• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.53-58
• /
• 2017

FRP Hybrid Bar, composed of an embedded steel and the coated composites with epoxy and glass fiber, is an effective construction material with tension-hardening performance and lightweight. The epoxy exposed to UV(Ultra Violet Rays) and FT(Freezing and Thawing) action easily shows a surface deterioration, which can cause degradation of bonding strength between inside-steel and outside-concrete. In the present work, surface inspection for 3 different samples of normal steel, FRP Hybrid Bar before UV, and FRP Hybrid Bar after UV test was performed, then concrete samples with 3 reinforcement types were prepared for accelerated FT test. Through visual inspection on 3 typed reinforcement, no significant deterioration like chalking was evaluated. The results from FT test to 120 and 180 cycles showed FRP Hybrid Bar exposed to UV test has higher bonding strength than normal steel by 106.3% due to enlarged bond area by silica coating. The 3 cases showed a similar bond strength tendency with increasing FT cycles, however a relatively big deviations of bond strength were evaluated in FRP Hybrid Bar after UV test due to loss of silica coating.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.9
• /
• pp.644-655
• /
• 2011

VOCs (Volatile Organic Compounds) have adverse effects on human health and have caused serious global air pollution problems such as ozone depletion and cimate changes. The total of 56 target VOCs were selected to be monitored in this study for 4 years (2006~2009). The VOCs were measured every hour. The concentration of BTEX was higher than the other target compounds. Generally, the levels of VOCs measured in this study were higher than those measured by the other studies because Gamjeon and Jangrim monitering sites are located in industrial areas. The seasonal variations showed that the VOCs were the highest in winter. The temporal variations showed that the VOCs were high during commuting time on weekday. PMF model was used to resolve source types and source contributions of VOCs in this study. Identified sources and quantified contributions resolved by PMF were vehicle exhaust (15.22%), thinning solvent (29.83%), surface coating (17.13%), industries (13.95%), LPG vehicle (15.22%), combustion boiler (7.11%) and biogenic source (6.61%). Thinning solvent and Surface coating were the most contributed sources possibly due to manufactures and automobile garages in Gamjeon and solvent and paint manufactures in Sasang-Gu.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.314-319
• /
• 2013

In this study, nitrogen doped $TiO_2$ ($N-TiO_2$) coated on an activated carbon pellet (ACP) was prepared using sol-gel and the solid state heat treatment of urea to improve the removal property of volatile organic compounds (VOCs). To explore the visible light photocatalytic activity of the ACP under the light emitting diods (LED), the removal property of benzene gas was characterized by gas chromatography. The SEM and BET results show that the increment of titanium tetra isopropoxide contents leads to the increased $TiO_2$ coating amount of ACP surface and decreased specific surface area. From the results of benzene gas removal, the breakthrough time of ACP10 increased about 2 times compared to that of the ACP. The improved performance was attributed to the $N-TiO_2$ coating on ACP surface, which could be more effective to remove benzene gas under the condition of LED lamp.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.331-338
• /
• 2008

Coal-tar enamel, blown asphalt and polyethylene have been used as wrapping materials of steel pipe in Korea. Currently, every manufacturer produces wrapped steel pipes with different materials and methods, and little research has been performed to get on wrapping methods and materials. In this research, properties of wrapping material of steel pipe used for water supply have been evaluated. All of the materials tested in this work were found to meet the standard. Among the wrapping materials of steel pipe tested, blown asphalt and coal-tar enamel were reasonable in price, and their mechanical properties were excellent. The quality of the wrapped steel pipes was being melted easily in organic solvent. When coated thick, the load of the steel pipes was higher than necessary. Tensile strength of cathode exfoliation and PE 3-layer wrapping method was excellent. The pulling intensity of T-Die PE 3-layer was stronger than PE fluidized in PE wrapping method. Cathode exfoliation area was smaller than PE fluidized. Mechanical property and thermo-property of T-Die PE 3-layer were excellent and its anti-chemical property was great. Liquid epoxy can change the property of coating materials depending on the hardening condition and resin selection. Polyurethane used in this test showed a less adhesive strength with steel pipes than epoxy. Moisture absorbance rate was higher than Epoxy's, however. To utilize polyurethane as wrapping materials, basic property of the matter should be improved followed by finding the best suited coating condition. The method of PE 3-layer by extrude method appeared to be the best in this study. However, identification of other wrapping materials requires further additional tests.

• Korean Journal of Materials Research
• /
• v.16 no.4
• /
• pp.225-230
• /
• 2006

Nanoimprint lithography (NIL) is a novel method of fabricating nanometer scale patterns. It is a simple process with low cost, high throughput and resolution. NIL creates patterns by mechanical deformation of an imprint resist and physical contact process. The imprint resist is typically a monomer or polymer formulation that is cured by heat or UV light during the imprinting process. Stiction between the resist and the stamp is resulted from this physical contact process. Stiction issue is more important in the stamps including narrow pattern size and wide area. Therefore, the antistiction layer coating is very effective to prevent this problem and ensure successful NIL. In this paper, an antistiction layer was deposited and characterized by PECVD (plasma enhanced chemical vapor deposition) method for metal stamps. Deposition rates of an antistiction layer on Si and Ni substrates were in proportion to deposited time and 3.4 nm/min and 2.5 nm/min, respectively. A 50 nm thick antistiction layer showed 90% relative transmittance at 365 nm wavelength. Contact angle result showed good hydrophobicity over 105 degree. $CF_2$ and $CF_3$ peaks were founded in ATR-FTIR analysis. The thicknesses and the contact angle of a 50 nm thick antistiction film were slightly changed during chemical resistance test using acetone and sulfuric acid. To evaluate the deposited antistiction layer, a 50 nm thick film was coated on a stainless steel stamp made by wet etching process. A PMMA substrate was successfully imprinting without pattern degradations by the stainless steel stamp with an antistiction layer. The test result shows that antistiction layer coating is very effective for NIL.

• Korean Journal of Environmental Agriculture
• /
• v.22 no.2
• /
• pp.124-129
• /
• 2003

The objectives of this study are to manufacture an efficient $TiO_2$, photocatalyst and to delineate optimum operational parameters for TCE (trichloroethylene) degradation in a photocatalytic oxidative reactor. The $TiO_2$ photocatalyst irradiated by 365 nm UV light is expected to increase degradation of TCE in solution by a series of photocatalytic oxidations in the reactor. A new membrane $TiO_2$ photocatalyst wns eventually developed by coating a mixture of Davan-C(0.24 wt%) and PVA(0.16 wt%) on the surface of slips using the slip-casting method. Results show that increase in the number of coating of $TiO_2$ sol on surface of photocatalysts and in the surface thickness improved the endurance and photocatalysts, but these physical modifications caused significant decrease in the overall degradation efficiency of TCE. Pre-aeration or recirculation of the influents to the reactors containing TCE increased degradation efficiency of TCE. The optimum operational conditions far the surface area of photocatalysts and UV light intensity appeared to be $1.47\;mL/cm^2$ and $225\;W/cm^2{\times}100$, respectively, in the reactor. Based on the overall experimental results, the photocatalytic oxidation of TCE with the new membrane $TiO_2$ photocatalyst is found to be very effective under the operational conditions delineated in this study.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.172-177
• /
• 2010

This study reports the high-temperature oxidation kinetics, ASR(area specific resistance), and interfacial microstructure of metallic interconnects coated with conductive oxides in oxidation atmosphere at $800^{\circ}C$, The conductive material LSC($La_{0.8}Sr_{0.2}CoO_3$, prepared by Solid State Reaction) was coated on the Crofer22APU. The contact behavior of coating layer/metal substrate was increased by sandblast. The electrical conductivity of the LSC coated Crpfer22APU was measured by a DC two probe four wire method for 4000hr, in air at $800^{\circ}C$. Microstructure and composition of the coated layer interface were investigated by SEM/EDS. These results show that a coated LSC layer prevents the formation and growth of oxide scale such as $Cr_2O_3$ and enhances the long-term stability and electrical performance of metallic interconnects for SOFCs.

• Archives of Pharmacal Research
• /
• v.20 no.6
• /
• pp.555-559
• /
• 1997

The three different batches of an oral sustained release melatonin (MT) delivery system were prepared by aqueous-based fluid-bed coating of the sugar spheres for the evaluation of in vitro release characteristics and plasma concentration profiles in human subjects. The MT contents in 20% coated sugar spheres of three batches (B1, B2 and B3) were $3.3{\pm}0.08$, $2.4{\pm}0.1$ and $2.5{\pm}0.13$ mg per gram of coated sugar spheres, respectively. The release profiles of three different batches had a very similar fashion. However, the release profiles of three different batches had a very similar fashion. However, the release half-lives $(T_{50%})$ of MT from B1, B2 and B3 was $3.70{\pm}0.2$, $5.2{\pm}0.2$ and $4.9{\pm}0.07h$, respectively. Plasma concentration profiles of sustained release 0.2mg melatonin-loaded sugar spheres containing 10% immediate release melatonin in gelatin capsules (B1 and B2) were then evaluated in human subjects. The in vivo plasma concentration profies of the two batches (B1 and B2) were very similar each other and located between the physiological endogenous ranges. The time to reach the peak concentration $(T_max)$ was more advanced in case of B1 when compared to B2. However, there was no statistically significant difference in the maximum concentration $(C_max)$ and the area under the curve (AUC) between B1 and B2. The AUC of melatonin-loaded sugar spheres containing 10% and 20% immediate release MT in human subjects had a good linearity between dose and AUC, regardless of the fraction of immediate release MT, indicating the first order elimination process of MT within these doses. The current oral sustained release MT delivery system may be utilized to treat circadian rhythm disorders if it is proven to be more clinically useful when compared to immediate release MT.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.268-275
• /
• 2021

The three factors that determine the strength of concrete are the strength of cement paste, aggregate and ITZ(Interfacial Transition Zone) between aggregate and cement paste. Out of these, the strength of ITZ is the most vulnerable. ITZ is formed in 10~50㎛, the ratio of calcium hydroxide is high, and CSH appears low ratio. A high calcium hydroxide ratio causes a decrease in the bond strength of ITZ. ITZ is due to further weak area. The problem of ITZ appears as a more disadvantageous factor when it used lightweight aggregate. The previous study of ITZ properties have measured interfacial toughness, identified influencing factors ITZ, and it progressed SEM and XRD analysis on cement matrix without using coarse aggregates. also it was identified microstructure using EMPA-BSE equipment. However, in previous studies, it is difficult to understand the microstructure and mechanical properties. Therefore, in this study, a method of measuring electrical resistance using EIS(Electrochemical Impedance Spectroscopy) measuring equipment was adopted to identify the ITZ between natural aggregate and lightweight aggregate, and it was tested the change of ITZ by surface coating of lightweight aggregate with ground granulated blast furnace slag. As a result, the compressive strength of natural aggregate and lightweight aggregate appear high strength of natural aggregate with high density, surface coating lightweight aggregate appear strength higher than natural aggregate. The electrical resistivity of ITZ according to the aggregate appeared difference.

• Resources Recycling
• /
• v.30 no.2
• /
• pp.68-74
• /
• 2021

This study investigated formaldehyde (HCHO) removal by preparing porous supports using domestic low-grade silica coated with Co-ZSM5 and Cu-ZSM5 as the catalysts. First, the sample of the raw material for the support contained 90% silica with quartz crystal phase, which was confirmed as low-grade silica. According to Energy-dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FT-IR) analyses, the catalysts, Co-ZSM5 and Cu-ZSM5, were successfully coated on the surface of the porous silica supports. During the removal test of HCHO using the prepared Co-ZSM5 and Cu-ZSM5 coated beads, depending on the reaction temperature, the Co-ZSM5 coated beads exhibited higher removal efficiencies (>97%) than the Cu-ZSM5 beads at 200 ℃. The higher efficiency of the Co-ZSM5 coating may be attributed to its superior surface activity properties (BET surface area and pore volume) that lead to the favorable HCHO decomposition. Therefore, Co-ZSM5 was determined to be the suitable catalyst for removing HCHO as a coating on a porous support fabricated using domestic low-grade silica.