the effect of oxygen content and ω phase formation on microstructure and mechanical properties.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.1
• /
• pp.10-16
• /
• 2010

The microstructure of Cu-Mg-P alloy sheet consisted of Cu matrix and very fine MgP precipitate, and it has been observed that the microstructure remains virtually unchanged by Ag additions up to 2%. Ag solutes were dissolved into the matrix and hardly found in the precipitates. The hardness increased with increase of the Ag content, while the conductivity slightly decreased. Strain hardening through cold rolling was found to be effective in improving the hardness, especially in high-Ag alloys. Aging treatment was conducted either before the first cold rolling or between the first and the final cold rolling, and the conductivity was significantly higher at the former case, regardless of the Ag content. Softening of Cu-Mg-P alloy sheet was remarkable above $400^{\circ}C$ and the Ag content did not show any significant effect on it.

• Fashion & Textile Research Journal
• /
• v.10 no.5
• /
• pp.668-675
• /
• 2008

The purpose of this study was to collect data of skin temperature and physiological responses which is useful for standardization of insulation measurement in various garments. And we investigated sex and season difference of physiological responses of 60's males and 60's females in hot and cold environment. Healthy ten 60's males and ten 60's females volunteered as subjects. The experiment was conducted three times; One for winter condition($5^{\circ}C$, 45%), another for summer condition($30^{\circ}C$, 65%) and the other for nude condition as control($30^{\circ}C$, 65%). The subjects were sitting for 1 hour with suitable ensemble on each experimental condition in climate chamber. We measured skin temperature, rectal temperature, heart rate, oxygen uptake, sweat rate, blood flow, blood pressure and subjective sensations. We found that skin temperature and most of physiological responses were higher in male subject, summer condition than in female subject, winter condition.

• Journal of Korea Port Economic Association
• /
• v.34 no.3
• /
• pp.1-16
• /
• 2018

The demand for biopharmaceuticals is on the rise spurred by the fourth industrial revolution and an aging society in Korea. Consequently, the scale of the biopharmaceutical industry is continuously increasing globally, thereby leading to an increase in the distribution of biopharmaceuticals. However, the relative inferiority of the domestic drug distribution structure, when compared to the advanced countries, and strict logistics regulations concerning the handling of biopharmaceuticals have raised the need for systematic management. Essentially, the significance of third-party logistics companies in the cold chain for pharmaceutical cold chain has increased with an intense management environment for pharmaceuticals. The purpose of this study is to investigate the selection factors of drug cold chain's third-party logistics companies and to examine the influence of selection factors on satisfaction. A multiple regression analysis was conducted to investigate how cold chain third-party logistics factors affect the satisfaction of third-party logistics in cold chain. The results of analysis showed that expertise, facility, and linkage are factors affect customer satisfaction. The managerial capacity was derived not as an influential factor. These findings suggest that the future cold chain industry will be equipped to provide direction and strategic implications.